Dimension Guide
Maytag® Top Load Washer
This document provides detailed planning dimensions and electrical requirements for Maytag Top Load Washers, including models MVW4505MW, MVW5035MW, MVW5430MW, 7MMVW5035MW, and 7MMVW5435MW.
WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS and INSTALLATION INSTRUCTIONS, located in your appliance's Owner's Manual, before installing and operating this appliance.
Electrical Requirements
| Model | Capacity (US) | Capacity (CAN) |
| MVW4505MW | 4.5 cu ft DOE | 5.2 cu ft IEC |
| MVW5035MW | 4.5 cu ft DOE | 5.2 cu ft IEC |
| MVW5430MW | 4.8 cu ft DOE | 5.5 cu ft IEC |
| 7MMVW5035MW | 4.5 cu ft DOE | 5.2 cu ft IEC |
| 7MMVW5435MW | 4.7 cu ft DOE | 5.4 cu ft IEC |
| Minimum Circuit Amperage Rating | 15 A |
| Operating Voltage | 120 V AC only |
| Operating Frequency | 60 Hz |
Diagram showing front view of washer with dimensions labeled A, B, C, D.
Diagram showing rear view of washer with dimensions labeled E, F, G, H, I, J, K, L, M.
Product Dimensions
MVW4505MW, MVW5035MW, MVW5430MW, 7MMVW5035MW, 7MMVW5435MW
| Dimension | Unit | Minimum | Maximum |
|---|---|---|---|
| A: Height (with feet) | in | 43 1/4 | 44 1/4 |
| A: Height (with feet) | mm | 1100 | 1122 |
| B: Width | in | 27 3/4 | - |
| B: Width | mm | 683 | - |
| C: Top of Lid Height (with feet) | in | 38 | 39 |
| C: Top of Lid Height (with feet) | mm | 966 | 988 |
| D: Depth | in | 27 | - |
| D: Depth | mm | 692 | - |
| E: Height with Lid Open | in | 55 3/4 | 56 3/8 |
| E: Height with Lid Open | mm | 1415 | 1432 |
| F: Height of Lid | in | 18 7/8 | - |
| F: Height of Lid | mm | 449 | - |
| G: Width of Lid | in | 23 1/4 | - |
| G: Width of Lid | mm | 593 | - |
| H: Water Inlet Valves Height | in | 37 7/8 | 39 1/2 |
| H: Water Inlet Valves Height | mm | 962 | 1003 |
| I: Water Inlet Valves from Side | in | 4 1/2 | - |
| I: Water Inlet Valves from Side | mm | 116 | - |
| J: Power Cord from Side | in | 2 1/2 | - |
| J: Power Cord from Side | mm | 63 | - |
| K: Power Cord Height | in | 37 3/8 | 37 1/2 |
| K: Power Cord Height | mm | 950 | 953 |
| Power Cord Length | in | 62 | - |
| Power Cord Length | mm | 1530 | - |
| L: Drain Hose Outlet Height | in | 7 1/4 | 7 3/4 |
| L: Drain Hose Outlet Height | mm | 170 | 197 |
| M: Drain Hose Outlet from Side | in | 4 5/16 | - |
| M: Drain Hose Outlet from Side | mm | 107 | - |
| Drain Hose Length | in | 41 | - |
| Drain Hose Length | mm | 1040 | - |
| Diameter of Drain Hose | in | 1 | - |
| Diameter of Drain Hose | mm | 25 | - |
Espacement pour une installation dans un encastrement ou dans un placard (Recessed area or closet installation)
Diagram illustrating recommended spacing for installing the washer in a recessed area or closet. Shows clearances for walls, doors, and floor moldings, as well as ventilation openings.
The dimensions shown represent recommended spacing, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.
