Progress Lighting P350270 Pinellas 4-Light Semi-Flush Mount Ceiling Light Installation Guide

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

CAUTION: Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.

WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

French Safety: Mise en garde: Lire les instructions avec soin et couper le courant au disjoncteur central avant de commencer l'installation. Mise en garde: Risque d'incendie. Min 90°C conducteurs d'alimentation. Consulter un électricien qualifié pour assurer le bon conducteur de circuit de dérivation. Avertissement - S'il y a d'autres mécanismes régulateurs qui s'emploient avec ce dispositif, suivre soigneusement les instructions pour satisfaire aux exigences NEC. Si vous avez des questions, consulter un électricien qualifié. Mise en garde - Le verre est toujours fragile; maniez le(s) composant(s) et/ou l' (les) ampoule(s) avec prudence.

Spanish Safety: Precaución: Lea cuidadosamente las instrucciones y desconecte la electricidad del cortacircuitos principal antes de iniciar la instalación. Precaución: Riesgo de fuego. Min. 90°C los cables de suministro. Consulte a un electricista calificado para asegurarse de que el conductor del circuito derivado correcto. Advertencia - Si usa algún dispositivo especial de control con este aparato de luz, siga las instrucciones cuidadosamente para asegurar la completa conformidad con los requisitos N.E.C. Si existe alguna duda, contacte un electricista calificado. Precaución - El vidrio es frágil; tenga cuidado al manipular el (los) elemento(s) de vidrio y/o la(s) bombilla(s).

Preparation

1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Package Contents

Diagram Description (Ceiling Mounting): Shows fixture part A attached to a ceiling mount. Part C (steel shade) is suspended below. Part G (canopy) is above. Part D (stem) connects A to the mounting. Part E (steel bracket) supports the shade. Part F (finial) is at the bottom.

Diagram Description (Hanging Mounting): Shows fixture part A suspended from a ceiling. Part G (canopy) and H (90° swivel) are at the top. Part D (stem) connects A to the hanging hardware. Part B (steel shade) is shown below A.

Hardware Contents (not actual size)

Assembly Instructions

Step 1: Prepare Mounting Plate

Loosely thread screws (AA) and hex nuts (DD) onto the round mounting plate (CC) as shown. Adjust screw length according to the fixture canopy depth.

Attach this assembly to the outlet box using mounting screws (not provided). Tighten securely.

Lift the fixture and pass screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture, thread screws (AA) in or out of the round mounting plate (CC) until 3/16" [5mm] of threads are showing. This length is for mounting the fixture.

Diagram Description: Shows screws (AA) and nuts (DD) on mounting plate (CC). Another diagram shows the assembly attached to an outlet box. A third diagram illustrates adjusting screw (AA) length, showing an "INCORRECT" state with too much thread exposed and a "CORRECT" state with 3/16" [5mm] thread showing. Text indicates "Thread both screws up & down for adjustment".

Step 2: Attach Fixture Canopy

Slip fixture (A) wires through canopy (G). Thread canopy (G) down onto fixture (A).

Diagram Description: Shows fixture (A) wires passing through canopy (G), which is then threaded down onto the fixture.

Step 3: Install Lamps

Thread the lamps (not included) into the fixture sockets. Use 40-watt MAX incandescent medium base lamp, SBCFL or SBLED.

Diagram Description: Shows lamps being screwed into the fixture sockets.

Step 4: Electrical Connections

Strip 3/8" of insulation from electrical wire ends.

Using wire nuts (BB):

• Connect RIBBED fixture wire to the WHITE supply wire from the outlet box.
• Connect the SMOOTH fixture wire to the BLACK supply wire.
• Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate.

Push all wire connections into the outlet box.

Diagram Description: Shows wire connections: ribbed fixture wire to white supply, smooth fixture wire to black supply, and ground wires connected. It illustrates wire nuts (BB) and the ground screw.

Step 5: Secure Canopy

Secure the canopy (G) to screws (AA) using the two cylinder nuts (EE) to secure tightly.

Diagram Description: Shows canopy (G) being secured to screws (AA) with cylinder nuts (EE).

Step 6: Attach Shades and Finial (Ceiling Mount)

Line up the hole in the steel shade (B) and steel bracket (E) with the studs and secure in place with cylinder nuts (EE).

Attach the steel shade (C) to the steel bracket (E) nipple, and using the finial (F) secure it tightly to the fixture.

Diagram Description: Shows steel shade (B) and bracket (E) being attached to studs with nuts (EE). Then, steel shade (C) is attached to bracket (E) with finial (F).

Step 7: Prepare for Hanging Mount

Remove existing canopy parts and canopy (G) from fixture (A).

Install canopy (G) parts and 90° swivel (H) into canopy (G), secure tightly.

Diagram Description: Shows canopy parts being removed from fixture (A), then canopy (G) and swivel (H) being installed into canopy (G).

Step 8: Determine Hanging Length and Wire Through Stems

NOTE: Determine the hanging length of your fixture by adding or removing stems (pipes FF, GG, HH). The electrical and ground wire may also optionally be cut to length.

Do NOT cut electrical or ground wires until this length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy (G) 90° swivel (H) to allow for easy connections.

Once hanging length is determined, pass wires through pipe (FF), nipple (HH), and pipe (GG), tightening the stem assembly to fixture (A) as you go to avoid twisting the wires. Pass wires through canopy (G). Tighten the 90° swivel of canopy (G) to the stem assembly.

Diagram Description: Shows wires being passed through pipes (FF, HH, GG) and the stem assembly. It also shows wires passing through canopy (G) and the swivel (H) being tightened.

Step 9: Electrical Connections (Hanging Mount)

Strip 3/8" of insulation from electrical wire ends.

Using wire nuts (BB):

• Connect RIBBED fixture wire to the WHITE supply wire from the outlet box.
• Connect the SMOOTH fixture wire to the BLACK supply wire.
• Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate.

Push all wire connections into the outlet box.

Diagram Description: Similar to Step 4, showing wire connections using wire nuts (BB) and the ground screw.

Step 10: Secure Canopy

Secure the canopy (G) to screws (AA) using the two cylinder nuts (EE) to secure tightly.

Diagram Description: Shows canopy (G) being secured to screws (AA) with cylinder nuts (EE).

Warranty Information

Progress warrants products against defects in material and workmanship for one year from purchase. Claims require proof of purchase. The sole remedy is repair or replacement. Progress is not liable for incidental or consequential damages. Customers are responsible for product suitability.