XZENT X-F285 Mounting Instruction

Compatibility List

FORD TRANSIT

Important Information

CAUTION

The installation of the XZENT system should be carried out by an authorized installer. Specific knowledge and tools are required for the installation. Incorrect installation can cause damage to the vehicle and the XZENT system.

Correct functioning can only be guaranteed when using XZENT original accessories included in the kit or optionally available. The XZENT system and original accessories must not be modified or altered in any way. Inappropriate actions can cause damage to the vehicle and the XZENT system.

NOTE

• The target vehicle must be equipped with the factory 1-DIN DAB/FM radio (Panasonic). The XZENT system is not compatible with vehicles equipped with an ex-works OE navigation system.
• These installation instructions apply to vehicle platforms listed in the compatibility list and as offered by the respective vehicle manufacturer. Deviating equipment and specific adjustments by motorhome manufacturers (e.g., battery, charging systems, power harness layout) are not covered. Contact the motorhome manufacturer for vehicle-specific questions.
• The XZENT system features an integrated DAB+ receiver. DAB+ and FM tuners connect directly to the vehicle's original rod antenna via an included adapter cable. For vehicles not listed, a suitable DAB/FM roof antenna (not included) may be required.
• Original multifunction steering wheel controls of compatible models are supported. No additional accessories are needed.
• Software updates are installed via a USB memory device. Ensure the XZENT system's USB connection remains accessible after installation (e.g., by installing a USB extension cable).
• For questions or issues with the XZENT system, contact the dealer where the device was purchased.

Scope of Delivery (Kit Includes)

Tools Required

• Torx screwdriver T25
• Release tool (contained in accessory set)
• Fabric tape

Installation Procedure

Dismantling and Preparation

1. The factory 1-DIN DAB/FM radio must first be removed for the installation of the X-F285 device. Insert the release keys (included in the accessory set) into the respective openings in the front panel of the 1-DIN factory radio.

   Illustration shows release keys being inserted into the factory radio.

2. Press both keys, without force, into their mechanical backstop.

3. Grab both unlocking keys and release the device with slight vertical up and down movements. Use the keys to pull the device out of the slot.

   Illustration shows the factory radio being pulled out using the release keys.

Installation

4. Disconnect the plugs of the power/loudspeaker, antenna, and USB connector cables on the backside of the 1-DIN radio.

   Illustration shows cables being disconnected from the rear of the factory radio.

5. Put the factory device aside. It is no longer needed for the installation of the X-F285 infotainer unit.

6. Prepare the plugs of the vehicle cables as shown in the illustration.

   Illustration shows vehicle cable plugs being prepared.

7. First, plug in the USB interface cable of the accessory set.

   Illustration shows USB interface cable connection.

8. Plug in the Fakra end of the antenna cable (No. 14) into the Fakra plug of the vehicle-side antenna cable.

   Install the GPS antenna in a suitable place, ensuring GPS reception is not adversely affected by metallic vehicle parts (e.g., thermal glazing). Route the connecting cable to the radio slot and connect it to the device.

   Illustration shows GPS antenna installation and Fakra antenna cable connection.

9. Now connect the main wiring harness to the main connector of the vehicle.

   If you wish to use the external Bluetooth microphone supplied, mount it now. Route the microphone cable to the radio slot. Adjust the microphone source in the device menu for external or internal microphone use.

   Illustration shows main wiring harness connection and microphone routing.

10. Check the fit of the connectors. Ensure the main connector is properly inserted.

11. Now plug in the SWC/CAN interface (No. 13) into the connector provided on the main wiring harness. Stow away the SWC/CAN box at the top left corner of the slot and route the cables to the left and right sides, utilizing the available space.

    Illustration shows SWC/CAN interface connection and cable management.

12. Connect all cable connectors to the backside of the device. Ensure all connectors are properly inserted.

    Illustration shows final cable connections to the rear of the XZENT device.

13. Hold the X-F285 device up in front of the slot and stow away cables to the left and right. Insert the device into the 1-DIN slot and push it gently until its body is completely inserted. Wiggle the device up and down until it clicks into place.

    Tip: To facilitate cable routing, uninstalling the tablet holder above the installation slot provides direct access.

    Illustration shows the X-F285 unit being inserted into the dashboard slot.

Commissioning

• Ensure all connectors at the rear of the unit have sufficient room and are not bent.
• Verify the power supply for the active antenna is connected (P.ANT lead connectors of the main harness).
• Secure connectors without retaining mechanisms with fabric tape.
• Ensure the vehicle is outdoors for GPS reception. Insert the navigation software SD card into the XZENT system's SD card slot and start it to establish a satellite fix (Sat-Fix). Do not move the vehicle until the Sat-Fix is established (may take 3-5 minutes).
• Press the NAV button to start navigation mode and select map view. Once your location is visible on the map, the Sat-Fix is complete.
• Perform a general functional test and basic settings. Ensure no error messages appear on the vehicle's display.

Electrical Characteristics

• Power supply: +12 V DC against vehicle ground
• External protection against internal short-circuit: 15 A Mini-ANL fuse

Operating currents*

• ACC off idle status: < 5.0 mA
• Audio / video playback (VOL 20): ~ 1.40 A
• GPS mode with active route guidance (VOL 20): ~ 1.55 A
• GPS mode with active route guidance (VOL 40): ~ 3.80 A

* @ 13.8 V operating voltage with front and rear 4 ohm loudspeakers connected to the device.

Connection Diagram

The rear of the XZENT X-F285 unit features several ports labeled A and B. These include connections for USB Media, SW update, RADIO, DAB, USB1, USB2, GPS, MIC, REVERSE, and P.CNTR. The diagram details the pin assignments for these connectors, including speaker outputs (FL+, FL-, RL+, RL-, FR+, FR-, RR+, RR-), line outputs, video outputs, AUX inputs, camera inputs, and microphone inputs.

Connector A: Primarily for USB, GPS, MIC, REVERSE, P.ANT_CON, P.CNTR, and other signal connections.

Connector B: Primarily for power, ground, ACC, ILLU, parking brake signal, and speaker outputs.

Detailed pinout tables are provided for both connectors, listing each pin number and its description (e.g., FL+, FL-, VIDEO OUT, CAMERA 1/2 IN, ACC, REVERSE).

Diagrams illustrate the rear panel ports, various cable connectors (USB 2.0, USB Mini, USB-4P), and detailed pinout tables for connectors A and B.