Bathroom Product Installation Guides and User Manuals

1500/1700 L Shaped Bath Installation Instructions

?? Made in UK

Quality Acrylic Baths

ℹ️ Please Note:

• Baths should be set at supplied panel height.
• The baseboard is encapsulated into the bath.
• Remove the two tubular cradles from the bath. (Retain the transit cradle fixing screws No'5 Qty 4)
• Align the cradle and hand screw directly into the base of the bath using the 32mm transit cradle fixing screws. (Important! YOU MUST CHECK THE SCREW LENGTH FIRST ⚠️)
• Half the panel clips supplied should be secured (if possible) to the floor.
• Before the final fixing of the bath, fit tap and waste fittings using a suitable sealing compound.
• When complete place the bath into position, re-check levels and make any final adjustments necessary.
• Finally secure the feet to the floor and the wall brackets to the wall. Movement may occur if not fitted correctly.
• CHECK THAT THE BATH RIM IS LEVEL. ⚠️

Before you start

• Before fixing remove ALL protective covering and examine carefully. The polythene film must be removed in full and the bath checked for any visible damage.
• Unpack and check the product is complete and undamaged.
• Have the correct tools available.
• Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from damaged or faulty product being installed. The guarantee does not cover impact related damage.
• Please dispose of all packaging with due regard to the environment.

⚠️ Safety

• Handle the bath with care.
• This product is heavy and requires two persons to carry.
• When drilling walls, check first for hidden pipes and cables. ⚠️
• Use safety eyewear when drilling. ⚠️
• Keep small parts away from children. ⚠️

?️ Tools required

• Spirit Level
• Pozi Screwdriver
• Tape Measure
• Spanners (13mm & 17mm)
• Pencil
• Junior Hacksaw
• Drill
• Appropriate Drill Bit

*Tools shown not supplied. *Ensure drill bit used is suitable for wall surface!

? Parts provided

• Pair of Tubular Cradles x1
• Cradlle Toggles x4
• M10 x 152mm Foot x4
• Wall Fixing Brackets x2
• 32mm Transit Cradle Fixing Screws x4
• 16mm Self Tapping Screws x36
• M8 x 117mm Centre Foot x1
• Centre Foot Bracket x1
• M10 Nuts x8
• M8 Nuts x2
• Panel Clips x10

We have taken great care to ensure that this product reaches you in perfect condition. However should any parts be damaged or missing please contact your point of purchase. This does not affect your statutory rights. In addition if you require replacement parts your point of purchase will be happy to assist.

Please discard any additional spare parts with due regard to the environment.

25 Year Guarantee ?️

Please note, bath shown is for illustrational purposes.

Diagram Description: Bath Assembly

Shows an exploded view of the 1500/1700 L Shaped Bath assembly, illustrating various parts such as screws, cradles, feet, and brackets, with numerical labels indicating their placement during installation.

Diagram Description: Bath

Illustration of the 1500/1700 L Shaped Bath, presented for illustrative purposes.

Maia L Shape 6mm Chrome Bath Screen Installation Instructions

BeBa_28043

? Multi-person assembly

?️ Tools required

? We always recommend using professional tradespeople to install your product

ℹ️ Important information

• Please read these instructions thoroughly and retain for future reference
• Manufactured to BS EN 14428
• Please check for pipes and cables before drilling ⚠️
• Please check for damage prior to installation ⚠️

Parts / Diagrams

Diagram Description: Bath Screen Components

Shows numbered components of the Maia L Shape Bath Screen, including profiles (03), screws (02, 06), and sealing strips (07), along with fixing plugs/dowels (01) and washers/spacers (05).

Tools required

Diagram Description: Tools for Bath Screen

Illustrates the tools required for installing the bath screen: Spirit Level, Pozi Screwdriver, Tape Measure, Spanners, Pencil, Junior Hacksaw, Drill with drill bits (Ø6, Ø3.2), and Sealant Gun & Sealant.

⚙️ Installation

Diagram Description: Bath Screen Installation Steps

Step-by-step diagrams illustrating the installation process for the Maia L Shape Bath Screen. Step 1 shows attaching a wall profile. Step 2 shows attaching a profile to the bath edge. Step 3 shows mounting the screen onto the profiles. Step 4 shows securing the screen. Step 5 depicts a final check or seal, possibly indicating a 24-hour waiting period.

? Cleaning

All parts of the product shall be cleaned with a cloth soaked in neutral detergent soapy water. Please do not use sharp tools such as blades to clean the shower door. ⚠️ Please do not use strong detergent, alcohol or any abrasive cleaning substances to clean the shower door. If the stain is serious, a low concentration of vinegar can be used, but must be rinsed with clean water afterwards.

Portland Range Bathroom Furniture Fitting Guide

Note: For safety reasons Unit must be secured to the wall using suitable fixings (pre-drilled holes provide in back panel of unit) ⚠️. When fitting a basin to a unit, a bead of silicone should be applied to the top edge of the basin unit to seal between the basin and unit. ℹ️

?️ Tools required for installations

Diagram Description: Furniture Tools

Illustrations of tools required for bathroom furniture installation, including a spirit level, hammer, pencil, screwdrivers, drill, and drill bits.

Hinge Adjustment

Diagram Description: Hinge Adjustment Steps

Illustrations demonstrating Hinge Adjustment steps: A - Vertical (Loosen screw 'A' on all hinges, adjust door, retighten screw), B - Lateral (Loosen screw 'B', adjust door, retighten screw), C - Horizontal (Loosen screw 'B' ½ turn, turn screw 'C' until door is positioned correctly, retighten screw 'B').

Drawers Remove/Install

Diagram Description: Drawer Mechanism

Diagrams illustrating the process for removing, installing, and adjusting the position of drawers. Step 'A' shows removing the fastener, Step 'B' shows installing/locking the fastener, and Step 'C' shows adjusting the screw for drawer position.

Wall hung unit installation

Please measure the L distance between each bracket on the unit and H (height as customers request). The standard height is 850mm (including basin height) from floor to wash basin.

Diagram Description: Wall Hung Unit Fixing

Shows 6 steps for installing wall-hung bathroom units, including measuring distances (L and H) and fixing to the wall. Indicates '1 helper for some tasks' for certain steps.

Mirror cabinet and Storage unit installation

Please measure the L&H distance between each pre-drilled holes on products and fix them as below steps. The distance will be 300-400mm for the mirror cabinet to the basin. The distance from floor to bottom of storage is as customer requests.

Diagram Description: Cabinet/Storage Unit Fixing

Illustrates 6 steps for installing mirror cabinets and storage units, including measuring distances (L and H) and fixing points. Indicates '1 helper for some tasks' for certain steps.

Top Fix Soft Close Toilet Seat Installation Instructions

? Single-person assembly

?️ Tools required

? We always recommend using professional tradespeople to install your product

ℹ️ Important information

• Please read these instructions thoroughly and retain for future reference
• Manufactured to BS EN 1254 – Specification for WC seats (plastics)

Parts

• 1. Expanding Plug
• 2. Gasket
• 3. Fitting Peg
• 4. Fixing Screw
• 5. Fitting Cover
• 6. Seat/Lid Assembly

Tools required

Screwdriver

⚙️ Installation

Diagram Description: Toilet Seat Installation Steps

Step-by-step diagrams illustrating the installation of the Top Fix Soft Close Toilet Seat. Step 1 shows pushing expanding plugs into the toilet pan, placing gaskets, and inserting screws loosely. Step 2 shows aligning the seat onto the pegs and clicking it into place. Step 3 shows tightening the screws and removing the seat by pressing buttons. Step 4 shows placing the fitting covers over the fixed fittings.

Using

During use do not force the seat closed as this will damage the soft close mechanism. ⚠️ Pull the seat and/or lid towards you slightly until it reaches the point at which it will fall under its own weight, then release. Do not stand on the toilet seat. ⚠️

? Cleaning

To maintain the surface of your product, wipe with a clean damp cloth and wipe dry, do not use any abrasive cleaning agents or materials. It is recommended to wipe the seat and fittings on a regular basis.

❓ Troubleshooting

• Seat becomes loose after a period of use: Remove the seat and re-tighten the fittings.
• Soft close mechanism stops working: The mechanism cannot be replaced; replace the seat and lid. However, the fittings can remain fitted. Removal of seat/lid is advised in Maintenance (below).
• Seat is short or overhangs the toilet pan: Align the seat lid with the front edge of the toilet pan; the fittings are adjustable.

? Maintenance

• To remove the seat/lid, press the two buttons at the rear of the seat and pull the seat/lid away from the fitting pegs. When replacing ensure it clicks into place.
• To access the fixing screws, remove the lid/seat as above, then pull off the covers.

Dual Flush Valve Instruction

Functional Instruction

• The flush valve has 2 flushing ways: half-flush and full flush. When you push the full flush, the discharge volume is big, and when you push the half flush, the discharge volume is small.
• Water level of half flush is adjustable.
• Water level of full flush is adjustable.

Installation Steps

Preparation before Installation

Remove the old fittings and wash the tank before installation. Wash clean because many impurities probably existed in the conduit.

Fill Valve Installation

Diagram Description: Fill Valve Installation

Details steps for installing the fill valve (3-1, 3-2, 3-3). Shows inserting the fill valve into the water tank, connecting the water supply pipe, and adjusting the water level using a rod, buoy, and adjustment nut.

Flush Valve Installation

Diagram Description: Flush Valve Installation (One-piece & Two-piece)

Illustrates installation for both one-piece (1-1 to 1-5) and two-piece (2-1 to 2-3) flush valves. Shows components like the pedestal, drainage body, stainless steel hook, sealing washer, bolt, and drainage nut, and the steps to assemble and secure them.

Water Tank Installation

Shows how to place the water tank on the ceramic toilet, locate the standard washer at the outlet, insert the jointed bolt, and screw the jointed nut closely.

Examination (Fill Valve)

Instructions to check the fill valve's operation after installation, ensuring the buoy is active, the water-stop cup opens and closes normally without leakage, and the water level is correct.

Push button Installation

Diagram Description: Push Button Installation

Shows steps (6-1 to 6-5) for installing the push button assembly. Includes diagrams of the push button, body, nut, and adjustment mechanism, and how to connect the flush rod to the correct key-press.

Examination Again

Instructions to confirm installation completion by checking the water-stop washer and the functionality of both full flush and half flush operations.

❓ Troubleshooting

Installation Instructions For Floor Fixing Kit (WC pan)

1. The WC pan should be installed on a flat surface and placed in its final intended position.

2. Using the diagram below as a guide, position each plastic floor fixing bracket inside the walls of the WC pan directly behind the fixing holes.

3. Mark off and using the plugs, washer and fixing screws provided, drill and secure the plastic bracket to the floor. You will need to move the pan away from the brackets to make space for fixing.

3. With the fixing brackets firmly in position, replace the WC pan back in position. Check that the fixing brackets line up with the holes in the WC pan.

4. From the outside wall of the WC pan, place the plastic cover gasket over the side fixing screw and thread into the floor fixing bracket. Take care not to over-tighten. ⚠️

4. Place the cover caps over the head of the side fixing screws. If required use a small amount of silicone sealant to assist with attaching the cover caps permanently. ℹ️

5. Check WC is firmly fixed.

? Diagram Key

• 1. Flat surface
• 2. Plugs
• 3. Plastic floor fixing bracket
• 4. Washer
• 5. Floor fixing screw
• 6. Plastic cover gasket
• 7. Side fixing screw
• 8. Cover cap
• 9. WC pan

Diagram Description: WC Pan Floor Fixing

Shows a cross-section of a WC pan being fixed to the floor using brackets, screws, and plugs. It details the components involved in securing the pan to a flat surface.