INSTRUCTION MANUAL
TARAMPS TAS 410F
400W MUSICAL
⚠ Installation of this product must be carried out by a qualified professional.
TAS 410F
ACTIVE BOX WITH 1 10 INCH SPEAKER
The TAS 410F active box was designed to reproduce low frequencies, known as sub-bass. Responsible for reproducing deep and impactful sounds in receiver systems with a frequency response of (10Hz to 250Hz), it guarantees accurate and natural audio reproduction throughout its entire range.
Technical Parameters
| Power | 400W Musical |
| Inch | 10 INCH |
| Input impedance | 2K Ohms |
| Sensitivity | 100 mV |
| Amplifier class | D |
| Frequency response (-3 dB) | 10 Hz a 250 Hz |
| Crossover LPF | 50Hz a 250Hz (-12dB/octave) |
| Resonance frequency | 29 Hz |
| Power tension | 90 a 240 Vac (AUTOMATIC) |
| Maximum consumption | 220Vac- 585W / 127Vac - 470W |
| Dimensions (AxLxP) | 339 x 322 x 403 mm |
| Acoustic components | 1 SPEAKER 10 INCH |
| Cone material | Polypropylene |
| Cabinet | Vented Box |
| Cabinet finishing | Laminate |
| Color | Black Ébony |
| Fabric finishing | Black Fabric |
| Cabinet weight | 13.7 Kg |
| Product Warranty | 12 Months |
Product Dimensions
The product dimensions are: Height: 339 mm (13.34 in) Width: 322 mm (12.67 in) Depth: 403 mm (15.86 in)
NOTE: To achieve better sound quality, it's important to position the back of your speaker close to the wall, at a distance between 10 and 20 centimeters.
Rear Panel Controls and Connections
The rear panel of the TAS 410F features the following controls and connections:
[Power Switch]: Labeled '0' (OFF) and '1' (ON).
SPEAKER OUT (4 OHMS): Output terminal for connecting an external passive speaker.
[Auto-On Mode Switch]: Labeled 'DIRECT ON' and 'AUDIO ON'.
[Low Pass Filter - LPF]: Rotary knob for adjusting the cutoff frequency from 50 Hz to 250 Hz. Includes MIN and MAX indicators, and a marker for 'HOME THEATER' use.
[Volume Control]: Rotary knob to adjust the input sensitivity. Includes MIN and MAX indicators.
[RCA Inputs]: Stereo RCA input jacks (L and R) for audio signals. The R input can also be used for Mono or LFE connection.
[Phase Switch 0/180]: Button to invert the phase of the audio signal by 180 degrees.
[Automatic Bivolt Indicator]: Shows the power supply status (127V/220V, 50-60Hz).
Detailed Control Descriptions:
- Power Cable: Connect the cable to the electricity network. This product operates with a power supply between 90 and 240 VAC.
- ON/OFF Switch: This switch puts the product on standby, ready to be turned on using the DIRECT ON / AUDIO ON mode.
- DIRECT ON / AUDIO ON:
- DIRECT ON: Turns the subwoofer on and off using the main power switch.
- AUDIO ON: With the switch in this position, the product turns on when it receives an audio signal and turns off automatically after approximately 10 minutes without audio.
- SPEAKER OUT: Output for connecting a 4 ohm passive speaker. (Example: TPS 408F passive Taramps Box)
- 0° / 180°: With the button pressed, inverts the phase of the audio signal by 180°. (Used to correct cancellation)
- LPF (Low Pass Filter): Variable adjustment of the maximum cutoff frequency from 50Hz to 250Hz. The point marked on the scale as "Home theater" is a suggestion for using the active box in a movie theater.
- Volume: Adjusts the amplifier's input sensitivity, which allows for perfect adjustment to the output signal levels of market players.
- INPUT (RCA): Audio inputs. Connect them to the RCA outputs of the audio reproduction system, using good quality shielded cables to avoid noise capture. For Mono or LFE connection, use the R input.
Starting The Subwoofer
Connect the receiver/pre output to the subwoofer input.
Connection Diagram Description: A diagram illustrates the connection between a 'RECEIVER OUT' (with L and R channels) and the subwoofer's 'INPUT' (with L, R, and MONO options).
Taramps
