Novy Pureline Cubic Installation Manual

Important Safety and Assembly Regulations

Please read these instructions carefully before installation and use. For more information on Novy products, accessories, and services, visit www.novy.com.

General Safety Precautions

• Wear protective gloves when handling metal parts due to potentially sharp edges.
• Ensure the structure where the appliance is mounted has sufficient load-bearing capacity.
• Only use original Novy parts for replacements.
• Respect the recommended installation height for optimal performance.
• The appliance or its supporting structure should cover the hob for optimal vapor absorption.
• Ensure the hob is not larger than the appliance or its structure.
• This appliance is for household use only and must not be used outdoors.
• Check the appliance and fittings for damage before installation. Do not install if damaged.
• Novy is not liable for damage due to incorrect assembly, connection, use, or operation.
• Installation and electrical connection must be performed by a qualified professional.
• Safety is only guaranteed with expert installation according to the manual.
• Installation is recommended with at least two people.

Installation Requirements

• The ceiling unit can be built into plates with a thickness of 18-35mm.
• Do not mount directly into gypsum board; use reinforcement for clamping screws.
• Ensure a socket is near the ceiling unit for easy power disconnection.
• The ceiling must have sufficient load-bearing capacity due to the appliance's weight.
• Recommended mounting height:
  • Electric or ceramic hob: min. 600 mm, max. 1600 mm.
  • Gas or induction hob: min. 650 mm, max. 1600 mm.

Electrical Connection

• Connect only to an earthed socket (230V – 50Hz).
• Ensure connection to an earth cable for safety.
• The appliance must be disconnectable from the power supply at any point.
• Position the socket for easy plug insertion.
• Do not use extension cords.
• Never switch on a faulty appliance. Contact Novy service for repairs.
• Moisture ingress can cause electric shock; avoid high-pressure or steam cleaners.

Air Supply and Ventilation

• Ensure adequate air supply; insufficient air reduces efficiency by 50% or more.
• Avoid using the hood with combustion systems (gas, oil, wood, coal heaters, etc.) without adequate ventilation, as combustion gases can be sucked back, leading to poisoning.
• Maintain negative pressure below 4 Pa (=0.04 mBar) when used with combustion appliances.
• Fresh air can be provided by opening windows/doors or installing air grilles.
• For appliances with external motor units, ensure sufficient air supply in the room.
• For recirculation units, minimum ventilation is also required.
• Consider a window contact switch for appliances used with heating systems that require room air.

Exhaust Duct Installation

• Motor outlet diameter is 150 mm; a 150 mm duct is recommended.
• Use the shortest possible duct with minimal bends for best performance and lowest noise.
• Use smooth, non-flammable pipes with the correct diameter.
• Flat ducts with rounded corners are recommended.
• Do not reduce the exhaust diameter.
• Avoid right-angle bends; use rounded bends.
• Flexible hoses should be used minimally.
• Ensure ducts are not crushed or kinked.
• Use hose clamps or aluminum tape for airtight connections.
• Horizontal ducts should be slightly inclined to prevent condensation.
• Insulate ducts passing through cool areas.
• Ensure exhaust pipes through external walls bridge cavities and slope slightly outwards.
• Use appropriate wall vents or roof passages.
• A non-return valve may be needed for short ducts to prevent wind ingress.
• Do not connect to active flues or chimneys serving other appliances.

Accessories

Various accessories are available to enhance the functionality and installation of your Novy Pureline Cubic hood.

Recirculation

Novy offers outlet boxes in various sizes for recirculation setups.

Motor Installation

• Remote motor installation is possible with an additional kit for silent operation.
• An adapter is available for connecting flat ducts directly to the ceiling unit.
• Extension cables are available for longer runs between the hood and the motor unit.

Ducting Accessories

A range of accessories for round and flat exhaust ducts are available, including:

• Ducting tubes (various lengths and diameters)
• Connection pieces
• Bends (90°, 15°)
• Wall grilles and through-wall kits
• Non-return valves
• Flexible exhaust tubes

General Accessories

• Hose clamps
• Aluminum tape
• Stainless steel cleaner

InTouch Compatibility

The hood can be controlled via the Novy InTouch induction hob.

Window Contact Switch

An optional window contact switch can be connected to ensure the hood only operates when a window is open, which is important when used with heating appliances that require room air.

Installation Steps

Follow these steps for installation:

1. Prepare the cut-out opening in the mounting plate according to the specified dimensions (6833/6834: 845x485mm; 6843/6844: 1145x485mm). Ensure the opening is watertight.
2. Mount the cooker hood with the control panel on the right side for easy access to the filter.
3. Connect external lighting (max. 300W) via the remote control if applicable.
4. Ensure the exhaust duct is connected securely using aluminum tape or a hose clamp. Keep the duct long enough for re-connection after disassembly.
5. Insert the plug into the wall socket.
6. Push the ceiling unit up into the opening, securing it with the clamping screws. Do not overtighten in plasterboard.
7. The motor unit's exhaust direction can be adjusted if necessary.

Refer to specific diagrams for detailed steps on exhaust direction and unit mounting.

Dimensions

Diagrams illustrating the dimensions for Novy Pureline Cubic models 6833/6834 and 6843/6844 are provided.