Babyliss AS960E Brosse Coiffante

How to Use

Ensure your hair is 80% dry and combed through to remove any tangles. Create your parting and divide the hair into sections ready for styling.

Secure the selected attachment onto the airstyler.

Slide the switch to the '*', 'I' or 'II' position to turn the appliance on and select a heat setting suitable for your hair type.

After use, slide the switch to the '0' setting to switch off and unplug the appliance.

Allow the appliance to cool before storing away.

IMPORTANT! Always allow the attachments to cool before storing in the provided pouch.

Changing the Attachments

Place the attachment onto the handle and line up the two indents on the attachment with the buttons on the handle.

Push the attachment onto the handle until it clicks into place.

To remove an attachment, press and hold the two buttons on the handle and pull the attachment up and away.

Attachments

Rotating 50mm Soft Bristle Brush Attachment

To make the brush rotate, press and hold the buttons marked '<<' and '>>'. This will make the brush head rotate clockwise and anti-clockwise.

• Place the brush underneath the hair section close to the scalp and hold for a few seconds to boost volume at the roots.
• Move the styler down through the hair and start to rotate the brush away from your head by pressing and holding the appropriate rotation button.
• As you do this, resist the rotation of the brush by pulling the brush downwards. This will create tension through the section of hair.

IMPORTANT! It may take several attempts to perfect this technique; if the brush spins too quickly, simply release the rotation button and remove from the hair.

• As you reach the ends of the hair section, continue rotating the brush to roll the ends under.
• Repeat for each section of hair.

20mm Soft Bristle Brush Attachment

• Place the brush head under a section of hair, close to the roots.
• Slowly move the brush down along the section, towards the ends of the hair. Rotate the appliance slightly to curl the ends under.
• Repeat for each section of hair.

Straightening Attachment

Turn the tension control dial on the top of the straightening attachment to select the required setting for your hair type.

Please note: When using the straightening attachment for the first time, select setting 1 and gradually increase the tension until the desired result is achieved.

Below is a guide of the tension settings:

• Fine = Setting 1
• Medium = Setting 2
• Thick = Setting 3
• Curly = Setting 4

• Place the straightening attachment under a section of hair, as close to the roots as possible with the straightening comb pointing away from your head.
• Use your other hand to pull the hair section taut against the brush head until the straightening combs penetrate through the hair.
• Gently glide the straightening brush through the section of hair, until you reach the ends.
• Repeat for each section of hair.

Drying Nozzle Attachment

Direct the airflow onto the hair and move the airstyler around the head to remove excess moisture pre-styling.

Heat Settings

There are 2 heat settings plus a cool setting. Slide the switch to the first position to select the cool setting '*', the second position for the low heat 'I', and the third position for the high heat 'II'.

Please note: If you have delicate, fine, bleached or coloured hair, use the lower heat settings. For thicker hair, use the higher heat setting.

Cleaning & Maintenance

General

• Ensure the appliance is switched off, unplugged and cool.
• To clean the outside of the appliance, wipe with a damp cloth. Make sure that no water enters the appliance and it is completely dry before use.
• Do not wrap the lead around the appliance; instead coil the lead loosely by the side of the appliance.
• Do not use the appliance at a stretch from the power point.
• Always unplug after use.

Cleaning the Filter

• Ensure the appliance is switched off, unplugged and cool.
• Holding the handle of the appliance firmly, lift the filter open from the grooves close to the cord bushing. This will enable the rear filter top open.
• Using a soft brush, clean any hair and other debris from the filter.
• Replace the rear filter by closing the lid shut.