Andeman TP07 Tire Pressure Monitor System
Model: TP07
Made in China ??
1. Description of Products and Accessories
Product Kits:
- Receiver: 1
- External Sensor: 4
- Nut: 4
- Spanner: 1
- USB Cable: 1
- User Manual: 1
- Adhesive Tape: 2
Host Components:
The main unit (Host) includes:
- Solar Pad ☀️ for charging.
- Micro-USB ? port for charging.
- LEFT BUTTON (POWER) ⚡ for turning the device on/off (long press).
- MENU ☰ button.
- RIGHT BUTTON ▶️.
Display Overview:
The display shows:
- Position of the tire (e.g., FL, FR, RL, RR).
- Pressure Unit (e.g., Bar, Psi).
- Temperature Unit (e.g., °C, °F).
- Current tire Pressure.
- Current tire Temperature.
- Power status.
Note: This product uses external sensors. The main components are 1 display, 4 sensors, 1 USB cable, and a user manual.
2. Shortcuts and Installation
Installation of Sensors:
- Screw out the tire valve dust cap.
- Insert the anti-dismantle gasket.
- Screw the sensor onto the corresponding tire valve position.
- Screw tight with the nut wrench.
- Check for leaks with soap water ?.
RESET: Press the left and right buttons simultaneously to reset all data to factory settings. Sensors are pre-paired at the factory and will automatically connect to the display when it enters the pairing page.
Tyre Matching (Re-pairing Sensors):
If sensors need to be re-paired (e.g., after tire rotation):
- In standby mode, long press the "MENU" button ☰ for 3 seconds to enter the system setting state.
- Press the "RIGHT SELECTION" button ▶️ 6 times to enter the pairing page (4 tire icons will appear).
- Short press the "M" (MENU) button ☰ twice to confirm entering the 4-round pairing page.
- Drive the car to 20 KM/H. The sensors will automatically pair.
Display Tire Pressure and Temperature:
The display shows tire pressure and temperature. Default units are BAR and °C. These can be changed in the settings.
Example Display: 31 2.51 Bar 34°C, 32 2.48 Bar 32°C.
Display Installation:
- Stick the display unit to a suitable location for the driver.
- When the display unit has low power, charge it using the Micro-USB ? port (Android Type). A cigarette lighter charger can be purchased separately.
3. Parameter Setting
When finished setting, press and hold the Menu button ☰ to save and exit.
Setting Function Details:
- Change Tire Pressure Unit: Long press the "M" button ☰ for 3 seconds. Select "bar" or "psi" using the "Left/Right" buttons ◀️▶️, then press "M" button ☰ to save.
- Change Tire Temperature Unit: Long press the "M" button ☰ for 3 seconds. Press the "Right" button ▶️ once, then press the "M" button ☰ once. Select "°C" or "°F" using the "Left/Right" buttons ◀️▶️, then press "M" button ☰ to save.
- Change Alarm Value of Tire Pressure: (Defaults: High pressure 3.1 Bar / Low pressure 1.8 Bar, High temperature 68°C). Long press "M" button ☰ for 3 seconds. Press the "Right" button ▶️ once, then press "M" button ☰ twice. The system will enter the alarm setting.
4. Special Operation
Change Upper and Lower Limits of Tire Pressure Value:
Factory defaults: High pressure 3.1 Bar / Low pressure 1.8 Bar, High temperature 68°C.
- In standby mode, long press the "MENU" button ☰ for 3 seconds to enter system settings.
- Press the "RIGHT BUTTON" ▶️ twice to enter the upper air pressure setting.
- Short press the "MENU" button ☰. The air pressure number will flash. Use the "LEFT/RIGHT" buttons ◀️▶️ to set the upper limit. Long press the "MENU" button ☰ to exit.
- To set the lower limit: In standby mode, long press the "MENU" button ☰ for 3 seconds, press the "RIGHT BUTTON" ▶️ 3 times to enter the lower limit setting. Short press the "MENU" button ☰. The air pressure number will flash. Use the "LEFT/RIGHT" buttons ◀️▶️ to set the lower limit. Long press the "MENU" button ☰ to exit.
Temperature Alarm Value Adjustment:
- In standby mode, long press the "MENU" button ☰ for 3 seconds to enter system settings.
- Press the "RIGHT BUTTON" ▶️ 4 times to enter the temperature alarm setting.
- Press the "MENU" key ☰ once. The temperature number will flash. Use the "LEFT/RIGHT" keys ◀️▶️ to set the temperature alarm value. Short press the "M" key ☰ to save.
5. Description of Monitor Function (Alarm Instructions)
When an alarm beeps ?, the corresponding icon on the display will flash.
| Alarm Type | Description | Action/Note |
|---|---|---|
| 1. Leakage Alarm | Slow Leak: Bi--Bi--Bi-- Fast Leak: Bi-Bi-Bi- |
Check if caused by nail or aging tire valve. |
| 2. High/Low Pressure Alarm | Alarm when Pressure Exceeds HI Limit (Default 3.1 Bar). Alarm when Pressure Exceeds LO Limit (Default 1.8 Bar). |
Bi-Bi-Bi--- |
| 3. High Temperature Alarm | Alarm when Temperature Exceeds HI Limit (Default 80°C). | Bi-Bi-Bi--- |
| 4. Display Low Power Alarm | When battery icon ? flashes, power will run out soon. | Please charge by Micro-USB ?, especially in rainy/cloudy weather. |
| 5. Sensor Low Power Alarm | Battery life depends on vehicle mileage. | Bi-Bi-Bi-Bi-Bi |
Quality Assurance:
For consumer rights, if there is a manufacturing process or component failure within one year from the date of purchase, free maintenance is provided with the essential warranty card.
6. Tire Exchange
In standby mode, long press the "MENU" button ☰ for 3 seconds to enter system settings. Press the "RIGHT SELECTION" button ▶️ 5 times to enter the tire exchange mode. Short press the "MENU" button ☰ to confirm. Two tire icons will flash.
Use the "LEFT/RIGHT" select keys ◀️▶️ to enter the tire exchange operation. The default is "left front wheel and right front wheel exchange". Short press the "LEFT/RIGHT SELECTION" keys ◀️▶️ to cycle through the following states:
- Left front wheel and right front wheel exchange.
- Left rear wheel and right rear wheel exchange.
- Left front wheel and left rear wheel exchange.
- Right front wheel and right rear wheel exchange.
- Right front wheel and left rear wheel exchange.
- Left rear wheel and right rear wheel exchange.
Press the "MENU" button ☰ once to confirm any two-round exchange combination. The exchange is successful.
Note: 0 = Front Left Wheel, 1 = Front Right Wheel, 2 = Rear Left Wheel, 3 = Rear Right Wheel.
Example Display States:
[Image Description: Display showing tire positions 0, 1, 2, 3 with associated pressure/temperature readings.]
[Image Description: Display showing tire positions 1 and 3 with associated pressure/temperature readings.]
[Image Description: Display showing tire positions 2 and 3 with associated pressure/temperature readings.]
7. Q & A
Fail to Connect with Tire Signal After Installation?
- When speed reaches 25 Km/hr, data will update automatically.
- If there's a mismatch between the display and sensors, please re-match correctly.
One Tire Signal Missing?
- Check and re-match the tire on that position.
- Check if the sensor on that position is broken.
No Image on Display?
- Check if the display is powered on.
- Use Micro-USB ? to charge the device.
Precautions and Statements:
- Please install sensors after the monitor is on.
- This device can be used on cars not originally equipped with TPMS, with a tire pressure limit within 3.50 Bar. It works best with a 12V accumulator.
- Stop the vehicle safely when an alarm is beeping ?.
- This device cannot detect sudden tire damage.
- Do not operate the device while driving.
- Battery life of sensors depends on vehicle mileage.
- Please park the vehicle in a safe place if any theft occurs. The manufacturer shall take no responsibility.
- Tire temperature and pressure will increase (0.1-0.3 Bar) when driving.
8. Technical Parameters
Parameter of External Sensor:
| Parameter | Value |
|---|---|
| Working voltage | 2.1V-3.6V |
| Storage temperature | -30℃ to 85℃ |
| Working temperature | -40℃ to +125℃ |
| Temperature accuracy | ±2℃ |
| Working pressure | 0-3.5Bar |
| Pressure accuracy | ±0.1Bar |
| IP Rating | IP67 |
| Transmit power | ≤5dBm |
| Transmit frequency | 433.92MHz |
| Dimension | ≥23mm (diameter) x 17mm (high) |
| Weight | 8.0g |
9. Names of Toxic and Hazardous Substances
This form is made under the Rule of J/T 11364-2014.
| ITEMS | Pb | Hg | Cd | Cr6+ | PBB | PBDE |
|---|---|---|---|---|---|---|
| PCB | X | ○ | ○ | ○ | ○ | ○ |
| Plastic | ○ | ○ | ○ | ○ | ○ | ○ |
| Metal | X | ○ | ○ | ○ | ○ | ○ |
| Battery | X | X | ○ | ○ | ○ | ○ |
| Accessory | X | ○ | ○ | ○ | ○ | ○ |
Symbol Key:
- X: Indicates that the hazardous substance exceeds the limit specified by GB/T 26572 in at least a homogeneous material of the part.
- ○: Indicates that the hazardous substance does not exceed the limit specified by GB/T 26572 in the part.
Environmental Protection Use Period: This Mark presents the Environmental Protection Use Period of the device if no other special note. Some changeable parts may have different periods, such as the battery unit module. Generally, the Environmental Protection Use Period is 10 years ♻️.
10. Contact Us
If you have any suggestions, you can send feedback by sending a message to andeman@andeman.com or contacting the after-sales staff through the shopping interface.
FCC Regulatory Compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
