Manuals+

Programming Guide for Allo Telecommande V2 Remote Controls

This document outlines the procedure for programming Allo Telecommande V2 remote controls with the RX WALLY and RXP receivers.

Programming V2 Remotes with RX WALLY Receiver

Follow these steps to register your V2 remote control with the RX WALLY receiver:

  1. Unscrew the antenna.
  2. Lift the cover.
  3. Using the SW1 button:
    • Press 1 time for channel 1.
    • Press 2 times for channel 2.
    • Press 3 times for channel 3.
    • Press 4 times for channel 4.

    The corresponding indicator light (L1, L2, L3, or L4) will remain illuminated.

  4. Within 10 seconds, press and hold the button on your new remote control for 2 seconds.
  5. The indicator light will flash, indicating successful registration.
  6. Wait for the indicator light to turn off.
  7. Test the remote control.

For automatic portal advice, contact: 0899 158 148 (1.35€/call - 0.34€/minute).

Programming V2 Remotes with RXP Receiver

Follow these steps to register your V2 remote control with the RXP receiver:

  1. Press and hold the 'CANC' button for 3 seconds until "rL" appears on the display.
  2. Use the 'UP' or 'DOWN' buttons to select the desired menu.
  3. By default, select '1' (relay 1) and confirm by pressing the 'CANC' button once.
  4. Use the 'UP' and 'DOWN' buttons to display "Mon" and confirm with the 'CANC' button.
  5. Use the 'UP' and 'DOWN' buttons to display "Tel" and confirm with the 'CANC' button.
  6. Use the 'UP' and 'DOWN' buttons to select an available memory zone number. The display will flash if the zone is occupied, and will not flash if the zone is free.
  7. Take the new remote control and press and hold the button to be registered for more than 2 seconds.
  8. To confirm and exit the menu, press the 'CANC' button.
  9. Use the 'UP' and 'DOWN' buttons to display "End", then exit programming mode by pressing the 'CANC' button.

Receiver Connections (RXP):

The RXP receiver has the following connections:

For automatic portal advice, contact: 0899 158 148 (1.35€/call - 0.34€/minute).

PDF preview unavailable. Download the PDF instead.

Programmation-V2-Contr-47 GPL Ghostscript 9.55.0 PDF Presentation Adobe Photoshop

Related Documents

Preview Programming a Dip-Switch Remote Control | Allo Télécommande
Learn how to program a dip-switch remote control for your installation. This guide provides step-by-step instructions on coding your remote.
Preview Programming Guide for TELECO 433 Remote Control
Instructions on how to program a new TELECO 433 remote control using an existing one, with detailed steps and visual examples. Includes important compatibility notes.
Preview Programming Auto-Learning Remote Controls
A guide to programming auto-learning remote controls, providing generic procedures and important attention points for successful setup.
Preview Allo Telecommande Product Exchange Form Under Warranty
Formulaire d'échange pour produit sous garantie from Allo Telecommande. This document outlines the steps for returning a product for exchange under warranty, including required information and shipping instructions.
Preview Formulaire de retour de produit usagé - ALLO Télécommande
Formulaire pour le retour de produits usagés d'Allotélécommande. Ce document permet aux clients de retourner des produits pour recyclage dans le cadre d'une démarche de développement durable.
Preview REMOCON RMC 168 SL Programming Instructions
Step-by-step guide for programming the REMOCON RMC 168 SL remote control using an already programmed remote.
Preview Programming Notice for ADYX TE4433H / GENIUS ECHO TX4 Remote Controls
This document provides programming instructions for the ADYX TE4433H and GENIUS ECHO TX4 remote controls operating at 433 MHz. Learn how to memorize your remote control to the receiver module.