Arenti VBELL 1 QUICK GUIDE

Quick Start Guide

Sections:

• Packing list
• Product description
• Installation
• Product configuration
• Legal notice

1. Packing List

• Camera: 1X (Image of the camera unit)
• Power adaptor: 1X (Image of the power adaptor)
• USB cable: 1X (Image of the USB cable)
• Chime: 1X (Image of the chime unit)
• Screws: 3X (Image of screws)
• Screwdriver: 1X (Image of a screwdriver)
• Warning sticker: 1X (Image of a warning sticker)
• 3M sticker: 2X (Image of 3M adhesive stickers)
• Quick guide: 1X (Image of a quick guide booklet)
• Bracket: 1X (Image of the mounting bracket)

* The bracket is attached to the camera.

2. Product Description

Camera Unit:

Numbered components:

• 1. Microphone
• 2. Lens
• 3. PIR (Passive Infrared sensor)
• 4. Doorbell button
• 5. Speaker
• 6. LED indicator
• 7. SD card slot
• 8. Reset button
• 9. DC5V USB port
• 10. Device ON/OFF switch

Chime Unit:

Numbered components:

• 1. LED indicator
• 2. Speaker
• 3. Ringtone
• 4. Volume control
• 5. Function button
• 6. Micro USB port

Device Reset:

To reset the device, press and hold the reset button for 5 seconds. The camera will beep upon completion.

LED Indicator Status:

Camera LED Indicator:

Chime LED Indicator:

3. Installation

Installation with Screws:

1. Fix the mounting bracket to the wall using the provided screws.

2. Install the camera into the bracket and secure it with the screw at the bottom.

Installation with 3M Stickers:

1. Lock the bracket to the camera using the screw at the bottom.

2. Apply the 3M adhesive tapes to the bracket.

3. Stick the other side of the adhesive tapes to the wall.

4. Product Configuration

1. Turn on your camera.
2. Connect your smartphone to the Wi-Fi network.
3. Download the Arenti app from the App Store or Google Play, depending on your device.
4. Launch the App and sign up for the first use.
5. Follow the on-screen instructions to add your camera.

Chime Pairing

Notice: If you have multiple cameras, repeat step 5 to add devices one by one. To change the Wi-Fi network, restore the camera to factory settings and follow step 5.

1. Short press the [settings icon] (within 2 seconds). The status light on the chime will flash red slowly, indicating it is in pairing mode. (During pairing mode, the chime will blink red).

2. Press the doorbell button to initiate pairing. Pairing is successful when the chime status light turns off and the song plays automatically.

Description:

• The chime can connect to a maximum of eight doorbells.
• To exit pairing mode, press the [settings icon] again (within 2 seconds) while the chime is in pairing mode.
• After successfully adding a chime, the volume will automatically adjust to maximum. If the volume is at its minimum, pressing the [music note icon] will return it to the maximum volume.
• Each press of the [music note icon] will play the next song, accompanied by a blinking blue light. (When playing a ringtone, the chime will blink blue).

Specifications

5. Legal Notice

Support

Visit: www.arenti.com

Symbols

• Direct current (DC)
• Symbol for battery disposal: Do not throw batteries or out-of-order products with household waste. Dangerous substances may harm health or the environment. Return these products to your retailer or use the selective collection service proposed by your city.
• CE mark: Hereby, Arenti declares that the radio equipment type 'VBell 1' is in compliance with Directive 2014/53/EU. The full test of the EU declaration of conformity is available at the following Internet address: www.arenti.com
• [house icon] For indoor use only