MD Sports AC284Y21005 Roll and Score Arcade Game Assembly Instructions & Manual

LIMITED 90 DAYS WARRANTY

This product is covered by a limited warranty effective for 90 days from the date of purchase. During this period, defective or broken parts will be replaced at no cost to the customer. Exceptions include mainframes, table tops, playing surfaces, batteries, or tools. This warranty does not apply to damages from improper usage, alteration, misuse, abuse, accidental damage, or neglect. This Limited Warranty grants specific legal rights, which may vary by state or province. A purchase receipt or other proof of purchase is required for warranty service. For all warranty requests, please contact our Consumer Service Department. Please be aware of your product's Limited Warranty for the store's return/refund policy. Medal Sports cannot handle products outside their limited warranty as they only provide available parts. Thank you!

PLEASE CONTACT US BEFORE RETURNING THE PRODUCT TO THE STORE!

WE ARE READY TO HELP | DO NOT RETURN TO STORE

ESTAMOS LISTOS PARA AYUDAR | NO DEVOLVERLO A LA TIENDA

Customer Service Toll Free: 877-472-4296

Hours: Mon.-Fri., 9:00 a.m. to 5:00 p.m. EST | Lunes a Viernes, 9:00 a.m. a 5:00 p.m. ET

For additional resources and Frequently Asked Questions, please visit us at: www.medalsports.com

TOOLS REQUIRED

Phillips Screwdriver Standard (Flat Head Screwdriver) - Not Included
Allen Key - Included

IMPORTANT NOTICE

This product is intended for INDOOR use only.
Please do not sit, climb, or lean on the product.
Please do not drag the product when moving it in order to avoid damaging the legs.
Please only use furniture polish spray to clean the exterior surfaces of the product.
Adult supervision is required for children playing this game.

? At least 2 adults needed

? No children in assembly area

? Keep away from pets in assembly area

? Do not use or keep product outdoors. For indoor use only. No wet/humid conditions.

⚠️ WARNING

Adult assembly required. CHOKING HAZARD - This item contains small parts. Not suitable for children under 3 years.

PARTS IDENTIFIER

Part Number	Part Name	Quantity	Figure Reference
1	Target Board with Sensor	x1	FIG. 19
2	End Leg Panel - A	x1	FIG. 17
3	Leg - A	x1	FIG. 16
4	Leg - B	x1	FIG. 16
5	Bottom Board	x1	FIG. 18
6	Leg - C	x1	FIG. 16
7	Leg - D	x1	FIG. 16
8	Playfield - A	x1	FIG. 4, 10, 11, 12, 14, 15, 18, 19
9	Top Panel	x1	FIG. 4, 8, 9, 10, 11, 12, 18, 19, 20, 21
10	Back Board	x1	FIG. 4, 20, 21
11	End Leg Panel - B	x1	FIG. 17
12	Side Apron - A	x1	FIG. 4, 5, 7, 11, 12, 14, 15
13	Side Apron - B	x1	FIG. 4, 5, 7, 11, 12, 14, 15
14	Side Apron - C	x1	FIG. 3, 6, 7, 8, 11, 12, 14, 15, 17
15	Side Apron - D	x1	FIG. 3, 6, 7, 11, 12, 14, 15, 17
16	Playfield - B	x1	FIG. 2, 3, 6, 7, 11, 12, 14, 15
17	Support Board - A	x1	FIG. 3, 11, 12, 14, 15, 16, 17
18	End Apron	x1	FIG. 2
19	Goal Box Board	x1	FIG. 2, 7
20	Support Board - B	x1	FIG. 2, 14, 16
21	Complementary Plate	x1	FIG. 21
22	Support Board - C	x2	FIG. 13, 14, 15
23	Glue	x1	FIG. 8
24	Connecting Board	x2	FIG. 5, 10, 14
25	Support Board - D	x1	FIG. 5, 14
26	Ball Return Board - A	x1	FIG. 13, 14, 15, 16
27	Ball Return Board - B	x1	FIG. 13, 14, 15, 16
28	"L" Bracket	x2	FIG. 12
29	Back Panel-A	x1	FIG. 8, 10, 12, 18, 19, 20
30	Back Panel-B	x1	FIG. 8, 10, 18, 19, 20, 21
31	Electronic Scorer	x1	FIG. 9, 13, 19, 20, 21, 23
32	Support Board - E	x2	FIG. 18
33	Ball	x3	ACCESSORIES
A1	4x45mm Screw	x10	FIG. 5, 8
A2	4x15mm Screw	x6	FIG. 9, 13
A3	3.5x28mm Screw	x63	FIG. 1, 2, 3, 4, 14, 17, 19, 20, 21
A4	4x32mm Screw	x4	FIG. 12
A5	M6x28mm Butterfly Bolt	x16	FIG. 3, 6, 7, 10
A6	4x51mm Screw	x2	FIG. 2
A7	M6x22mm Bolt	x14	FIG. 3, 11, 16
A8	M6 Washer	x14	FIG. 3, 11, 16
A9	3x28mm Flat Head Screw	x2	FIG. 4
A10	Allen Key	x1	FIG. 4, 11, 16
P1	LED	x1	PRE-INSTALLED PARTS
P2	M6 T - Nut	x16	PRE-INSTALLED PARTS
P3	Target Sensor Wire	x5	PRE-INSTALLED PARTS
P4	Control Switch	x1	PRE-INSTALLED PARTS

ASSEMBLY

FIG. 1

Step 1: Attach part 14 (End Leg Panel - A) and part 15 (End Leg Panel - B) to the bottom board. Use 6x A3 screws.

Step 2: Attach part 16 (Playfield - B) to the assembled base. Use 1x P4 (Control Switch) and 1x A3 screw.

Note: Ensure the "Wall / Pared" side is oriented correctly.

FIG. 2

Step 1: Attach part 18 (End Apron) and part 20 (Support Board - B) to the structure. Use 11x A3 screws and 2x A6 screws.

Note: Black side of part 18 is facing down. Black laminate of part 20 is on this side.

FIG. 3

Step 1: Attach part 17 (Support Board - A) to the side panels. Use 4x A5 screws, 1x A7 bolt, and 1x A8 washer.

Step 2: Attach part 14 (Side Apron - C) and part 15 (Side Apron - D) to the structure. Use 1x A7 bolt and 1x A8 washer.

Note: Ensure the hole/orifice is aligned correctly.

FIG. 4

Step 1: Attach part 8 (Playfield - A) and part 13 (Side Apron - B) to the side panels. Use 6x A3 screws and 2x A9 screws.

Note: Ensure the "Wall / Pared" side is oriented correctly.

FIG. 5

Step 1: Attach part 25 (Support Board - D) to the structure. Use 4x A1 screws.

Note: Ensure the hole/orifice is aligned correctly.

FIG. 6

Step 1: Attach part 24 (Connecting Board) to the structure. Use 8x P2 (M6 T-Nut) and 4x A5 screws.

FIG. 7

Step 1: Connect the assembly from FIG. 6 to the assembly from FIG. 3. Use 4x A5 screws.

FIG. 8

Step 1: Apply glue (23) into the grooves of the Top Panel (9). Use 1x P1 (LED) and 1x 29 (Back Panel-A).

Step 2: Attach part 30 (Back Panel-B) to the structure. Use 6x A1 screws.

Note: Apply the Glue (23) into the grooves of the Top Panel (9).

FIG. 9

Step 1: Attach part 31 (Electronic Scorer) to the Top Panel (9). Use 1x A2 screw.

Step 2: Connect the wiring from P1 (LED) and 31 (Electronic Scorer) as shown in the bottom view.

FIG. 10

Step 1: Combine the assembly from FIG. 9 with the assembly from FIG. 7. Use 4x A5 screws.

FIG. 11

Step 1: Attach part 17 (Support Board - A) using 1x A7 bolt, 1x A8 washer.

Step 2: Attach part 13 (Side Apron - B) using 1x A7 bolt, 1x A8 washer.

Step 3: Attach part 15 (Side Apron - D) using 1x A7 bolt, 1x A8 washer.

Step 4: Attach part 14 (Side Apron - C) using 1x A7 bolt, 1x A8 washer.

FIG. 12

Step 1: Attach part 28 ("L" Bracket) using 2x A4 screws.

Step 2: Attach part 28 ("L" Bracket) using 2x A4 screws.

FIG. 13

Step 1: Attach parts 26 (Ball Return Board - A) and 27 (Ball Return Board - B) to the structure. Use 4x A2 screws.

Step 2: Connect parts 26 & 27 as shown.

FIG. 14

Step 1: Attach part 25 (Support Board - D) using 4x A3 screws.

Step 2: Attach parts 26 (Ball Return Board - A) and 27 (Ball Return Board - B) using the provided connections.

Step 3: Attach part 17 (Support Board - A) and part 22 (Support Board - C) using A3 screws.

FIG. 15

Step 1: Attach part P4 (Control Switch) to the structure.

FIG. 16

Step 1: Attach parts 3 (Leg - A), 4 (Leg - B), 6 (Leg - C), and 7 (Leg - D) to the base. Use 12x A7 bolts and 12x A8 washers.

Step 2: Attach part 1 (Target Board with Sensor) using 1x A10 Allen Key.

FIG. 17

Step 1: Attach part 2 (End Leg Panel - A) and part 11 (End Leg Panel - B) to the main body. Use 12x A3 screws.

Note: Go back and make sure that all connections are tightened.

CAUTION: Two strong adults are recommended to turn over the table as shown. 1. Lift the table off the ground. 2. Turn the table over. 3. Place it on all feet at the same time on the ground.

[Icon: Hold by tabletop] / [Icon: Cabinet] [Icon: Do not hold by legs] [Icon: Do not lean on legs]

FIG. 18

Step 1: Attach part 5 (Bottom Board) and part 32 (Support Board - E) to the structure. Use 8x A3 screws.

Note: Black side of part 5 is facing up.

FIG. 19

Step 1: Attach part 1 (Target Board with Sensor) to the structure. Use 2x A3 screws.

Step 2: Connect the wiring from 31 (Electronic Scorer) and P4 (Control Switch) as shown.

FIG. 20

Step 1: Attach part 10 (Back Board) to the structure. Use 10x A3 screws.

Step 2: Connect wiring from 31 (Electronic Scorer) and P4 (Control Switch) to part 1.

FIG. 21

Step 1: Attach part 21 (Complementary Plate) to the structure. Use 4x A3 screws.

Step 2: Connect the electronic components as shown in the diagram.

ELECTRONIC CONNECTIONS DIAGRAM: [Diagram description: Shows connections between 31 (Scorer), P4 (Switch), P1 (LED), 1 (Target Board), 10 (Back Board), 21 (Plate), and P3 (Sensor Wire)].

ELECTRONIC SCORER OPERATION

BATTERY INSTALLATION

Battery Box: Unscrew the bolt using a screwdriver and open the battery box. Insert 3x1.5V "AAA" batteries (not included) in the order of polarity as shown on the inside cover. Then close the cover using a screwdriver.

? REMINDING

The batteries must be installed according to their correct polarization (+ and -).
Please clean the battery contacts and also those of the device prior to battery installation.
If the game will not be used for a long period of time, we recommend removing the batteries.

⚠️ WARNING

Requires 3x1.5V "AAA" batteries (not included).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.

HOW TO PLAY

Control box operation:

Press [play/pause button] to activate the scorer. The scoreboard "PLAYER" shows "1" (pre-set single-player mode).
Press the [mode button] again to switch between single-player and double-player modes.
Press [enter button] to enter the selected game mode.
Press [sound button] to switch the sound ON / OFF while playing.
Press and hold the [power button] for 3 seconds to turn off the scorer.

Game Modes & Rules:

Auto-Off: If no shot is made or no button is pressed within 5 minutes, the scorer turns off automatically. Unplug the power when not in use.
Return to Mode Selection: During the game, press the [mode button] to return to function selection mode and reselect the game mode.
Single-player mode: Press the [play/pause button]. The score screen will show "000" to start. Each round counts 9 times. Game ends after 9 score counts for Player 1.
Double-player mode: Press the [play/pause button]. The player screen shows "1" to start for Player 1. Game ends after 9 score counts for Player 1. Then, the screen shows "2" to start for Player 2. Game ends after 9 score counts for Player 2.
Scores comparison display: PLAY1>PLAY2 (Player 1 wins sound), PLAY2>PLAY1 (Player 2 wins sound), PLAY1=PLAY2 (Tied game sound).
Restart/Change Mode: After the game, press [play/pause button] to restart or [mode button] to choose other game modes.
Score rules: 10 points for 10-point hole, 20 points for 20-point hole, 30 points for 30-point hole, 50 points for 50-point hole.
Caution: Do not "Throw" the ball at the target board as damage may occur. Always "roll" the ball along the runway for correct and safe operation.

DISCLAIMER

⚠️ WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE (FCC Compliance)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with the Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.

For additional resources, please contact Medal Sports Corp.
1300 Melissa Drive, Suite 124, Bentonville, AR 72712
Toll Free: 877-472-4296

[Icon: You are now ready to play!] [Icon: ¡Usted está ahora listo para jugar!]

	MD SPORTS AC220Y22004 Roll and Score Arcade Game Assembly Instructions This document provides comprehensive assembly instructions, safety warnings, warranty information, parts list, and gameplay details for the MD SPORTS AC220Y22004 Roll and Score Arcade Game.
	MD SPORTS BG138Y22001 Arcade Basketball Game Assembly Instructions Comprehensive assembly instructions for the MD SPORTS BG138Y22001 Arcade Basketball Game. Includes a detailed parts list, hardware guide, assembly steps, control box operation, game options, and safety information.
	MD SPORTS BG135Y22002 Arcade Basketball Game Assembly Instructions Comprehensive assembly instructions for the MD SPORTS BG135Y22002 Arcade Basketball Game, including parts lists, hardware details, assembly steps, electronic scorer operation, and game options. Features a 90-day limited warranty.
	MD Sports BG138Y22004 Assembly Instructions and Game Guide Comprehensive assembly instructions, game options, and electronic scorer operation for the MD Sports BG138Y22004 arcade basketball game. Includes parts list, safety guidelines, and warranty information.
	MD SPORTS Electronic Dartboard Assembly Instructions and Game Guide Comprehensive assembly instructions, parts list, mounting guide, operation details, and a summary of game modes for the MD SPORTS Electronic Dartboard (Model DB300Y19003). Includes safety warnings and important notes for optimal use.
	MD Sports BG300Y21002 2-in-1 Basketball and Baseball Pitchback Assembly Instructions Comprehensive assembly instructions and user guide for the MD Sports BG300Y21002 2-in-1 Basketball and Baseball Pitchback training game. Includes parts list, hardware identification, step-by-step assembly, and game instructions.
	MD SPORTS BL066Y22015 Billiard Table Assembly Instructions Comprehensive assembly instructions for the MD SPORTS BL066Y22015 billiard table, including parts list, tools required, step-by-step guidance, and leveling tips.
	MD Sports BL084Y23006 Multi-Game Table Assembly Instructions Step-by-step assembly guide for the MD Sports BL084Y23006 multi-game table, featuring billiard and table tennis modes. Includes parts list, hardware, warranty information, and safety precautions.

MD SPORTS Assembly Instructions

LIMITED 90 DAYS WARRANTY

TOOLS REQUIRED

RECOMMENDED

IMPORTANT NOTICE

⚠️ WARNING

PARTS IDENTIFIER

ASSEMBLY

FIG. 1

FIG. 2

FIG. 3

FIG. 4

FIG. 5

FIG. 6

FIG. 7

FIG. 8

FIG. 9

FIG. 10

FIG. 11

FIG. 12

FIG. 13

FIG. 14

FIG. 15

FIG. 16

FIG. 17

FIG. 18

FIG. 19

FIG. 20

FIG. 21

ELECTRONIC SCORER OPERATION

BATTERY INSTALLATION

? REMINDING

⚠️ WARNING

HOW TO PLAY

DISCLAIMER

⚠️ WARNING

NOTE (FCC Compliance)

Related Documents