MD SPORTS Shuffleboard Table Assembly Instructions

Warranty Information

English: LIMITED 90 DAYS WARRANTY. This product is covered by a limited warranty that is effective for 90 days from the date of purchase. If, during the limited warranty period, a part is found to be defective or breaks, MD SPORTS will offer replacement parts at no cost to the customer. The only exceptions to the warranty include mainframes, table tops, playing surfaces, batteries or tools. The above warranty will not apply in cases of damages due to improper usage, alteration, misuse, abuse, accidental damage or neglect. This Limited Warranty gives you specific legal rights and you may also have other rights vary from one State (province) to another.

Español: GARANTÍA LIMITADA DE 90 DÍAS. Este producto está cubierto por una garantía efectiva de 90 días a partir de la fecha de su compra. Durante el período límite de la garantía, si una parte defectuosa o quebrada es encontrada, MD SPORTS ofrecerá una reparación o un reemplazo de la partes sin ningún costo para el cliente. Las únicas excepciones de la garantía incluyen unidad principales, tableros de mesa, superficies, pilas o herramientas. La susodicha garantía no se aplicará en los casos de daños y perjuicios debido al uso impropio, la alteración, el mal uso, el abuso, el daño accidental o la negligencia. Esta garantía limitada le da a usted derechos legales específicos, usted también puede tener otros derechos que varían de un estado (provincia) a otro.

Français: GARANTÍA LIMITA DE 90 DIAS. Ce produit est couvert par une garantie limitée valable 90 jours à compter de la date d'achat. Si pendant cette période une pièce est jugée défectueuse ou se casse, MD SPORTS la remplacera gratuitement. Les seules exceptions à la garantie comprennent les armatures principales, les dessus de table, les surfaces de jeu, les piles ou les outils. La garantie ci-dessus ne s'applique pas en cas de dommages occasionnés par une mauvaise utilisation, une altération du produit, de mauvais traitements, des dommages accidentels ou des négligences. Cette garantie limitée vous accorde des droits légaux spécifiques ainsi que d'autres droits variant d'un état (province) à un autre.

A PURCHASE RECEIPT (or other proof of purchase) will be required before any warranty service is initiated. For all requests for warranty service, please feel free to contact our Consumer Service Department.

Contact Information:

• Phone: 877-472-4296
• Website: www.medalsports.com
• Customer Service Hours: Mon.-Fri., 9:00 a.m. to 5:00 p.m. EST

Important Note: Please contact MD SPORTS before returning the product to the store.

Tools Required

• Phillips Screwdriver - Not Included
• Standard (Flat Head) Screwdriver - Not Included
• Allen Key - Included

Recommended: Electric screwdrivers may be helpful during assembly; however, please set a low torque and use extreme caution.

Important Notice

1. This product is intended for INDOOR use only.
2. Please do not sit, climb or lean on the product.
3. Please do not drag the product when moving it in order to avoid damaging the legs.
4. Please only use spray furniture polish to clean the exterior surfaces of the product.
5. This is not a children's toy; adult supervision is required for children playing this game.

Safety Warnings:

• Adult Assembly Required.
• CHOKING HAZARD: This item contains small parts. Not suitable for children under 3 years.
• Keep away from pets in assembly area.
• Do not use or keep product outdoors. For indoor use only. Not for wet/humid conditions.

Parts Identifier

Accessories

Hardware

Pre-installed Parts

Assembly Steps

Before Assembly

1. Find a clean, level place to begin the assembly of your product.
2. Verify that you have all listed parts as shown on the part list pages. If any parts are missing, call MD SPORTS customer service.

Step 1: Mainframe Assembly

Refer to Figure 1. Attach the Support Braces (part 2) to the Mainframe (part 1) using T4x1-1/4" Screws (A1).

Step 2: Leg Assembly

Refer to Figure 2. Attach the Side Leg Panels (part 4) and End Leg Panels (part 5) to the Mainframe assembly. Use 1/4"x3/4" Bolts (A2), 1/4"x1" Bolts (A3), 1/4" Washers (A4), 5/16"x1-1/4" Bolts (A5), 5/16" Washers (A6), and 5/16"x2-3/4" Wing Bolts (A7) as indicated in the diagram. Ensure pre-installed parts P2 and P3 are used correctly.

Step 3: Support and Stability

Refer to Figure 3. Attach additional Support Braces (part 6) to the leg structure using 1/4"x3/4" Bolts (A2) and 1/4" Washers (A4). Also, attach the Connecting Boards (part 3) using the same hardware.

Step 4: Final Leg Connections

Refer to Figure 4. Secure the leg structure further using T4x1" Screws (A8).

Step 5: Final Tightening and Table Placement

Refer to Figure 5. Go back and make sure that all connections are tight. Use 5/16"x1-1/4" Bolts (A5), 5/16" Washers (A6), 1/4"x1" Bolts (A3), 1/4" Washers (A4), and Allen Key (A10) for final tightening. Carefully turn the table over onto its feet, ensuring it is stable.

Caution: Four strong adults are recommended to turn over the table. Lift the table off the ground, turn it over, and place it on all four feet simultaneously.

Step 6: Slide Scorer Attachment

Refer to Figure 6. Attach the Slide Scorers (part 9) to the ends of the table using T4x5/8" Screws (A9).

How to Level Your Table

Step 1: Initial Leveling

Place a level (not included) on the playing surface. Adjust the Leg Levelers (part 8) by turning clockwise to raise and counterclockwise to lower until the table is level.

Step 2: Fine-Tuning

Use the Leg Levelers (part 7, likely referring to the adjustable feet which are part 8 in the parts list) to fine-tune the table's level. Turn clockwise to lower and anti-clockwise to raise. Adjust for concave or convex table surfaces as needed.

Note: Turn clockwise to raise and counterclockwise to lower for the leg levelers.

You are now ready to play!