Andeman Epower-B05 Multi-Function Jump Starter & Air Compressor
User Manual
Product Description
Please read this manual carefully and keep it properly before using this product for the first time. It will guide you to use it correctly and remind you of relevant precautions.
This product is a portable car jump starter and air compressor. It can start a car with a 12V battery that is losing electricity. It also inflates cars, motorcycles, bicycle tires, and balls. Additionally, it serves as a mobile power source for phones, tablets, PSP, MP3/MP4, cameras, and other digital electronic devices. The product includes LED light functions (lighting mode, SOS mode, warning mode).
Note: This product is not a toy and children are forbidden to use it.
Product Features
- ⚡ Engine Start
- ? Power Bank
- ? LED Light
- ? Air Inflation
- ? Car Tires
- ?️ Motorcycle Tires
- ? Bicycle Tire
- ⚽ Ball Supplies
Product Diagram
The device features the following components:
- Inflatable Tube Interface
- LED Light
- Type-C Charging Port
- USB 5V/2.1A Output
- USB 5V/9V/12V Output
- Jumper Cable Connection Port
- Digital Tube Display
- Air Pressure Set " + " Button
- "M" Button (Mode/Unit Switching)
- Power Button
- LED Light Button
- Air Pressure Set " - " Button
[Diagram description: A compact, rectangular device with a digital display on top showing pressure. Buttons for power, mode, pressure adjustment (+/-), and LED light are located on the front. Ports for charging and jumper cables are on the sides.]
Operation Guides
Charge Digital Products
1. Plug the USB port of the charging cable into the product's USB interface (Output 1 or 2).
2. Insert the other end of the charging cable into the corresponding charging port of the mobile phone or digital device.
3. Press and hold the "Power" button for 2 seconds to turn on the power; the USB power supply can then be started.
[Diagram description: Shows a USB cable plugged into the device and a phone.]
Car Jump Start
1. Remove the silicone plug and insert the EC5 connector of the jumper cable into the jumper cable connection port.
[Diagram description: Shows the EC5 connector being plugged into the device.]
2. Connect the red clamp to the positive pole (+) and the black clamp to the negative pole (-) of the car battery.
[Diagram description: Shows red and black clamps being attached to car battery terminals.]
3. Ignition within 30 seconds: Press the car start button or turn the ignition switch to the START position.
[Diagram description: Shows a car ignition key being turned.]
4. After successful startup, pull the plug of the wire clip from the product and remove the clip from the positive and negative terminals of the car battery.
Note: When starting the car, please make sure that the power of the product is above 50%.
Inflation Function
1. Charge The Product
Please fully charge the product before using it for the first time.
Charging: The units digit of the battery percentage value flashes (once per second). The screen displays the charging status.
Fully charged: Stop flashing and stop charging. The screen turns off after 10 seconds, and the device enters sleep state.
Note: The charging process will not be able to use this product for other functions.
[Diagram description: Shows the device plugged into a charger via USB-C, with the battery indicator flashing.]
2. Power On/Off
Press and hold the "Power" button (⏻) for 2 seconds to turn on the device. The battery percentage and the power icon (⏻) will be displayed on the screen, and the USB output function will be turned on simultaneously.
After booting, a single press of the "Power" button switches between starting and pausing inflation.
Press and hold the "Power" button again for 2 seconds to shut down.
If the product is turned on without any operation within 30 seconds, it will automatically shut down.
[Diagram description: Shows the device display with "100%" and the power button illuminated.]
3. Connect the Inflation Tube
For bicycles, electric bicycles, motorcycles, and cars, the inflation tube is usually connected directly.
[Diagram description: Shows the inflation tube connected to the device and a tire valve.]
4. Gas Nozzle / Gas Needle Mounting Method
For Air Beds and Swimming Rings:
1. Select a suitable air nozzle.
2. Connect the air nozzle to the inflation tube.
3. Inflate.
[Diagram description: Shows three steps for attaching a nozzle to the inflation tube.]
For Balls (Basketball, Football, etc.):
1. Use an air needle.
2. Connect the air needle to the inflation tube.
3. Inflate.
[Diagram description: Shows three steps for attaching an air needle to the inflation tube.]
5. Inflation Air Pressure
To ensure safety, before inflating, know the required air pressure value for the item. Check the item's surface information or instruction manual to avoid personal injury from over-inflation.
| Category | Types | Recommended Air Pressure Range |
|---|---|---|
| Car | Car tires | 2.2-2.8 Bar (32-40psi) |
| Motorcycle | Motorcycle, electric Motorcycle tires | 1.8-3.0 Bar (26-44psi) |
| Bike | Folding bicycle tires | 45-50psi |
| 12"14"16" bicycle tires | 30-50psi | |
| 20"22"24" bicycle tires | 40-50psi | |
| 26"27.5"29" bicycle tires | 45-65psi | |
| Ball | Basketball | 7-9psi |
| Football | 8-16psi | |
| Volleyball | 4-5psi | |
| Rugby | 12-14psi |
6. Preset Inflation Air Pressure
Mode Selection
Short press the "M" button (Ⓜ️) to select the inflation mode: "car", "motorcycle", "bicycle", or "ball". Long press the "M" button to switch between pressure units: PSI, BAR, KPA, Kg/cm².
- Car mode: Default 36psi (approx. 2.5bar)
- Motorcycle mode: Default 35psi (approx. 2.4bar)
- Bicycle mode: Default 45psi (approx. 3bar)
- Ball mode: Default 8psi (approx. 0.6bar)
After selecting the mode, the screen displays the default setting value and flashes three times per second. It then enters air pressure detection state. If the object is not connected, the air pressure value will display "0".
Adjust Presets
After selecting the inflation mode, short press the "+" or "-" keys (➕ / ➖) to adjust the preset air pressure value. Long press to quickly adjust.
After setting, the air pressure value flashes three times per second, and the setting is automatically confirmed.
Caution:
- When adjusting the preset value, the number flashes to indicate adjustment status. A steady number indicates real-time air pressure.
- The default value resets after switching modes or restarting.
- For swimming rings and air beds, adjust to "ball mode".
[Diagram description: Shows the device buttons with + and - for pressure adjustment.]
7. Inflation Instructions
Turn on inflation: After setting the air pressure, short press the "Power" button (⏻) to start inflation. The screen displays real-time air pressure changes.
Stop inflation: When the air pressure reaches the preset value, the pump stops automatically. You can also pause inflation by short pressing the "Power" button (⏻).
Shut down: In the power-on state, press and hold the "Power" button (⏻) for 2 seconds to shut down. The device will automatically shut down if there is no operation within 30 seconds to avoid accidental touch.
[Diagram description: Shows the power button with inflation controls.]
Special Reminders
- Inflation may generate 75-80dB noise.
- For items like balloons or toy balls with low inflation pressure, the automatic stop function may not engage. Use with caution.
- Prolonged use can cause the device and gas tube to heat up significantly. Avoid touching the hot tube. Allow to cool before continuing use. Be careful of burns when disassembling the gas nozzle; slight air leakage may occur.
- Increased pressure load and lower ambient temperatures may reduce the device's endurance.
- As the air pump generates heat, rest for at least 10 minutes after every 10 minutes of inflation before using it again.
8. Multifunctional Lighting
After the power is turned on, press the "LED light" button (?) to turn on the lighting mode. Short press again to cycle through SOS distress light mode, warning light mode, and then off.
Basic Parameters
| Parameter | Value |
|---|---|
| Brand | Andeman |
| Model | Epower-B05 |
| Size | 193 x 110 x 53mm |
| Inflation Pressure Range | 0.2~10bar / 3~150psi |
| Operating Temperature | Charge: 0℃~45℃, Discharge: -10℃~45℃ |
| Storage Temperature | -10℃~50℃ |
| Inflatable Tube Length | 435mm (Including gas nozzle) |
| Battery Capacity | 24000mAh (88.8Wh) |
| Working Noise | Less than 80dB away from 1 meter |
| Charging Input | Type-C 5V=3A |
| Charging Time | About 3.5 hours |
| USB Output 1 | 5V=3A, 9V=2A, 12V=1.5A |
| USB Output 2 | 5V/2.1A |
| Air Pressure Sensor Accuracy | ±1psi |
| Start Car Voltage | 12V |
| Peak Current | 4000A |
Precautions
Usage Notice
- This product is not a toy and is forbidden for children to use. Recommended for users over 16 years of age.
- When used for the first time, charge the product for more than 3 hours.
- This product has a built-in non-removable lithium battery. Do not throw it into fire or discard it carelessly. The lithium battery may catch fire, ignite spontaneously, and explode due to overheating, impact, or water. Avoid exposure to the sun in a car or high-temperature environments.
- If the product is swollen, leaking, or smells, stop using it immediately.
- If the product exhibits abnormal noise or high temperature during use, stop using it and shut it down immediately.
- Store or use in a dry and clean environment. Avoid dampness, heavy falls, water immersion, and sand intrusion. Sand and dust can damage the product. This product is not waterproof and must not be washed in water.
- Keep away from corrosive materials when storing. Storage temperature should not be lower than -10℃ or higher than 50℃. Extreme temperatures can shorten the product's life and damage the battery.
- Keep this product charged at least once every 3 months.
- Do not disassemble the machine yourself, as it may cause a safety accident.
Inflation Notice
- The product has a built-in DC motor that may generate electric sparks during operation. Do not use it in flammable or explosive environments.
- Before inflating, confirm the required air pressure value of the item to avoid personal injury from explosion due to over-inflation.
- When setting inflation pressure, ensure the measurement unit is selected correctly to prevent accidents like tire bursts. Common unit conversion: 1bar=14.5psi, 1bar=100kPa.
- Keep this product a safe distance from children when inflating objects.
- Do not bend or step on the inflation tube during inflation, and ensure airflow is unobstructed.
- Operators must not leave the scene during inflation. Observe the process to prevent over-inflation.
Jump Start Notice
- This product can start a 12V battery engine but not a 24V battery engine.
- Use the provided cord clamp to start the vehicle.
- Do not attempt to start the car if the product's power is lower than 50%, as it may damage the product.
- Do not clamp the battery clamps at both ends simultaneously, as this may cause a safety accident.
- If a startup fails, try again after at least 1 minute to avoid product damage.
- After starting the car, wait at least 30 minutes before charging the product.
Packing List
- Product ×1
- Jumper cable ×1
- Guide ×1
- Storage bag ×1
- Gas needle ×1
- Gas nozzle ×2
- Inflatable tube ×1
- Charging cable ×1
Note: The illustrations of products, accessories, and display interface in this manual are schematic diagrams for reference only. As the product is iteratively upgraded, the actual product may differ from the schematic diagram. Please refer to the actual product.
Trouble Shooting
| Problem | Elimination Method |
|---|---|
| Slow inflation | 1. Check battery power sufficiency. 2. Check for air leaks in the trachea. 3. Check if connecting parts at both ends of the trachea are tightly installed. 4. Check if the tires are flat. |
| Has been turned on, but cannot be inflated | 1. Check battery power sufficiency. 2. Check if the air pressure of the inflated item is higher than the preset value. |
| The inflation is normal, but the display pressure value is zero | Low-pressure inflated objects such as balloons are not within the measurable range of this device. |
| After installing the gas nozzle tightly, the power has been automatically turned off | It will automatically shut down if there is no operation within 30 seconds; just restart it. |
| There is air leakage when connecting the trachea | Install the trachea tightly. |
Disclaimer
- The company assumes no responsibility for problems caused by misoperation beyond the instructions.
- The company will not bear any responsibility if the product is damaged by disassembly and installation by oneself.
- If the use of a mismatched charger causes problems, the company assumes no responsibility.
- The company assumes no responsibility for products beyond the warranty period.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Contact Information
Thank you for your support of our original Audew products. Andeman has upgraded the original products, launched a more efficient jump starter, and enriched the product line by adding car repair and maintenance products. We hope that this brand can bring you a one-stop shopping experience for auto supplies and meet the needs of all users for auto supplies.
Contact Us: andeman@andeman.com
Importer Information
EU Importer
VISHTEC Itd
Address: 3rd floor office 5, Plovdiv, 2 Liuben Karavelov bul, 4002 Bulgaria
Email: compliance@vish-tec.com
UK Importer
VISHTEC UK Co.,Ltd
Address: 275 ISLINGTON SUITE, 1405 NEW NORTH ROAD, LONDON ENGLAND N1 7AA
Email: Vincent.feng@vish-tec.com
