Progress Lighting
Installation Guide for P500390 (3-LT FOYER) and P500391 (4-LT FOYER)
Package Contents
This section details the components included in the package for both the P500390 (3-LT FOYER) and P500391 (4-LT FOYER) models. The package contains:
- Part A: Fixture (Quantity: 1)
- Part B: Chain Loop (Quantity: 1)
- Part C: Cover (Quantity: 1)
Visual representations of the P500390 and P500391 fixtures are provided.
Hardware Contents (Not Actual Size)
The following hardware pieces are included:
- AA Hex Nut: Quantity: 2
- BB Wire Nut: Quantity: 3
- CC Mounting Strap: Quantity: 1
- DD Screw Collar: Quantity: 1
- EE Chain Holder: Quantity: 1
- FF Nipple: Quantity: 1
- GG Chain: Quantity: 1
- HH Canopy: Quantity: 1
- JJ Quick link: Quantity: 1
Safety Information
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
CAUTION: Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Use minimum 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
Step 1: Mount the Fixture Support
Install the chain holder (EE) onto the nipple (FF). Next, loosely thread the hex nuts (AA) onto the nipple (FF) and then thread this assembly onto the mounting strap (CC). Install this assembly to the outlet box using the mounting screws supplied with the outlet box (not included). The diagram shows the mounting strap (CC) attached to the ceiling electrical box, with the nipple (FF) threaded through it and secured by hex nuts (AA). The chain holder (EE) is threaded onto the nipple.
Step 2: Adjust Canopy Depth
Adjust the depth of the chain holder in relation to the canopy depth. Take the canopy (HH) and slip it over the chain holder (EE). Adjust the chain holder so at least 1/4" [6mm] of the threaded portion of the nipple (FF) is exposed through the canopy hole. Tighten the top hex nut (AA) against the mounting strap (CC) and the bottom hex nut (AA) against the chain holder (EE) to secure the position. The diagram illustrates this adjustment process.
Step 3: Assemble Fixture Body
Pass the fixture wires (J) from the socket cluster (H) up through the stem (G) and swivel (F), and assemble the stem/swivel to the socket cluster (H). Tighten securely. Next, pass the wires (J) up through the fixture top plate (E) and secure the stem/swivel to the fixture (A) with the hex coupling (D). Tighten securely. Finally, pass the wires (J) up through the cover (C) and the chain loop (B). Attach the cover (C) onto the fixture (A) using the chain loop (B) to secure it tightly. The diagram shows the wires being routed through these components.
Step 4: Determine Hanging Length and Attach Chain
Determine the hanging length of your fixture by removing chain links (GG) and optionally cutting the electrical and ground wire to length. Do NOT cut electrical or ground wires until this overall length is determined. Leave at least 6 inches minimum of wire past the chain holder (EE) for easy connections. Chain links can be spread open with two pairs of pliers by twisting the split link ends in opposite directions and closing them by squeezing them back together.
Once hanging length is determined, open a chain link (GG) at one end and hook it onto the chain loop (B). Close the chain links back together with pliers. Open the quick link (JJ) by loosening the hex (JJ). Attach the other end of the chain (GG) along with the chain holder (EE) onto the quick link (JJ). Close the quick link by tightening the hex back up. Weave the wires through every third chain link (GG). Continue to pass the wires and chain through the screw collar (DD) and canopy (HH). The diagram illustrates these steps.
Step 5: Make Electrical Connections
Strip 3/8" of insulation from the electrical wire ends. Using wire nuts (BB), connect the ribbed fixture wire to the WHITE supply wire from the outlet box. Connect the smooth fixture wire to the BLACK supply wire. Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the mounting strap. Push all wire connections into the outlet box. The diagram shows the wire connections and the use of wire nuts.
Step 6: Secure Canopy
Tuck the wires into the junction box and slip the canopy (HH) over the chain holder. Thread the screw collar (DD) onto the chain holder to secure the canopy tightly to the ceiling. The diagram illustrates this final securing step.
Step 7: Install Lamps
Thread the lamps (not included) into the fixture sockets. Use 60-watt maximum incandescent candelabra base, SBCFL, or SBLED lamps.
Warranty Information
WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers' sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress's sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer's sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer's responsibility. Customer is responsible for determining the suitability of our products for customer's use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.
Contact Information
For questions regarding product information, assembly, or missing parts, please contact Progress Lighting:
Phone: 800-447-0573 (8am-8pm Eastern, Monday-Friday)
Email: customerservice@progresslighting.com
