Lutron Caséta Wireless In-Wall Dimmer Quick-Start Guide

Introduction

Welcome and thank you for purchasing a Caséta™ Wireless in-wall dimmer. To control your lights from an app or remote, you'll need to replace an existing switch with a Caséta™ Wireless in-wall dimmer. Before installation, please watch the installation video at www.casetawireless.com/support. Enjoy the convenience of Caséta™ Wireless!

Double Your Warranty: Love Caséta™ Wireless dimmers? Share your feedback and extend your warranty by 1 year at www.casetawireless.com/register.

Contents Supplied

• In-wall dimmer (PD-6WCL)
• Wire connectors (3)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Phillips-head screwdriver
• Pliers

Bulb Compatibility

Works with energy-efficient dimmable light bulbs:

• LED: up to 150 W
• CFL: up to 150 W
• Halogen: up to 600 W
• Incandescent: up to 600 W

Note: You can mix and match dimmable LED and CFLs, as well as halogen and incandescent light bulbs. Dimmable LED and CFL performance may vary; visit www.casetawireless.com/lowend for adjustment information. For a complete list of compatible bulbs, visit www.casetawireless.com/bulblist.

Installing Your Dimmer (Single Pole Installation)

This guide covers installation for lights with one wall switch (single pole). For lights with two or more switches (3-way), visit www.casetawireless.com/3way.

1. Step 1: Turn Power Off

   ⚠️ WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

2. Step 2: Remove Existing Switch

   Remove the wallplate from the switch. Remove the switch and pull it away from the wall. Disconnect all three wires* from the switch.

   *If your switch has more than 3 wires, see the "Installing Caséta Wireless in a 3-way switch application" video at www.casetawireless.com/3way.

3. Step 3: Remove Side Sections (If Necessary)

   Bend side sections back and forth to remove. Do not remove outside side sections on dimmers at the end of a gang. Dimmer at the middle has all side sections removed. Each dimmer has inside side sections removed.

   Important Note: Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for details.

   Side sections removed	LED & CFL (or*)	Incandescent & Halogen
   None	150 W	600 W
   1 side	150 W	500 W
   2 sides	150 W	400 W

   *For maximum wattage when mixing bulb types, see www.casetawireless.com/ganging.

4. Step 4: Connect the Dimmer

   1. Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector.
   2. Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
   3. Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.

5. Step 5: Mount the Dimmer

   Use the provided screws to mount the dimmer in the wallbox.

6. Step 6: Attach the Wallplate

   Attach the adapter to the dimmer using the screws provided and snap on the wallplate. (If installing next to other devices, ensure the wallplate has the correct number of openings.)

7. Step 7: Turn Power On

   Turn power back on at the circuit breaker.

Using Your Caséta™ Wireless Kit

The Caséta™ Wireless dimmer can be controlled via a smartphone or tablet when used with the Lutron Smart Bridge™ (sold separately). If using with another manufacturer's bridge, refer to their instructions.

With a Smartphone or Tablet (Bridge Required)

1. Step 1: Download the Lutron® app

   Search "Lutron Caseta" on the App Store or Google Play. Visit www.casetawireless.com/LutronApp.

2. Step 2: Launch the Lutron® app

   The app will guide you through device setup.

3. Step 3: Use the Lutron® app to complete all remaining steps

   Including adding devices (Pico® remotes, dimmers, shades), controlling lights, scheduling, and remote access.

Without a Smartphone or Tablet (Bridge Not Required)

Pairing the Dimmer and Pico® Remote Control

1. Press and hold the "OFF" button on the dimmer for 6 seconds until LEDs start blinking.
2. Press and hold the "OFF" button on the Pico® remote control for 6 seconds until lights flash 3 times.
3. Press and hold the "Favorite" button on the Pico® remote control for 6 seconds until LEDs blink twice on the dimmer. The new favorite level is saved. Repeat to pair other Pico® remotes.

Changing the Favorite Light Level on the Pico® Remote Control

You can use the round "Favorite" button on the Pico® remote to recall a preferred light level (default is 50%).

1. Set the desired light level on the dimmer.
2. Press and hold the "Favorite" button on the Pico® remote control for 6 seconds until LEDs blink twice on the dimmer. The new favorite level is now saved.

Using Your Controls

In-wall Dimmer Controls

• ON: Turns lights on.
• Brighter: Increases light level.
• Darker: Decreases light level.
• OFF: Turns lights off.
• FASSTM (Front Accessible Service Switch): Pull out to remove power at the light socket for bulb replacement.

Pico® Remote Control (Sold Separately)

• ON: Turns lights on.
• Favorite: Recalls favorite light level.
• Brighter: Increases light level.
• Darker: Decreases light level.
• OFF: Turns lights off.

Troubleshooting

For additional troubleshooting suggestions, visit www.casetawireless.com/support.

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).

Device Ratings

In-wall dimmer: PD-6WCL, 120 V~ 50/60 Hz

Warnings and Compliance

CAUTION: Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent lamps. Do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances to avoid overheating or damage.

Codes: Install in accordance with all national and local electrical codes.

Grounding: If no grounding means exist in the wallbox, the National Electrical Code (NEC) allows installation if a nonmetallic faceplate is used or the circuit is GFCI protected. Cap or remove the green wire if installing by these methods.

FCC/IC Information: This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Operation is subject to two conditions: (1) no harmful interference, and (2) acceptance of any interference. Modifications not expressly approved by Lutron Electronics Co., Inc. may void the user's authority to operate this equipment. This equipment has been tested and found to comply with Class B digital device limits. These limits provide reasonable protection against harmful interference in residential installations. If interference occurs, try reorienting the antenna, increasing separation, or connecting to a different circuit. Consult a dealer or technician for help.

Warranty: For warranty information, please visit www.casetawireless.com/warranty.

About Lutron

Lutron®, and Pico® are registered trademarks and FASS™, Caséta™, and Smart Bridge™ are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association. Google and the Google logo are registered trademarks of Google Inc.

© 2014 Lutron Electronics Co., Inc.

P/N 0301730 REV B