BaByliss AS6550E Air Wand User Manual
This guide provides instructions for using the BaByliss AS6550E Air Wand for drying and styling hair.
Instructions for Use
Before using the appliance, please read the safety instructions.
- Ensure hair is towel-dried and combed through to remove excess water and tangles. Divide hair into sections ready for drying/styling.
- Use the Air Wand without an attachment to dry hair. To style, attach the desired brush head to the handle. Refer to the 'Changing the Attachments' section for interchange instructions.
- Slide the switch to the 'on' position and select a temperature and airflow setting suitable for your hair type.
Note: A blue LED light illuminates below the air outlet to indicate the anti-frizz ionic feature is activated.
After use, slide the switch to the 'off' position to switch off and unplug the appliance. Allow the appliance to cool before storing.
Changing the Attachments
Position the attachment over the air outlet with the hooks on the rear of the attachment located at the top. At a slight angle, with the bottom of the attachment touching the appliance, gently push the top of the attachment onto the handle until it clicks into place.
NOTE: Be careful not to touch the surround of the air outlet as this will become hot after use.
Drying
- Use the Air Wand without an attachment to dry hair.
- Direct the airflow down the hair shaft to smooth the section as you dry.
- For a lasting style, select the cool setting and gently blow through warm hair to set and smooth.
- Repeat for each section of hair.
Styling Attachments
Straightening Brush
- Place the brush head underneath or above a section of hair, close to the scalp with the firm bristles pointing upwards.
- Using the brush over the hair section helps to detangle and straighten thinner hair. Place the brush underneath the hair section to help straighten thicker hair and add volume.
- Use your other hand to pull the hair section taut against the brush head until the firm bristles penetrate through the hair.
- Gently glide the brush head through the section, creating tension and control through the hair to straighten the section as you dry.
- For a lasting style, select the cool setting and brush through warm hair to set and smooth.
- Repeat for each section of hair.
Curved Blow Dry Brush
- Place the brush head underneath a section of hair, close to the scalp with the flexible bristles pointing upwards.
- Use the brush head to lift hair at the roots and hold for a few seconds to boost volume at the root as you dry.
- Slowly move the brush head down through each section to dry, add shape and volume.
- For a lasting style, select the cool setting and brush through warm hair to set and smooth.
- Repeat for each section of hair.
Airflow / Temperature Settings
There are 3 airflow and 4 temperature settings, including a cool setting.
When turning on the Air Wand, the default airflow and temperature settings activate: airflow: III & Temperature: I.
To set the airflow, press the button until the desired airflow speed is reached. A white LED illuminates for each of the three airflow speeds.
To set the temperature, press the button until the desired temperature is reached. A red LED illuminates for each of the three heat settings. Press the button a fourth time to activate the cool setting – the 3 LEDs will change from red to blue.
When choosing a temperature setting, start with the lowest setting and increase as required. For delicate, fine, bleached, or colored hair, use lower heat settings. For thicker hair, use higher heat settings. Use the cool setting on warm hair to set your style.
Advanced Care Mode
To activate Advanced Care Mode, press and hold the temperature setting button for 1-2 seconds until the temperature LEDs alternate between red and blue, indicating the airflow is cycling between hot and cool. To turn off Advanced Care Mode, press the temperature button once to return to your chosen heat setting.
Anti-Frizz Technology
The advanced moisture-balancing dual ionic system combines positive and negative ions to eliminate frizz during drying and styling, leaving hair feeling silky, conditioned, and with luxurious shine.
Removable Magnetic Filter
The removable magnetic inlet filter facilitates easy cleaning and optimizes the dryer's airflow for fast drying performance.
Care & Maintenance
- Ensure the appliance is switched off, unplugged, and cool. Wipe the exterior with a damp cloth. Ensure no water enters the appliance and it is completely dry before use.
- Do not wrap the cord around the appliance; coil it loosely by the side.
- Do not use the appliance at a stretch from the power point.
- Always unplug after use.
Cleaning the Removable Magnetic Inlet Filter
- To increase product lifespan, keep the inlet filter clean.
- Ensure the appliance is switched off, unplugged, and cool.
- Using a soft brush, clean any hair and other debris from the filter.
Product Information
Model: AS6550E
Manufacturer: BABYLISS SARL
Address: ZI du Val de Calvigny, 59141 Iwuy, France
Website: www.babyliss.com
Made in China
