Artika Skyview Ultra Thin Gimbal LED Recessed Pot Light

Included Hardware

The following items are included with your fixture:

Tools Needed

For installation, you will need:

• Hand Saw (Scie à main / Sierra de mano)
• Hole Saw (4 3/8" - 110 mm) (Scie-cloche / Broca de corona)

Safety Precautions & Important Information

WARNING: Risk of electrical shock. ⚡ Turn off the main electrical supply from the fuse box/circuit breaker before installing the unit or doing any maintenance. Do not use outdoors if not specified for such use.

CAUTION: If using a dimmer, it must be LED compatible.

IMPORTANT: The installer and/or user must read, understand, and follow these instructions before installing the product. Failure to follow instructions may void the warranty and could lead to product malfunction. It is recommended that this product be installed by a certified electrician, as required by local codes in some regions.

Step-by-Step Installation

1A. Preinstall Cut Ceiling Hole

Cut a hole in the ceiling with either a hand saw or a hole saw. The diagram shows a hand saw and a hole saw, with a dashed circle indicating the area to be cut.

1B. Preinstall Break Knock-out

Using a tool (e.g., screwdriver), break out the pre-scored circular section (knock-out) from the power box where the cable will enter. The diagram shows a screwdriver being used to remove this section.

2A. Wires Connection (No Dimmer)

This section details wiring for installations without a 0-10V dimmer. Connect the wires using the provided wire connectors. Wire colors typically include Purple, Grey, and Black (Line/L), White (Neutral/N), and Ground (GND). CAUTION: Do not use the Purple and Grey wires unless a 0-10V dimmer is connected.

2B. Wires Connection (0-10V Dimmer)

This section details wiring for installations with a 0-10V dimmer. Connect the dimmer wires (Purple and Grey) to the corresponding wires in the power box, along with the Line (Black), Neutral (White), and Ground wires.

3. Fixture Connection

Connect the fixture's cable to the power box using the provided quick connectors. The diagram shows the power box and fixture connected by cables, with a close-up of the connector mating.

4. Selectable White Technology

This fixture allows you to select the color temperature. Adjust the switch or dial on the fixture to choose between 2700K, 3000K, 3500K, 4000K, or 5000K. The diagram shows a close-up of the fixture with color temperature options indicated.

5. Feed Power Box Through Hole

Carefully feed the power box up through the hole in the ceiling. A large grey arrow in the diagram indicates the upward direction.

6. Feed Fixture Through Hole

Compress the fixture's spring clips (Step 1) and feed the fixture up through the hole in the ceiling (Step 2). Large grey arrows indicate the upward movement.

7. Final Install

Push the fixture into place until it is securely seated. You may hear a 'CLICK' as the spring clips engage. An upward arrow indicates the final position of the fixture.

USA (FCC) Compliance

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device does not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If interference occurs, the user is encouraged to try to correct it by reorienting/relocating the antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer or experienced technician.

Warranty

Artika For Living Inc. offers a five-year (5) limited warranty on manufacturing defects for residential use only, from the date of purchase. This warranty is non-transferable and applies to the original owner in the USA, Canada, Mexico, UK, Iceland, France, and Spain. It does not apply to retailers or commercial applications.

The original sales receipt is required for all warranty claims. The remedy is product or part replacement at Artika's discretion, not exceeding the original purchase price.

This warranty is valid only for products installed according to the building code, effective laws, and the provided instruction manual. It does not cover products installed incorrectly, subjected to abnormal use, normal wear and tear, misuse, negligence, vandalism, improper maintenance, accidents, abuse, fire, flood, theft, acts of God, neglect, or alterations. Accessories like bulbs or batteries are excluded. Handling, labor, and transportation costs are not covered.

Artika For Living Inc. is not responsible for direct or consequential damages or injuries arising from improper use or installation.

For more information, please visit www.artika.com.

Contact Information

Artika For Living Inc.

800, Boulevard Hymus
Saint-Laurent (Québec) H4S 0B5
Canada

Phone: 1-866-661-9606
Email: support@artika.com
Website: www.artika.com

Customer Service: Monday to Friday, 9 am - 5 pm EST. Service is provided in English, French, and Spanish.