NAV-TV MyTouch F-CAM

Kit Contents

• VIM modules A & B (2x) NTV-ASY166
• USB cable (updates) NTV-CAB009
• Plug n' Play VIM Harness NTV-HAR241

VIM A Connector Pin Outs

(Diagram shows pin layout for wire side)

VIM B Connector Pin Outs

(Diagram shows pin layout for wire side)

VIM & F-CAM Installation

1. Remove the factory My Ford Touch radio. This requires removing panels and various 7 & 8mm screws. The trim panels securing the center radio bezel do not need to be fully removed, just moved out of the way.
   1. There are (2x) 7mm screws hidden beneath the airbag module; therefore, the airbag module must be popped out (no need to disconnect entirely). ⚠️ Apply tape for protection to the dashboard just beneath the airbag before you do this!
   2. Remove the passenger airbag assembly by removing the (3x) 8mm screws firing up from underneath the airbag. Access these screws by dropping the glove box down to the floor (again, no need to remove it entirely).
   3. Remove (or pop free at the right bottom corner) the cluster surround, and pull aside the trim pieces that surround the radio.
2. Remove the (4x) 7mm screws holding the screen in place.
3. Disconnect all wiring and set the screen aside.
4. Gather the Plug & Play harness from the F-CAM kit.
5. Plug the main LCD harness (male) from the car into the female side of the F-CAM Plug & Play harness.
6. Gather the ‘A’ and ‘B’ modules, and connect them to their prospective, labeled connectors.

Steps 7-11 are intended for F150 Raptor's only, those with an OEM front camera. If adding an aftermarket front camera to a standard F150, purchase NTV-KIT437 and refer to its instruction set (pg 5&6) before returning to step 12.

7. Under the driver's dash, make a small incision in the rubber harness grommet going through the firewall on the driver's side.
8. Connect a 10' pair of wires to the F-CAM module A: connect one wire to pin 6 and the other to pin 16. Route the free end of the wire pair through the firewall (at your incision) into the engine bay. Use silicon or 3M strip caulk to seal the incision.
9. On the underside of the hood, traveling down the driver's side, locate the camera harness. Cut the harness open at the bottom of the hood.
10. Locate the gray/violet wire and cut it in half.
11. Connect the extended wire labeled "Camera" (pin 6) to the camera side of the cut gray/violet wire. Connect the extended wire labeled “BCM” (pin 16) to the vehicle side of the cut gray/violet wire. Insulate and tape the connections when finished.

(Image description: A visual guide shows the process of cutting and connecting wires in the engine bay.)

12. Plug the male end of the Plug & Play harness into the factory LCD and test for proper operation (refer to pages 5 & 6 for operation instructions).

*Note: When the factory front camera is forced on, the active factory guidelines are not enabled. Only when the vehicle is in 4L will the active guidelines be available.

13. Optional: If you send 12v (through a toggle) to Input 2 (Blue), it will force the rear camera.
14. Optional: If you send 12v (through a toggle) to Input 3 (Orange), it will force VIM operation.

VIM & F-CAM (Raptor) Install Diagram

A block diagram illustrates the system connections. It shows two modules labeled 'A' and 'B' connected to the Ford LCD and the Car via a 'Plug n' Play Harness'. Module A is noted as 'Used for front factory cam only (F-Series Raptor)'. Connections are labeled 'BCM side' and 'Camera side', with 'Inputs/Outputs (refer to pinouts)'.

VIM & F-CAM Kit Operation

Video in Motion (VIM)

When VIM is activated, AUX video input can be viewed while the vehicle is in drive. This feature must be enabled every time the key is cycled.

To activate VIM: Press the Front Defroster Button 2 times within 1 second. Double-Tap ?

Additionally, if you send 12v (through a toggle) to Input 3 (Orange), it will force VIM operation.

Forced Rear Camera

This function allows the viewing of an aftermarket rear camera at any time.

To force rear camera: Press Rear Defroster Button 2 times within 1 second. Double-Tap ?

Additionally, if you send 12v (through a toggle) to Input 2 (Blue), it will force the rear camera.

Factory Front Camera Operation

The front camera can be viewed at any time using the factory procedure for activation.

*Note: Front camera will not display if VIM is enabled!

1. Using the steering wheel controls, scroll down to the "Truck Apps" function in the instrument cluster.
2. Scroll to the right until "Camera Disabled" is displayed.
3. Press the "OK" button on the steering wheel.
4. The front camera will display on the screen (active steering lines will not be displayed). The cluster will display 'Press OK to disable'.

To disable front camera:

1. Make sure the cluster is on the Camera options screen.
2. Press OK.

Agreement

End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only.