Andeman WS1 EV Wall Charger
Model: WS1 - User Manual
Before operating this product, please read the enclosed Operating Instructions completely.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric products, basic precautions should always be followed, including the following. This manual contains important instructions for Models WS1 that shall be followed during installation, operation and maintenance of the unit.
- Read all the instructions before using this product.
- This device should be supervised when used around children.
- Do not put fingers into the electric vehicle connector.
- Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation, or any other signs of damage.
- Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.
- Caution - To reduce the risk of fire, connect only to a circuit provided with 60 amperes maximum branch circuit over-current protection in accordance with the NEC.
- This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The power cord for this product has an equipment grounding conductor and a grounding terminal. The terminals must be connected to the corresponding correct port and must be properly installed and grounded in accordance with all local codes and ordinances.
- WARNING - Improper connection of the equipment-grounding conductor is able to result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the terminals supplied with the product - If the terminals do not match the electrical box, have a qualified electrician install a suitable outlet.
SAVE THESE INSTRUCTIONS
Operating Precautions
Before the operation, please read the operation manual carefully to know the equipment and the correct method of use. Please keep it for future reference.
- Before installation, please check the grid for the Level II 240 v ~ ±10% (60 Hz). Otherwise, it may be unusable.
- Do not use flammable, explosive, or combustible materials, chemicals, combustible gas, and other dangerous goods near the charging pile.
- Keep the charging point dry and clean. If there is any dirt, please use a clean, dry cloth to wipe it. It is forbidden to touch the point pin.
- Hybrid cars should be recharged after the engine has stopped. Vehicle driving is prohibited during the charging process.
- Children should not get close to the charging process to avoid harm.
- In case of rain, thunder, or severe weather, please charge with caution. It is strictly prohibited to use a charging cable that is broken, worn, or has exposed wires. If the charging pile is obviously knocked down or damaged, please stay away from the charging post immediately and contact the staff.
- If a fire, electric shock, or other abnormal situation occurs during charging, immediately press the stop button to ensure personal safety.
- Please do not attempt to remove, maintain, or modify the charging pile. Improper use may cause damage, leakage, and so on.
Product Introduction
The EV AC charging pile is designed to address the pain points of the charging pile industry. It features convenient installation and debugging, simple operation and maintenance, accurate measurement, and perfect protection functions. It has good compatibility and meets the charging requirements of the SAE J1772 standard. This AC pile has a protection grade of Type 4, with good dust-proof and waterproof functions, making it suitable for safe indoor and outdoor operation.
Product Parameters
| Type no. | EV-WS1 |
| Input voltage | Level II 240V~±10%(60Hz) |
| Output voltage | Level II 240V~±10%(60Hz) |
| Power output | 12 KW |
| Maximum output current | 50A |
| Class of protection | NEMA Type 4 |
| Protection Function | Over / under voltage protection, over current protection, Current leakage protection(CCID20), grounding detection protection, emergency stop protection |
| Indicator light | Standby - blue on; Charging - green blinking; Alarm - red on |
| Indication of status | 4.3-inch |
| Mode of charging | Swipe card charging / APP charging / Appointment charging |
| Charging interface | SAE J1772 |
| Material of case | PC+ABS |
| Operating temperature | -30 °C~50 °C |
| Storage temperature | -40 °C~80 °C |
| Relative humidity | 5% to 95% no condensation |
| Overall dimensions | 333*213*92mm(H*W*D) |
Product Overview
The EV Wall Charger features:
- Swipe card area
- Status indicator ring
- Display screen
- Charging cable/wire mount
- Emergency stop button
- Charging gun
Installation Instruction
List of Parts
General purpose accessories
| Product specification | Ac pile instruction manual | 1 copy |
| RFID card | M1 card | 2 pcs |
Wall mount installation
| Expansion screw | M8*60 expansion screw | 4pcs |
| Wall hanging fixed plate | Mounting the chassis | 1 pc |
| Expansion screw | M6*40 expansion screw | 3 pcs |
| Charging cable hook | Plastic hook | 1pc |
1. The installation method is wall hanging
- Take out the mounting plate of the charging pile from the bottom of the device and carefully check the mounting size of the screw holes.
- Select the parking space where the charging pile is to be installed. The lowest position of the fixing plate of the charging pile should be 120cm above the ground. [Diagram showing a wall with a height marker of 120cm and an EV.]
- Drill four M8 diameter holes according to the positions of the screw holes in the fixing disk, knock in the expansion rubber plugs, and secure the mounting disk with nuts on the fixing chassis. Fix the bottom plate on the wall or support (pay attention to the installation direction, installation in the direction of the arrow). [Diagram showing drilling holes, inserting plugs, and mounting the plate.]
- For the charging gun/cable storage bracket, please refer to the following installation steps: Step 1: Drawing of fixing holes. Step 2: Drilling with tools. Step 3: Insert the expansion tube and screw it in. [Diagrams illustrating the steps.]
2. Wire Connection Instructions
A power distribution box is used. The L(Red), L(Black), PE (Green&Yellow) ends of the input cable of the plug correspond to the L1, L2, and PE ends of the circuit breaker, respectively. [Diagram showing wire connections to a circuit breaker and the charging unit.]
3. Hang the charging pile on the bottom plate, charger gun cord hang on the plastic hook
[Image of the wall-mounted charger with the cable neatly hung on the hook. A measurement indicates 120cm / 47.24inch from the bottom of the charger to the ground.]
MOBILE PHONE APP CHARGING OPERATING INSTRUCTIONS
1. APP download and binding use
a. To download the smart APP, enter the following address in the mobile browser: https://developer.tuya.com/cn/docs/iot/tuya-smart-app-smart-life-app-advantages?id=K989rqa49rluq. Click the website and follow the prompts to install.
b. QR code download: Open the mobile browser or other social software, scan the QR code, and follow the APP prompts. [QR code image.]
2. Binding and Using Devices
Step 1: Open the installed APP, click 'Agree' to the privacy statement. You can register with your mobile phone number or bind with social software. Log in to the APP after successful registration. Enable Location, Bluetooth, and Wi-Fi on your mobile phone. If the charging device is in standby state, the APP will automatically search for the charging device, and the device name will be displayed. [Image of the app requesting permissions for Data Analysis and Personalization, with a 'Go to App' button.]
Step 2: Click 'Add device' to enter the Wi-Fi pairing interface. The APP will automatically identify the Wi-Fi name of the phone. Click 'Next', and the device will be automatically bound. After successful binding, a message will be displayed indicating that the device has been successfully added. Finally, click the 'Finish' icon and wait about 5 seconds for the device to be bound. [Diagrams showing the 'Add Device' interface, searching for devices, and a success message.]
You can also click '+' in the upper right corner of the APP to manually add the device. Select the category 'Energy' in the left column, pull up the device type, find 'Car charging pile (Bluetooth + WIFI)', click to enter, follow the prompts, click 'Confirm if the indicator light is flashing', then click 'Quick flashing' again. [Diagram showing the app's device categories and types, including 'EV charger (BLE+Wi-Fi)'.] [Diagrams illustrating the process of resetting the device and selecting indicator light status: 'Blink Slowly' or 'Blink Quickly'.]
Step 3: Enter the Wi-Fi password connected to the mobile phone and click 'Next' to match the password. Always set the bound device as prompted. [Screenshots showing Wi-Fi selection, password entry, and device binding success.]
Step 4: After binding the device, charge it according to the APP interface. The application also supports the functions of 'adjusting current' and 'delayed charging'. [Image showing the 'All Devices' list in the app.]
APP FUNCTION
Charging mode function
Click 'Charging mode' to switch between real-time charging and delayed charging mode (appointment charging mode). You can set an appointment to delay charging for a period of 1-12 hours. [Screenshots of the app showing 'Charging mode selection' with options for 'Real-time charging' and 'Delayed charging' with a time selection.]
Adjust charging current
Click 'Setting' into 'Charging current'. Slide up and down to set the charging current. [Screenshots of the app showing current settings from 48A to 52A.]
Record of charging
Click 'Charge record export' to check the charging record and power record. [Screenshots of the app showing charging details like current temperature, positive total active power, and a list of charging sessions with time and energy consumed.]
CHARGING INSTRUCTIONS
1. Make sure the charging pile is properly connected to the power supply. After the device is powered on, it enters the standby state. The device display interface is shown below: [Diagram of the charging pile in standby mode.] [App screen showing 'Welcome to use AC charging equipment. Plug in your gun for charging.']
2. Adjust the time: Select an appointment time. Set power: Slide up and down to set charging power. [App screens showing 'Charging mode selection' and 'Charging current' adjustment.]
3. Plug in the charging connector to the vehicle inlet of the car. The device display interface is shown below right side: [Diagram of plugging the charging connector into a car.] [App screen showing 'Welcome to use AC charging equipment. Swipe card to start charging.']
4. Swipe the card on the logo to start charging. The device display interface is shown below: [Diagram of swiping an RFID card.] [App screen showing 'In the charging' status with details like charging time, voltage, current, power, and battery level.]
Note: If the card stays on the logo area for more than 15s, the charging station enters plug-charge mode. In this mode, the charging station will start without swiping the card. When you swipe the card again for 15s, it will switch back to swipe mode, and you will need to swipe the card before charging.
5. The station will stop charging when your car is fully charged. You can click the APP or swipe the card to end. [App screen showing 'End of the charging' status.]
6. After charging is complete, unplug the charging gun and place the dust cover onto the charging connector. [Diagrams showing unplugging the gun and placing the dust cover.]
STATUS INDICATOR
Charging indicator LED indicator status table
| Three color indicators status | blue light: standby |
| green light: charging | |
| red light / purple light: failure | |
| Standby | steady blue light |
| Connected | steady green light |
| Charging | green light flashing; Green Breathing Lighting |
| CP fault | steady red light |
| Over voltage or under voltage | the red light blinks once every 1S |
| No ground wire | the red light blinks once every 2S |
| Emergency stop | the red light blinks once every 4S |
| Over current | the red light on for 3s, off for 3s |
| Electric leakage | the purple light blink once every 1S |
| Over temperature | the purple light blink once every 2S |
| Relay adhesion | the purple light blink once every 4S |
COMMON PROBLEMS AND SOLUTIONS
| Problems | Cause | Solution |
| The Display is black (LED indicator is off) | The AC inlet switch is not closed, and the AC inlet switch is tripping. | Close the AC incoming wire switch again. If it trips all the time, please check whether the wiring of the equipment is correct and the L or N wire is connected to the L1,L2 terminal. |
| Controller Boot Failure | The gun is not inserted properly; During the charging process, someone pressed a button on the charging handle. | Put the gun back in place; Strengthen supervision after normal charging to prevent someone from pressing the handle button during charging. |
| End lock gun | The WIFI signal network is unstable, and unlocking failed. Vehicle communication problem. | Turn off the car starting key, turn off the engine and lock the car, and then restart the car. If the problem cannot be solved, please contact the car dealers! |
| Symptom Possible causes | AC input voltage too high | 1. If the voltage exceeds 265Vac for a short time, wait for the power grid to restore itself to the normal voltage range. 2. Check the background monitoring data and analyze. If the voltage in this area is overvoltage for a long time, adjust the input overvoltage protection point to 265Vac by configuring software. |
| AC undervoltage | AC input voltage too low | Check the background monitoring data and analyze. If the voltage in this area is chronically undervoltage (175Vac), the protection point of input undervoltage can be adjusted to 90Vac at least by configuring software. |
| AC overcurrent | Excessive AC input current | 1. Immediately turn off the leakage/overcurrent protection circuit breaker of the power distribution box. 2. Check whether there is low impedance or short circuit between the output line of AC pile. 3. After the fault is rectified, power on the device again. If the fault persists. |
| Overtemperature | The temperature in the AC pile is too high | Check the AC pile installation environment. Check whether there are other heating devices nearby. Ensure that the ambient temperature is below 50 °C. |
| Current cannot reach the set or defined value | 1. Using an adapter 2. Vehicle is set for charging current 3. The vehicle's power is relatively full (more than 90%) 4. Setting of the current level of the charging pile |
1. If the adapter is used, please check whether the rated working current of the adapter is matched; 2. If the vehicle can set the charging current, please check whether the vehicle setting current gear is matched; 3. If the vehicle's power is relatively full (more than 90%), the vehicle may reduce the charging current, which is normal; 4. Check whether the current gear of the charging pile is set correctly, you can check the set current gear through APP. |
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Importer Information
EU importer
VISHTEC Itd
Address: 3 rd floor office 5, Plovdiv 2 Liuben Karavelov bul, 4002 Bulgaria
Email: compliance@vish-tec.com
UK Importer
VISHTEC UK Co.,Ltd
Address: 275 ISLINGTON SUITE 1405 NEW NORTH ROAD LONDON ENGLAND N1 7AA
Email: Vincent.feng@vish-tec.com
[FCC logo] [Recycling logo] MADE IN CHINA
Related Documents
 |
Andeman WS-40S EV Wall Charger User Manual User manual for the Andeman WS-40S EV Wall Charger, detailing safety instructions, installation, app usage, charging operations, status indicators, troubleshooting, and certifications. |
 |
Andeman EV Portable Charger HS1 - ENERGY STAR Certified Specifications Detailed specifications and ENERGY STAR certification information for the Andeman EV Portable Charger model HS1, including input/output power, connectivity, and operational test results. |
 |
Andeman Epower-B05 Multi-Function Jump Starter and Air Compressor User Manual Comprehensive user manual for the Andeman Epower-B05, a multi-function jump starter, air compressor, and power bank. Includes operating instructions, features, specifications, troubleshooting, and safety precautions. |
 |
Andeman Epower-155 Pro Multi-Function Jump Starter User Manual User manual for the Andeman Epower-155 Pro, a powerful 3000A multi-function jump starter and power bank. Find detailed instructions on jump-starting vehicles, charging the device, using the LED light, specifications, safety precautions, and troubleshooting tips. |
 |
Andeman Epower-177 Multi-Function Jump Starter User Manual Comprehensive user manual for the Andeman Epower-177 multi-function jump starter, covering product overview, specifications, usage instructions, safety guidelines, and troubleshooting. |
 |
Andeman TP07 Tire Pressure Monitor System: Instruction Manual & Features Detailed instruction manual for the Andeman TP07 Tire Pressure Monitoring System (TPMS). Covers product kits, installation, setup, tire matching, special operations, alarm functions, troubleshooting, technical parameters, and safety compliance. |
 |
Andeman JS-108B Smoke Leak Detector User Manual Comprehensive user manual for the Andeman JS-108B Automotive Smoke Leak Detector. Learn about its features, operation, maintenance, and safety instructions for efficient vehicle leak detection. |
 |
BM550 Battery Tester User Manual and Specifications Comprehensive guide for the Andeman BM550 Battery Tester, detailing its features, usage instructions for 6V, 12V, and 24V batteries, test result interpretation, and technical specifications. Covers SOH, SOC, voltage, and internal resistance testing for automotive batteries. |