DOD MINI EXPRESSION PEDAL OWNER'S MANUAL
Thank you for purchasing the DOD Mini Expression Pedal, a miniature passive expression pedal that provides you with the full range of expressive control without taking up valuable space on your pedalboard.
Features
- Compact size takes up minimal space on the pedalboard
- Long sweep for full range of control
- High-quality, high-cycle 25k potentiometer for smooth expressive control
- Impedance switch changes from 25 kΩ (up/down) to 10 kΩ (center) to adapt to Line 6® style CC inputs
- Removable rubber feet for pedal mounting
- 1/4" jack with switchable TS, TRS, or RTS operation
- Non-slip tread pad
- Robust construction
Setup
- Connect cables (see connection diagram below).
- Select the correct cable connection setting (TS, TRS, or RTS) for the device you wish to control. (Refer to the owner's manual of the controlled device for the correct setting.)
- Press the tip of the DOD Mini Expression Pedal down.
- Configure the controlled device for the desired expression control type.
Connection Diagram
A diagram illustrates the connection of the DOD Mini Expression Pedal. It shows the pedal's "In" and "Out" jacks connecting to an effects processor's "Exp. Out" and "Exp. In" jacks, respectively. The effects processor also connects to a guitar. A note advises consulting the controlled device's manual to determine the correct cable type (TS, TRS, or RTS).
Important Usage Warning
Two hex screws on the bottom of the pedal are part of the spring-loaded adjustment mechanism. If you notice slippage over time, slightly loosen these screws and then retighten them. This will re-tension the main drive gear against the treadle gear. DO NOT remove these screws or tamper with the pedal while the screws are loose. This may cause gear misalignment and pedal failure. There are no user-serviceable parts inside the pedal. Under no circumstances should the pedal be opened.
Conformity and Safety Instructions
Altitude: ⛰️ Do not use this product above 2000m.
The following symbols are internationally accepted symbols that warn of potential risks associated with electrical products. A lightning bolt with an arrow in an equilateral triangle (⚡) means dangerous voltage is present within the unit. An exclamation mark in an equilateral triangle (❗) means the user should read the instruction manual.
These symbols indicate that there are no user-serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer's warranty. Do not wet the unit. If liquid is spilled on the unit, turn it off immediately and take it to the dealer for service. Disconnect the unit during thunderstorms (⚡) to prevent damage.
UK Mains Plug Warning
⚠️ A molded mains plug that has been cut off from the cord is unsafe. Dispose of the mains plug in a suitable disposal facility. NEVER insert a damaged or cut mains plug into a 13 AMP socket. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local dealer. Replacement fuses are 13 amps and MUST be ASTA approved to BS1362.
Disposal
♻️ To dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation requiring proper treatment, recovery, and recycling. Private households in the 25 EU member states, Switzerland, and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you are purchasing a similar new product). For countries not listed above, please contact your local authorities for information on the correct disposal method. This will ensure that your discarded product undergoes the necessary treatment, recovery, and recycling, thereby preventing potential negative impacts on the environment and human health.
General Precautions
- READ THESE INSTRUCTIONS.
- KEEP THESE INSTRUCTIONS.
- HEED ALL WARNINGS.
- FOLLOW ALL INSTRUCTIONS.
- DO NOT USE THIS APPARATUS NEAR WATER (?).
- CLEAN ONLY WITH A DRY CLOTH.
- FOR INDOOR USE ONLY.
- DO NOT BLOCK ANY VENTILATION OPENINGS (⚙️).
- INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT (?). USE ONLY ACCESSORIES/ACCESSORIES SPECIFIED BY THE MANUFACTURER. UNPLUG THIS APPARATUS DURING THUNDERSTORMS (⚡) OR WHEN UNUSED FOR LONG PERIODS.
Do not defeat the safety purpose of the polarized or grounding-type plug (?). A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician about replacing the obsolete outlet.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When used with a cart, use caution and move the apparatus/cart combination to avoid injury from tipping over.
All servicing should be referred to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled, or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
POWER SWITCH: The switch used in this apparatus does not break the connection to the mains. POWER DISCONNECTION: The plug must remain readily operable. When installed in a rack or where the plug is not accessible, a means of disconnecting the mains must be incorporated into the rack or building's electrical installation, with a multi-pole contact separation of at least 3 mm in each pole. When connecting to a 240V supply, a suitable CSA/UL certified power cord must be used.
Wiring Instructions
NOTICE TO CUSTOMERS: If your unit is supplied with a power cord.
WARNING: THIS APPARATUS MUST BE CONNECTED TO A SOCKET WITH PROTECTIVE EARTHING (?). The conductors of the mains lead are coloured in accordance with the following code:
GREEN AND YELLOW – EARTH / BLUE – NEUTRAL / BROWN – LIVE
As the colours of the conductors of the mains lead in this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
- The conductor which is coloured green and yellow must be connected to the terminal in the plug marked with the letter E, or by the earth symbol (?), or coloured green, or green and yellow.
- The conductor which is coloured blue must be connected to the terminal marked N or coloured black.
- The conductor which is coloured brown must be connected to the terminal marked L or coloured red.
This apparatus may require the use of other than line cords, or appliance couplers available from your installation source. If it is necessary to replace the appliance coupler, refer servicing to qualified service personnel who should consult the table below. The green/yellow cord should be connected directly to the chassis of the unit.
| CONDUCTOR | WIRE COLOR (Normal) | WIRE COLOR (Alt) | |
|---|---|---|---|
| L | LIVE | BROWN | BLACK |
| N | NEUTRAL | BLUE | WHITE |
| E | EARTH GND | GREEN/YEL | GREEN |
WARNING: If the earthing is imperfect, certain fault conditions in the unit or in the system to which it is connected may cause full mains voltage to be present between the chassis and earth. If you simultaneously touch the chassis and earth, the result may be severe injury or death (⚡ ⚠️).
