VEVOR Tool Cart

Product Overview

This document provides original instructions for the VEVOR Tool Cart, Model T271802. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The product appearance is subject to the item received. Updates to technology or software may occur without prior notification.

Important Safety Instructions

⚠️ Warning: To reduce the risk of injury, user must read instructions manual carefully.

[Precaution Symbol] This symbol, placed before a safety comment, indicates a kind of precaution, warning, or danger. Ignoring this warning may lead to an accident. To reduce the risk of injury, fire, or electrocution, please always follow the recommendations shown below.

? Warning: Be sure to wear gloves when using this product.

General Warnings:

1. Keep this manual for safety warnings and precautions. It offers important information on how to assemble, use, and maintain this product.
2. Please handle metal edges carefully.
3. DO NOT stand on this product or use it as a ladder.
4. DO NOT alter this product in any manner that is not intended, as this may cause product damage or personal injury.
5. Always assemble on an even surface.
6. The maximum loaded weight on the tool cart is no more than 400 lbs, evenly distributed.
7. Bind the goods with the cart tightly with the Tie-down strap before moving.

Assembly Precautions:

1. Please assemble the product in strict accordance with the instructions. Incorrect assembly could be hazardous.
2. Please wear safety goggles and work gloves properly during assembly.
3. Do not try to assemble the product when feeling tired or when under the influence of alcohol, drugs, or medication.
4. Load-bearing capacity and other product parameters are applied to the properly and completely assembled product only.

Required tools (not included): A Philips screwdriver, an open end wrench 14#, and a pair of gloves.

Use Precautions:

1. This product is not a toy. Do not allow children to play with or get access to this item.
2. Check carefully before use. Do not use if parts get loosened or damaged.
3. Use on flat and hard surfaces only.
4. Do not exceed the listed load-bearing capacity. Tighten all the knobs securely before placing weights on them. Be aware of the dynamic load-bearing capacity! Sudden load changes may temporarily cause excessive load, resulting in product failure.

SAVE THESE INSTRUCTIONS

Product Parameters

Part List

Attention: For additional information regarding the parts listed below, please refer to the assembly diagram in this manual. Unwrap and separate all parts in a clear work area.

Assembly Steps

Note: During installation, do not tighten the screws until all parts are installed.

Step 1: Assembly the Casters.

1. Turn over the Bottom shelf (Part 1).

2. Assemble the Casters (Parts 14 & 15) with Bolts (Part 16) as shown.

[Diagram Description: Bottom shelf (Part 1) is shown upside down, with four casters (two swivel with brake, two rigid) being attached to the corners using bolts (Part 16).]

Step 2: Assembly the Upright 8#.

1. Turn over the Bottom shelf (Part 1) and put the Casters on the ground.

2. Assemble the Uprights (Part 8) with Bolts (Part 17) and Nuts (Part 18). Pay attention to the Uprights' direction. Do not lock the bolts too tight initially.

[Diagram Description: The bottom shelf with casters is upright. Four upright posts (Part 8) are being attached vertically to the corners of the bottom shelf using bolts (Part 17) and nuts (Part 18).]

Step 3: Assembly the Middle shelf 2#.

1. Place the Middle shelf (Part 2) as shown and fix with Bolts (Part 17) and Nuts (Part 18). Attention: Initially, just fix the upper bolts on both sides and do not lock them too tight.

[Diagram Description: The middle shelf (Part 2) is being inserted between the uprights and attached using bolts (Part 17) and nuts (Part 18). A note indicates to only tighten upper bolts first.]

Step 4: Assembly the mounting plates 5#&6#, and Handle 10#.

1. Assemble the Left drawer mounting plate (Part 5), Right drawer mounting plate (Part 6), and Handle (Part 10) with Bolts (Part 17) as shown. Attention: The Left mounting plate has a lock. Ensure the ball bearing slides are in the same direction. Initially, just fix the upper bolts and do not lock them too tight.

[Diagram Description: The left and right drawer mounting plates (Parts 5 & 6) and the handle (Part 10) are being attached to the uprights. A close-up highlights the 'Lock Deadbolt' feature on the left plate and indicates 'Ball bearing slide at the same direction'.]

Step 5: Assembly the Pegboard 7# with bolt 17#.

1. Place the Pegboard (Part 7) as shown and fix with Bolts (Part 17). Do not lock the bolts too tight.

[Diagram Description: Two pegboards (Part 7) are being attached to the sides of the cart structure using bolts (Part 17).]

Step 6: Assembly the Beam 9# and Back board 11# with Bolt 17#.

1. Insert the Beam (Part 9) between the Upright and the drawer mounting plate as shown and fix with Bolts (Part 17). Pay attention to the ball bearing slide and the Top shelf's hole being in the same direction.

[Diagram Description: Beams (Part 9) are being inserted and attached between the uprights and drawer mounting plates. A note indicates to 'Inset the Beam between the Corner column and the Drawer mounting plate'.]

Step 7: Assembly the Back board 11#.

1. Place the Back board (Part 11) as shown and fix with Bolts (Part 17).

[Diagram Description: The back board (Part 11) is being attached to the rear of the cart structure using bolts (Part 17).]

Step 8: Assembly the Top shelf 3#.

1. Place the Top shelf (Part 3) as shown and fix with Bolts (Part 17). Then, tighten all the bolts securely.

[Diagram Description: The top shelf (Part 3) is being placed and secured with bolts (Part 17).]

Step 9: Assembly the Drawer 4# and EVA.

1. Pull out the ball bearing slides and insert the Drawer (Part 4) into them as shown. Then, place the Top EVA (Part 12) and Drawer EVA (Part 13) in their respective positions.

[Diagram Description: Drawers (Part 4) are being inserted into the ball bearing slides. EVA mats (Parts 12 & 13) are shown being placed on the top shelf and inside the drawers.]

Step 10: Assembly complete.

[Diagram Description: A final illustration shows the fully assembled VEVOR Tool Cart.]

Manufacturer and Representatives

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting, Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.