DELSJÖN Kitchen Mixer Tap

Product Overview

This document provides assembly and installation instructions for the IKEA DELSJÖN kitchen mixer tap.

Safety and Installation Regulations

? Installation must be carried out in accordance with industry regulations Säker Vatteninstallation.

⚠️ Switch off the main shut-off valve before changing the mixer tap.

Certifications: TG 1805, 1913, EN 817 | EN 1717.

RSK Number: 8312148.

Tools and Parts

Tools required:

• Caulking gun
• Adjustable wrench (2x)
• Allen key (included, part number 110084)
• Coin (for aerator)
• Mounting tool (included, part number 126908)

Specifications:

• Recommended Operating Temperature: Max. 60°C
• Recommended Operating Pressure: 1-5 bar
• Maximum Operating Pressure: 0.5-10 bar
• Connection size: G3/8 (R10)

Included Parts (refer to exploded view for details):

• Main tap body with spout and handle
• Flexible hoses
• Threaded rod (120143)
• Mounting plate (120087)
• Washers/Seals (120141, 120142)
• Nut (120172)
• Screw (10094227)
• Decorative cover (10094245)
• Aerator/Flow Guide (139269)

? For additional information, visit www.IKEA.com.

? If you encounter difficulties during assembly, consult the IKEA website or contact IKEA.

Assembly Instructions

Step 1

Attach the main tap body to the mounting surface. Insert the threaded rod (120143) from below through the tap body.

Diagram shows the threaded rod being inserted into the tap body.

Step 2

? Seal the open surfaces with silicone to prevent water from penetrating the worktop upon any leaks. Silicone is not included.

? Silicone sealant must be water- and mould-resistant and suitable for the installation, according to EN 15651-3, Class XS1.

Mounting hole diameter: Ø34-37 mm (Ø1 3/8 - 1 1/2").

Maximum thickness of mounting plate/gasket: 3 mm (1/8").

Maximum worktop thickness: 50 mm (2").

Diagram shows applying silicone sealant around the mounting hole on the worktop, then inserting the tap body and securing it from underneath with the mounting plate, nut, and tool.

Step 3

Rotate the spout. The spout can be rotated 120° to the left and 90° to the right.

Diagrams illustrate the rotation range of the spout.

Step 4

Secure the spout. Use the Allen key (110084) to tighten the screw (10094227) that secures the spout.

Diagram shows using an Allen key to tighten a screw on the tap body to fix the spout.

Step 5

Attach the spout to the tap body.

Diagram shows the spout being inserted into the tap body.

Step 6 & 7

Insert and rotate the decorative cover (10094245) into place.

Diagrams show a small decorative cover being inserted and rotated to lock into position.

Step 8

Remove and reattach the decorative cover.

Diagrams illustrate the process of removing and reattaching the decorative cover.

Step 9

Attach the spout to the tap body. Use the Allen key (110084) to tighten the screw (10094227).

Diagram shows the spout being attached and secured with a screw using the Allen key.

Step 10

Connect the flexible hoses to the water supply lines.

? The pipe connection needs to be flat and free from sharp edges.

⚠️ IMPORTANT! Do not tighten too hard: this can damage hoses/ pipes and washers.

Diagrams show connecting flexible hoses, with warnings against sharp edges and over-tightening. Some generic hose types are shown with a red cross, indicating they are not applicable or incorrect.

Before Use and Maintenance

Before Use

? Before use: Unscrew the Aerator/Flow Guide (139269) with a coin and allow the water to run freely for a few minutes. Then screw the Aerator/Flow Guide back in place up to the stop. DO NOT OVER TIGHTEN.

Diagram shows unscrewing the aerator with a coin, running water, and then screwing the aerator back in.

Maintenance

? Check at regular intervals to make sure that the installation is not leaking.

Exploded View and Parts List

The diagram below illustrates all components of the DELSJÖN kitchen mixer tap.

Diagram shows an exploded view of the tap, with each part labeled with its corresponding part number.

• Main tap body
• Spout
• Handle
• Aerator/Flow Guide (139269)
• Decorative cover (10094245)
• Screw (10094227)
• Allen key (110084)
• Threaded rod (120143)
• Mounting plate (120087)
• Washers/Seals (120141, 120142)
• Nut (120172)
• Mounting tool (126908)
• Flexible hoses (integrated)