WALI WL-MF002 Installation Manual
support@walielectric.com
Unpacking Instructions
Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
Check package contents against the Supplied Parts List to assure that all components were received undamaged. Do not use damaged or defective parts.
Carefully read all instructions before attempting installation.
Important Safety Information
Install and operate this device with care. Please read this instruction before installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation.
Please call a qualified installation contractor for help if you don't understand these directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. WALI disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.
Supplied Parts List
- (1) Pole-a
- (1) Weighted Base-b
- (1) Swivel Arm-c
- (2) VESA Plate-d
- (3) M5x14 Bolt-e
- (2) Nut-h
- (1) M10 Bolt-i
- (1) Support Plate-j
- (1) M10 Washer-k
- (1) Spring Washer-l
- (1) Grommet Base Plate-m
- (1) Wire Clip-n1
- (4) Wire Clip-n2
- (1) Allen Key-o
- (1) Wrench-p
- (8) M4x12 Bolt-q
- (8) M4x30 Bolt-r
- (8) M4 Spacer-s
Tools Required
Phillips Screwdriver
WARNING:
CAUTION!
This monitor desktop mount must be securely attached to the horizontal desk. If the mount is not properly installed, it may fall, resulting in possible injury and/or damage.
Step 1: Install the Pole to the Desktop
Option A: Weighted Base Install
1. Install the Pole (a) to the Weighted Base (b) using 3 M5x14 Bolts (e), and tighten using the Allen Key (o).
Illustration showing Pole (a) attached to Weighted Base (b) with Bolts (e) and Allen Key (o).
2. Optionally, drill a 10mm diameter hole in your desk and secure using the Support Plate (j), M10 Washer (k), Spring Washer (l), and M10 Bolt (i). Fasten the M10 Bolt with the provided Wrench (p).
Illustration showing the desk with a hole, where the Pole (a) is secured from underneath using Support Plate (j), Washer (k), Spring Washer (l), and Bolt (i), tightened with Wrench (p).
Option B: Grommet Base Install
Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.
1. Install the Grommet Base Plate (m) to the Pole (a) using 3 M5x14 Bolts (e), and tighten using the Allen Key (o).
Illustration showing Grommet Base Plate (m) attached to Pole (a) with Bolts (e) and Allen Key (o).
2. Position the Pole (a) on the mounting surface and secure using the Support Plate (j), M10 Washer (k), Spring Washer (l), and M10 Bolt (i). Fasten the M10 Bolt using the provided Wrench (p).
Illustration showing Pole (a) positioned on the desk surface, secured from underneath by Support Plate (j), Washer (k), Spring Washer (l), and Bolt (i), tightened with Wrench (p).
Self Drilled Grommet Hole Installation
1. Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8" (10mm) diameter hole at the marked position through the mounting surface.
2. Install the Grommet Base Plate (m) to the Pole (a) using 3 M5x14 Bolts (e), and tighten using the Allen Key (o).
Illustration showing Grommet Base Plate (m) attached to Pole (a) with Bolts (e) and Allen Key (o).
3. Position the Pole (a) on the mounting surface and secure using the Support Plate (j), M10 Washer (k), Spring Washer (l), and M10 Bolt (i). Fasten the M10 Bolt using the provided Wrench (p).
Illustration showing Pole (a) positioned on the desk surface, secured from underneath by Support Plate (j), Washer (k), Spring Washer (l), and Bolt (i), tightened with Wrench (p).
Step 2: Install Arm to the Pole
Install Swivel Arm (c) to the Pole (a). Fasten the bolt with the supplied Allen Key (o). Attach the Wire Clips (n1, n2) to the Pole (a) and Swivel Arm (c).
Illustration showing Swivel Arm (c) being attached to Pole (a) with Allen Key (o), and Wire Clips (n1, n2) being attached to the Pole and Arm.
Step 3: Attach the VESA Plate to the Monitor
For Monitor with Flat Back:
Illustration showing VESA Plate (d) being attached to the back of a monitor using Bolts (q) and Spacers (s).
For Monitor with Curved or Recessed Back:
Illustration showing VESA Plate (d) being attached to the back of a monitor using Bolts (r) and Spacers (s).
Step 4: Slide the Monitor onto the Head of Swivel Arm
Slide the monitor onto the head of Swivel Arm (c) as shown in the diagram.
Install the security Nut (h). Make sure the security nut is installed before you rotate the monitor.
Illustration showing the monitor with VESA plate attached sliding onto the Swivel Arm (c), followed by the installation of security Nut (h).
Step 5: Fix the Tilt Angle and Adjust the Level of Monitor
Fix the tilt angle:
Tighten the bolt with the supplied Allen Key (o) to fix the tilt angle.
Illustration showing Allen Key (o) being used to tighten a bolt to fix the tilt angle of the monitor arm.
Adjust the level of monitor:
If one monitor is lower, remove the Nut (h) and turn the bolt counter-clockwise with the supplied Allen Key (o) to raise the monitor. Install the Nut (h) after the adjustment. Ignore this step if monitors are level.
Illustration showing Nut (h) being removed, a bolt being turned counter-clockwise with Allen Key (o) to adjust monitor height, and then Nut (h) being reinstalled.
Step 6: Make the Necessary Adjustments and Manage the Wires
Use the supplied Allen Key (o) to make the necessary adjustments.
Manage the wires and store the Allen Keys (o) in Wire Clip (n1) for future use.
Illustration showing Allen Key (o) being used for final adjustments, and wires being managed and secured with Wire Clip (n1), storing Allen Keys (o).
