Hooke Road BXG.8822 Front Bumper Installation Instructions
Model: BXG.8822
Attention: Please verify all parts are present and read instructions carefully before starting installation. Please feel free to contact your distributor if you have any kind of question about your purchase.
Contents
Parts List
| Qty | Part Name | Size(mm) | Description |
|---|---|---|---|
| 1 | Bull Bar | - | Part A |
| 2 | Wings | - | Parts B1 & B2 |
| 1 | Main Body | - | Part C |
| 2 | License Plate Bracket | - | Parts D1 & D2 |
| 1 | Skid Plate | - | Part E |
| 2 | Skid Plate Mounting Brackets | - | Parts F1 & F2 |
| 4 | Hex Bolt | M12*35 | - |
| 6 | Hex Bolt | M12*30 | - |
| 7 | Hex Bolt | M8*20 | - |
| 4 | Button Bolt | M6*16 | - |
| 10 | Split Lock Washer | D12 | - |
| 7 | Split Lock Washer | D8 | - |
| 14 | Flat Washer | M12*30*1.5 | - |
| 7 | Flat Washer | M8 | - |
| 4 | Flat Washer | M6*12*1 | - |
| 2 | Nylon Round Spacer | M6*12*1.3 | - |
| 4 | Nylon Lock Nut | M6 | - |
| 10 | Hex Nut | M12 | - |
| 4 | Flange Hex Lock Nut | M8 | - |
| 2 | EVA | - | - |
Tools Required
- Drive Ratchet Handle
- 10mm, 13mm, 19mm Wrench
- 4mm Hex Bit Socket
Installation Instructions
Step 1: Prepare the Vehicle
Place the vehicle in park, remove the factory bumper from the frame. Keep the (2) lower bolts for installation.
Diagram Description: Shows the front of a vehicle with the factory bumper removed, highlighting the frame rails and mounting points. Two lower bolts are indicated to be retained.
Step 2: Attach EVA and Main Body
First, stick the EVA pad to the main body. Assemble the Hooke Road bumper by aligning the outer profile with the inner profile and tightening all hardware. Repeat this step on the other side of the bumper.
Parts Used:
- (6) M12×30 Hex Bolts
- (6) D12 Split Lock Washers
- (2) EVA
- (6) M12×30×1.5 Flat Washers
- (6) M12 Hex Nuts
Diagram Description: Illustrates attaching an EVA pad to the main bumper body (Part C). Then shows the main body being aligned and bolted to the vehicle frame, using M12 bolts, washers, and nuts. The process is shown for both sides.
Step 3: Secure the Bull Bar
Secure the bull bar (Part A) onto the bumper, then tighten all hardware.
Parts Used:
- (2) M8×20 Hex Bolts
- (2) D8 Split Lock Washers
- (2) M8 Flat Washers
- (2) M8 Flange Hex Lock Nuts
Diagram Description: Shows the bull bar (Part A) being attached to the front of the main bumper assembly using M8 bolts, washers, and nuts.
Step 4: Assemble License Plate Brackets
Assemble the license plate brackets (Parts D1 & D2), then secure them onto the bumper and tighten all hardware.
Parts Used:
- (4) M6×16 Button Bolts
- (4) M6×12×1 Flat Washers
- (2) M6×12×1.3 Nylon Round Spacers
- (4) M6 Nylon Lock Nuts
Diagram Description: Depicts the assembly of the license plate brackets (D1, D2) using M6 bolts, washers, spacers, and nuts. The assembled brackets are then shown being attached to the bumper.
Step 5: Mount the Bumper to Frame Rails
Place the bumper assembly onto the frame rails, then secure it to the vehicle frame. Adjust it to the desired position, then tighten all bolts.
Parts Used:
- (4) M12×35 Hex Bolts
- (4) D12 Split Lock Washers
- (8) M12×30×1.5 Flat Washers
- (4) M12 Hex Nuts
Diagram Description: Shows the complete bumper assembly being positioned onto the vehicle's frame rails. It illustrates the use of M12 bolts, washers, and nuts to secure the bumper to the frame.
Step 6: Attach Mounting Brackets and Skid Plate
Secure the mounting brackets (Parts F1 & F2) to the vehicle and the skid plate (Part E) to the bumper. Connect the skid plate to the brackets, then tighten all hardware.
Parts Used:
- (5) M8×20 Hex Bolts
- (2) Factory Bolts
- (5) D8 Split Lock Washers
- (5) M8 Flat Washers
- (2) M8 Flange Hex Lock Nuts
Diagram Description: Illustrates attaching the mounting brackets (F1, F2) to the vehicle frame. Then shows the skid plate (E) being attached to these brackets using M8 bolts, washers, and nuts. It also indicates the use of factory bolts.
Step 7: Installation Complete
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
Diagram Description: A final image of the installed Hooke Road front bumper on a vehicle, showcasing the completed look.
