Caséta by Lutron Quick-Start Guide

Product Information

Product: In-wall dimmer

Model: Diva Smart Dimmer DVRF-6L

Model Number: DVRF-6L

Voltage: 120 V~50/60 Hz

For installation videos, visit: www.casetawireless.com/support

Contents Supplied

• In-wall dimmer (DVRF-6L)
• Wire connectors (5)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Phillips-head screwdriver

Installing Your Dimmer (Single Pole Installation)

Step 1: Turn Off Power

WARNING: SHOCK HAZARD

May result in serious injury or death. Turn off power at the circuit breaker or fuse before installing.

Step 2: Remove Existing Switch

Remove the wallplate from the switch. Remove the existing switch and pull it away from the wall.

Disconnect all three wires from the switch.

Step 3: Ganging and Derating

Important Note: Multi-gang installations may reduce the dimmer's maximum wattage rating. See the chart below for maximum wattage information.

For maximum wattage information when mixing light bulb types, see www.casetawireless.com/ganging.

Step 4: Connect the Dimmer

Grounding: Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a supplied wire connector.

Line/Load: Connect either of the remaining wires from the wallbox to the black wire on the dimmer using a supplied wire connector.

Load/Line: Connect the remaining wire from the wallbox to the red wire on the dimmer using a supplied wire connector.

Unused Wire: Cap the blue wire coming from the dimmer with a small supplied wire connector. The blue wire is not used for single pole installations.

Note: Wire colors depicted in this guide may not match what is in your walls.

For installation instructions when two or more switches control a light (3-way or 4-way), visit www.casetawireless.com/3way.

Step 5: Mount the Dimmer

Use the screws provided to mount the dimmer.

Step 6: Attach the Wallplate

Attach the adapter to the dimmer using the screws provided and snap on the wallplate.

Step 7: Turn Power On

Turn power on at the circuit breaker.

Compatibility

Works with energy-efficient dimmable light bulbs:

• LED: up to 150 W
• CFL: up to 150 W
• Halogen: up to 600 W
• Incandescent: up to 600 W

Note: Dimmable LED and CFL light bulbs vary in their dimming performance. If they flicker or turn off, visit www.casetawireless.com/lowend for information on adjusting the dimmer. For a complete list of compatible bulbs, visit www.casetawireless.com/bulblist.

Using Your Caséta Wireless System

With a Smartphone or Tablet (Smart Hub Required)

The Caséta Wireless Diva Smart Dimmer can be controlled from a smartphone when used with the Lutron Smart Hub (Smart Bridge) and the Lutron app.

Setup Steps:

1. Download the Lutron app (Search for "Lutron Caséta"). Available on the App Store and Google Play.
2. Launch the Lutron app. The app will guide you through setting up your devices.
3. Use the Lutron app to complete all remaining steps, such as adding devices, Pico remotes, setting up controls, scheduling, and connecting while away.

Without a Smartphone or Tablet (Smart Hub Not Required)

Pairing the Dimmer and Pico Remote Control

Step 1: Press and hold the "off" button on the dimmer for 6 seconds until the light bar starts blinking.

Step 2: Press and hold the "off" button on the Pico remote control for 6 seconds until the lights flash 3 times.

Changing the Favorite Light Level on the Pico Remote Control

You can use the round "favorite" button on the Pico remote control to recall a favorite light level. We've set it to 50%, but you can change it.

Step 1: Set the desired light level on the dimmer using the slider.

Step 2: Press and hold the "favorite" button on the Pico remote control for 6 seconds until the light bar blinks twice on the dimmer. The new favorite level is now saved.

Using Your Controls

In-Wall Dimmer

• On: Press the top button to turn lights on.
• Dim/Brighten: Adjust the slider to dim or brighten the light level. The slider will not turn lights off.
• Off: Press the bottom button to turn lights off.
• Favorite: Press the center button to recall the saved favorite light level.

Replacing Light Bulbs Using FASS

Pull the FASS (Front Accessible Service Switch) switch out on the in-wall dimmer to remove power at the light socket.

Troubleshooting

For additional troubleshooting suggestions, go to www.casetawireless.com/support.

Important Cautions and Information

Cautions

Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.

Electrical Codes

Install in accordance with all national and local electrical codes.

Grounding: When no "grounding means" exist in wallbox, the National Electrical Code (NEC) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.

FCC/IC Information

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Warranty Information

For warranty information, please visit www.casetawireless.com/warranty.

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).