Philips TAH8000 Headphones User Manual

Introduction

Welcome to Philips! Register your product at www.philips.com/support to fully benefit from Philips support.

With these Philips headphones, you can:

• Enjoy convenient wireless handsfree calls
• Enjoy and control music wirelessly
• Switch between calls and music
• Enjoy noise cancellation

What's in the Box

The package includes:

• Philips TAH8000 Over-ear ANC headphones
• USB charging cable (for charging only)
• Audio cable (3.5mm, 1.0m)
• Quick start guide
• Global Warranty leaflet
• Safety leaflet

Overview of Your Over-ear Headphones

The headphones feature the following controls and indicators:

• 1. ANC/Awareness mode button: Controls Active Noise Cancellation and Awareness modes.
• 2. Multi-Function Button (MFB): Used for play/pause, call control, and voice assistant activation.
• 3. Power button: Turns the headphones on or off.
• 4. LED indicator: Shows charging status, pairing mode, and connection status.
• 5. USB-C charging slot: For charging the headphones.
• 6. 3.5mm Audio jack: For wired connection.
• 7. Mic: Microphone for calls.

Get Started

Charge the Battery

Before first use, charge the battery for 2 hours for optimal capacity and lifetime. Use only the original USB-C cable. Charging takes approximately two hours. The LED indicator turns white while charging and turns off when fully charged.

If the headset is not used for a long time, charge the battery at least once every three months.

App Download

Download the "Philips Headphones" app from the Apple App Store or Google Play to customize your sound and calling experience.

Pairing Your Headphones

Pair for the First Time

1. Ensure headphones are fully charged and powered off.
2. Press and hold the Power button for 2 seconds to enter pairing mode. The LEDs will flash white and blue alternately.
3. Turn on the Bluetooth function on your device.
4. Select "Philips TAH8000" from your device's Bluetooth list.
5. If prompted, enter the password "0000" (for devices below Bluetooth 3.0).

Pair with Another Bluetooth Device

To pair with a second device, turn on the headphones and press the MFB for 5 seconds to enter pairing mode again.

Note: The headphones can store up to 5 paired devices. Older devices are replaced when a new one is added.

Multi-point Connection

Pair the headphones with two devices simultaneously (e.g., a mobile phone and a notebook). You can listen to music from one device and receive calls from the other. Pause audio from one device to play audio from the other.

Note: When streaming from Device 1, a call from Device 2 will pause Device 1 playback and route the call to the headphones. Ending the call resumes playback from Device 1.

Connect via 3.5mm Audio Cable

When the battery is depleted or Bluetooth is unavailable, connect the headphones using the included 3.5mm audio cable.

Use Your Headphones

Connecting to Bluetooth

Turn on your Bluetooth device and then press and hold the Power button on the headphones for 2 seconds. The white LED will illuminate, and the headphones will automatically reconnect to the last connected device.

Tip: If Bluetooth is turned on after the headphones, manual connection via the device's Bluetooth menu may be required.

Power On/Off

• To turn on: Press and hold the Power button for 2 seconds.
• To turn off: Press and hold the Power button for 2 seconds. The white LED will be on for 3 seconds.

Control ANC (Active Noise Cancellation)

Toggle ANC modes by pressing the ANC/Awareness mode button on the right earcup:

• ANC is automatically activated when headphones are worn.
• Press once to turn ANC off.
• Press again to switch to Awareness mode.

ANC Modes:

• ANC ON: Press button once.
• ANC OFF: Press button once.
• Awareness mode: Press button once.
• Quick Awareness: Press and hold for one second.

Note: ANC works wirelessly via Bluetooth and wired via the 3.5mm jack.

Manage Your Calls and Music

Music Control:

• Play/Pause: Single press MFB.
• Previous Track: Push MFB towards "-" and hold for one second.
• Next Track: Push MFB towards "+" and hold for one second.
• Volume Up: Push MFB towards "+".
• Volume Down: Push MFB towards "-".

Note: A tone indicates when the maximum volume level is reached.

Call Control:

• Pick up call: Single press MFB.
• Hang up/Reject call: Press and hold MFB for 1 second.

Three-Way Calling:

• Hold current call and accept incoming call: Single press MFB.
• Hold current call and reject incoming call: Press and hold MFB for 1 second.
• Switch between second-way call and three-way call: Single press MFB.

Voice Assistant

• Trigger Voice Assistant (Siri/Google): Press MFB twice.
• Stop Voice Assistant: Press MFB once.

Headphones LED Indicator Status

Reset the Headphones

If you experience pairing or connection issues, follow these steps to reset the headphones to factory default settings:

1. On your Bluetooth device, go to the Bluetooth menu and remove "Philips TAH8000".
2. Turn off the Bluetooth function on your device.
3. Turn on your headphones.
4. Press and hold the Power button and the ANC button simultaneously for 4 seconds.
5. Follow the steps in "Use your headphones - Connect the headphones to your Bluetooth device."
6. Pair the headphones with your Bluetooth device by selecting "Philips TAH8000".

Technical Data

• Music Play Time: 70 hours (ANC off), 50 hours (ANC on)
• Charging Time: 2 hours
• Battery: Rechargeable lithium-ion, 1000 mAh
• Bluetooth Version: 5.4
• Bluetooth Profiles: HFP, A2DP, AVRCP
• Supported Audio Codecs: SBC, AAC, LDAC, LC3
• Frequency Range: 2.4-2.4835 GHz
• Transmitter Power: < 10 dBm
• Operating Range: Up to 10 meters (33 feet)
• Features: Auto power off, USB-C port for charging, Multi-point connection

Note: Specifications are subject to change without notice. Battery life is approximate and may vary.

Notice

Declaration of Conformity

TP Vision Europe B.V. declares that this product complies with essential requirements and relevant provisions of RED Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. The Declaration of Conformity can be found at www.philips.com/support.

Disposal of Your Old Product and Battery

This product is designed with high-quality, recyclable materials. The symbol on the product indicates it is covered by European Directive 2012/19/EU (WEEE). The symbol on the battery indicates it is covered by European Regulation (EU) 2023/1542 and cannot be disposed of with household waste. Inform yourself about local collection systems for electrical products and batteries. Dispose of old products and batteries responsibly to prevent negative environmental and health consequences.

Remove the Integrated Battery

If no recycling system is available in your country, remove the battery before disposing of the headphones to protect the environment. Ensure the headphone is disconnected before battery removal.

Compliance with EMF

This product complies with applicable standards and regulations regarding exposure to electromagnetic fields.

Environmental Information

Packaging materials are minimized and can be recycled. Observe local regulations for disposal of packaging, batteries, and equipment.

Notice of Compliance

FCC Rules

This device complies with FCC Rules Part 15. Operation is subject to two conditions: (1) it must not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with Class B digital device limits per FCC Rules, designed for reasonable protection against harmful residential interference. It generates, uses, and can radiate radio frequency energy. Improper installation or use may cause radio communication interference. If interference occurs, try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing separation between equipment and receiver.
• Connecting equipment to a different circuit than the receiver.
• Consulting a dealer or experienced radio/TV technician.

FCC Radiation Exposure Statement

This equipment complies with Canada radiation exposure limits for uncontrolled environments. The transmitter must not be co-located or operated with any other antenna or transmitter. Install and operate with a minimum distance of 0mm between the radiator and your body.

The US (FCC) SAR limit is 1.6 W/kg averaged over one gram of tissue. This device has been tested for FCC SAR compliance. The highest reported SAR level for head usage (0mm) is 0.058 W/kg.

Caution: Modifications not expressly approved by the party responsible for compliance may void the user's authority to operate the equipment.

Canada

This device complies with Industry Canada's license-exempt RSS(s). Operation is subject to two conditions: (1) the device must not cause interference, and (2) the user must accept any interference, including interference that may compromise its operation. CAN ICES-(B)/NMB-(B).

IC Radiation Exposure Statement

This equipment complies with Canada's radiation exposure limits for uncontrolled environments. The transmitter must not be co-located or operated with any other antenna or transmitter. Install and operate with a minimum distance of 0mm between the radiator and your body.

Trademarks

Bluetooth: The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. MMD Hong Kong Holding Limited uses these marks under license. Other trademarks and trade names belong to their respective owners.

Siri: Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

Google: Google and Google Play are trademarks of Google LLC.

Frequently Asked Questions

My Bluetooth headphones do not turn on.

The battery level is low. Charge the headphones.

I cannot pair my Bluetooth headphones with my Bluetooth device.

Ensure Bluetooth is enabled on your device and the headphones are in pairing mode. Refer to the "Pairing Your Headphones" section.

How to reset pairing.

While powered on, press and hold the MFB for 5 seconds until the blue and white LED flashes alternately. This triggers re-pairing mode for switching devices or connecting to a new source device.

I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward).

Ensure your Bluetooth audio source supports AVRCP. Refer to 'Technical data' on page 11.

The volume level of the headphones is too low.

Some Bluetooth devices may not sync volume levels. Adjust the volume directly on your Bluetooth device.

The Bluetooth device cannot find the headphones.

The headphones may be connected to a previously paired device. Turn off the other device or move it out of range. Resetting the headphones might also be necessary. Refer to 'Pair the headphones with another Bluetooth device' on page 7.

My Bluetooth headphones are connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker.

Refer to your mobile phone's user manual to select audio output through the headphones.

The audio quality is poor and crackling noise can be heard.

The Bluetooth device may be out of range. Reduce the distance or remove obstacles. Charge your headphones.

Clean your headphones regularly.

Use a clean, damp cloth to clean the sound conduits and microphone holes, avoiding buildup of sweat or earwax. If water enters the sound conduits, the sound may drop or cut out temporarily. Dry thoroughly with a soft, damp cloth. Ensure headphones are completely dry before charging or use. Avoid alcohol-based cleaning agents.

Charge your headphones regularly.

If not used for a long time, charge the battery at least once every three months.