Lutron Caséta Wireless In-Wall Dimmer Quick Start Guide

Introduction

Welcome to Caséta™ Wireless. This guide provides instructions for installing and using your Caséta™ Wireless in-wall dimmer.

Double Your Warranty: Share your feedback and extend your warranty by 1 year at www.casetawireless.com/register.

Contents Supplied

• In-wall dimmer (PD-6WCL)
• Wire connectors (3)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Pliers
• Phillips-head screwdriver

Compatibility

Works with energy-efficient dimmable light bulbs:

• LED: up to 150 W
• CFL: up to 150 W
• Halogen: up to 600 W
• Incandescent: up to 600 W

Note: Dimmable LED and CFL bulbs may vary in performance. Visit www.casetawireless.com/lowend for adjustment information. For a full list of compatible bulbs, visit www.casetawireless.com/bulblist.

Installation: Lights with One Wall Switch (Single Pole)

1. Turn Power Off

   ⚠️ SHOCK HAZARD. Turn off power at the circuit breaker or fuse before installing.

2. Remove Existing Switch

   Remove the wallplate. Remove the switch and pull it away from the wall. Disconnect all three wires* from the switch.

   *If your switch has more than 3 wires, see the video at www.casetawireless.com/3way.

3. Prepare Dimmer (Remove Side Sections if Necessary)

   Bend back and forth to remove side sections. Do not remove outer side sections on dimmers at the end of a gang. Removing side sections reduces the maximum wattage rating.

   Maximum Wattage Derating Chart (120 V~ 50/60 Hz)

   Side Sections Removed	LED & CFL	Incandescent & Halogen
   None	150 W	600 W
   1 side	150 W	500 W
   2 sides	150 W	400 W

   For wattage information when mixing bulb types, see www.casetawireless.com/ganging.

4. Connect the Dimmer

   1. Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector. ? [Ground wire]
   2. Connect one of the remaining wires from the wallbox to one of the remaining wires on the dimmer using a second wire connector.
   3. Connect the other wire from the wallbox to the remaining wire on the dimmer using a third wire connector.

5. Mount the Dimmer

   Use the provided screws to mount the dimmer.

6. Attach the Wallplate

   Attach the adapter to the dimmer using the screws provided and snap on the wallplate. If installing next to other devices, ensure the wallplate has the correct number and size of openings.

7. Turn Power On

   Turn power back on at the circuit breaker.

⚠️ CAUTION: Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent lamps. Do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.

Codes: Install in accordance with all national and local electrical codes.

Grounding: If no "grounding means" exist in the wallbox, the NEC allows installation if a nonmetallic faceplate is used or the circuit is GFCI protected. If using these methods, cap or remove the green wire before screwing the control into the wallbox.

FCC/IC Information: This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) it must accept any interference received. Modifications not expressly approved by Lutron Electronics Co., Inc. may void the user's authority to operate the equipment.

Using Your Caséta™ Wireless Kit (Sold Separately)

With a Smartphone or Tablet (Smart Bridge™ Required)

Control your lights from a smartphone or tablet when used with the Lutron® Smart Bridge™. Follow these instructions:

1. Download the Lutron® App

   Search for "Lutron Caseta" on the Google Play Store or Apple App Store.

   Android App | Apple App Store

2. Launch the Lutron® App

   The Lutron® app will guide you through setting up your devices.

3. Complete Setup

   Use the app to add devices (Pico® remotes, dimmers, shades), control lights three ways, schedule lights, and connect remotely.

Without a Smartphone or Tablet (Smart Bridge™ Not Required)

Pairing the Dimmer and Pico® Remote Control

1. Press and hold the "off" button on the dimmer for 6 seconds until LEDs start blinking. ▶️ [Start Pairing]
2. Press and hold the "off" button on the Pico® remote control for 6 seconds until its lights flash 3 times. ⚡ [Pairing Signal]
3. Repeat steps to pair other Pico® remote controls.

Changing the Favorite Light Level on the Pico® Remote Control

Use the round "favorite" button on the Pico® remote control to recall a favorite light level. The default is 50%, but you can change it.

1. Set the desired light level on the dimmer.
2. Press and hold the "favorite" button on the Pico® remote control for 6 seconds until the dimmer's LEDs blink twice. The new favorite level is now saved. ✔️ [Favorite Saved]

Using Your Controls

In-Wall Dimmer

• On/Off: Press the top or bottom of the paddle.
• Brighter: Press the top of the paddle. ⬆️ [Brighter]
• Darker: Press the bottom of the paddle. ⬇️ [Darker]
• Favorite: Press the center "favorite" button (if configured). ⭐ [Favorite]

Pico® Remote Control

• On: Press the top button.
• Favorite: Press the center button. ⭐ [Favorite]
• Brighter: Press the right side of the top button. ⬆️ [Brighter]
• Darker: Press the left side of the top button. ⬇️ [Darker]
• Off: Press the bottom button.

FASSTM Front Accessible Service Switch: Pull this switch out on the in-wall dimmer to remove power at the light socket for bulb replacement.

Troubleshooting

For additional troubleshooting suggestions, visit www.casetawireless.com/support.

Device Ratings

In-wall dimmer: PD-6WCL, 120 V~ 50/60 Hz

? Important Notes:

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).