NAV-TV

Overview

The Ford 4" UNI-CAM kit interfaces an aftermarket rear camera into Ford vehicles equipped with the OEM 4" media screen. No dealership programming is required, and this kit is fully Plug & Play behind the factory media screen.

Kit Contents

The kit includes the following components:

• 4" UNI-CAM Module (NTV-ASY166)
• USB Cable (NTV-CAB009)
• Plug & Play T-Harness (NTV-HAR271)

Optional Reverse Cameras supported include F-Series/Flex CAM, CAM 6, CAM 7, and CAM 8.

Ford 4" UNI-CAM Pin Out

The following table details the pin assignments for the Ford 4" UNI-CAM:

Note: Any additional wires not mentioned here are not used for this installation.

Module Installation

1. Remove the 4" media screen from the dashboard, above the CD player.
2. Connect the provided Plug & Play T-Harness to the OEM Ford 12-pin plug previously connected to the radio.
3. After installing and running your reverse camera to the dash opening, connect your RVC signal to the RED RCA found on the Plug & Play T-Harness. Power your camera with an ACC source if planning to use the force camera feature (OUTPUT 1, 1 amp MAX).
4. Optional: If connecting a secondary (front) camera or AUX video source, connect the following:
   • Connect the front camera signal to the BLACK RCA from the 18-pin UNI-CAM harness.
   • Connect the rear camera signal to the YELLOW (female) RCA from the 18-pin UNI-CAM harness.
   • Connect the YELLOW (male) RCA to the BLACK RCA (may already be complete) from the screen side of the plug & play harness.
5. Optional: If adding a secondary (front) camera, connect INPUT 2 (Blue) to 12v through a toggle switch for activation. Sending 12v (+) to INPUT 2 will force the connected front image at any time.
6. Optional: If the user desires to force the rear camera at any time, connect INPUT 1 (Red) to 12v through a toggle switch for activation. Sending 12v (+) to INPUT 1 will force the connected rear image at any time.
7. Connect the UNI-CAM module to the 18-pin harness on the Plug & Play T-Harness.
8. Connect the male end of the Plug & Play T-Harness to the screen and proceed to the next section.

Ford 4" UNI-CAM Programming & Testing

Programming for the 4" UNI-CAM is automatic. After all connections are properly made and the module is connected, turn the car on to IGNITION, wait for the radio to fully boot and settle before testing functionality.

Notes:

• The radio may or may not visually reboot with a 'Diagnosis' message. It may appear that the radio just boots slowly (the first time, in which case it took programming before the display appeared).
• Place the car into reverse; the screen should automatically display the connected reverse image (or a blue screen if you have no video connected).
• This module VIN-LOCKS to the vehicle it is connected to and cannot be used on any other vehicle until it is De-Programmed. See De-Programming procedure below.

Ford 4" UNI-CAM De-Programming Procedure

Use this procedure if you wish to De-Program the 4" UNI-CAM from the car. This must be completed if you're removing the camera from the car, otherwise the screen will show an error while in reverse.

1. Leave the car's IGNITION in the OFF position.
2. With the module still connected to the vehicle, connect the PINK WIRE (input 3, pin 4) to 12v (+) temporarily.
3. Turn the IGNITION to ON.
4. The radio may or may not visually reboot with a 'Diagnosis' message. It may appear that the radio just boots slowly.
5. Place the car in reverse, confirm that the main radio image remains on the 4" display and does not show any error.
6. Disconnect the UNI-CAM system entirely and confirm once more that nothing happens while in reverse.

Ford 4" UNI-CAM Operation

• After all connections are made and programming is complete, placing the vehicle in reverse will automatically display the connected rear camera's image.
• If a forced rear camera is desired, connect input 1 (red) to 12v (+) through a toggle (not included), and the rear image will show whenever activated.
• If a front camera was added, force this camera by connecting input 2 (blue) to 12v (+) through a toggle (not included).

Installation Diagram

The installation diagram illustrates the connections between the vehicle's wiring harness, the UNI-CAM module, and the OEM Ford 4" screen. Key connections include:

• FROM CAR: Connections for Front Cam Power, 12v (+) ACC OUT, 12v (+) REV OUT, De-Program Wire, Force Front Input (+), and Force Rear Input (+).
• UNI-CAM Module: Outputs 1, 2, 3 and Inputs 1, 2, 3 are shown.
• Connections: Plug & Play T-Harness connects to the car and the UNI-CAM module. RCA connectors are used for Front CAM and Rear CAM video signals. A Male RCA is also shown.
• OEM FORD 4" SCREEN: Depicts a typical screen interface showing audio information (Artist, Song Title, Station, Volume, etc.).

Notes:

• Any wires not shown in the diagram are not needed for this installation.
• Not all wires shown will be used for every installation.
• If installing ONLY the rear camera, you may connect the signal directly to the 'Supplied RCA'.

Ford 4" Screen Compatibility List

This section lists part numbers for Ford 4" screens that are either compatible or incompatible with the UNI-CAM kit. Find the PART number on the back of the main 4" media screen.

Incompatible Display PART #'s

Compatible Display PART #'s

A sample label from the back of a Ford media screen is shown, indicating where to find the part number.

The product is Made in the USA ?? and the manufacturer, NAV-TV, is an ISO 9001 certified company. ⚙️