Utilitech 3-Inch Automatic On/Off Magnetic LED Drawer Lights
Model: L-1102-B-02 | Item #: 5703148
Product Overview
These Utilitech LED drawer lights provide automatic illumination for drawers and cabinets. They feature a magnetic design for easy installation and an automatic on/off function activated by a proximity sensor. The lights are 3 inches (7.62 cm) in length.
Key Features:
- Automatic On/Off operation via proximity sensor
- Magnetic mounting system
- 3-inch (7.62 cm) size
- Requires a 5V 1A power adapter (not included)
Customer Support:
For questions, problems, or missing parts, please contact Utilitech customer service at 1-866-994-4148 (8 a.m. - 8 p.m. EST, Monday - Sunday) or email ascs@lowes.com.
Getting Started:
If you feel confident, start your next project!
Package Contents
The package typically includes:
- (A) LED Light Unit (x2)
- (B) Mounting Bracket (x2)
- (C) Adhesive Strips (x2)
- (D) Connecting Wire (x1)
Installation Guide
Preparation:
Before beginning assembly, ensure all parts are present by comparing them with the package contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated assembly time is 2 minutes, and no tools are required.
Mounting the Bracket:
- Take a mounting bracket (B) and peel off the protective film from the side without adhesive.
- Peel off the adhesive tape (C) from the bracket.
- Firmly attach the bracket (B) to the desired installation surface (e.g., drawer, cabinet) using the adhesive tape (C). Ensure the surface is clean and flat.
Attaching the Light and Sensor Placement:
The LED light unit (A) magnetically attaches to the mounted bracket (B).
Sensor Range: For optimal performance, the distance between the proximity sensor on the light unit and the reflective surface (e.g., drawer front) should be approximately 0.2 to 1.5 inches (0.5 cm to 4 cm). For best results, install on reflective surfaces made of wood or iron, with a sensor distance of 0.4 to 0.8 inches (1 cm to 2 cm). Adjust the distance if using other reflective materials.
Power Connection:
Connect a 5V 1A power adapter (not included) to the power port on the LED light unit (A).
Switch Functions:
- ON: The light remains continuously illuminated.
- OFF: The light remains off.
- AUTO ON/OFF: The light turns on when the sensor detects motion within range and turns off when the sensor no longer detects motion or the object is too close (within 0.2-1.5 inches).
Care and Maintenance
- Keep the installation area as dry as possible to prevent moisture from affecting the lamp.
- Periodically wipe the surface of the lamp with a dry, soft cloth or a slightly damp cotton cloth to remove dust and stains.
Troubleshooting
| Issue | Possible Cause | Corrective Action |
|---|---|---|
| The drawer light does not turn on. | The battery is out of power or the switch is positioned "OFF". | Charge the product for at least 10 minutes and verify the switch is in the correct position. |
| The sensor is out of range. | The sensor is too far from or too close to the reflective surface. | Ensure the distance between the sensor and the reflective surface is approximately 0.2in-1.5in (0.5 cm - 4 cm). |
Safety Information
Warnings
- Read and understand this entire manual before attempting to assemble, operate, or install the product.
- Carefully check the wall or panel surface at the pre-installation location to ensure that it is completely flat and without convexity. Any significant unevenness may cause the device to loosen, move, or even fall off during use, causing damage to the device.
- Thoroughly clean the installation area before installation to remove all dust, oil, paint residue, adhesive, and other dirt. These impurities may affect the adhesion between the device and the mounting surface, resulting in loose fixation, or aggravated loosening due to factors such as moisture, thermal expansion, and contraction during long-term use.
- Fully charge the fixture before initial use. A red light indicates charging; the red light will turn off when fully charged.
- For battery products, the brightness will dim as the battery power decreases. If the current brightness cannot meet your lighting needs, fully charge the battery, then use.
- DO NOT look directly at LED light sources.
- DO NOT use this product near highly flammable materials, liquids, and gases.
- Installation should follow local/national electrical codes.
- DO NOT use it if there is any damage to the fixture or wires.
Precautions
- Determine the installation position, avoiding water sources, gas pipelines, and flammable items to ensure safety.
- Make sure there is a certain amount of heat dissipation space around the lamp after installation. The heat generated during long-term operation needs to be effectively dissipated; otherwise, the service life of the lamp may be affected.
Battery Care
When the fixture is discharged and turned off, please finish charging within 7-15 days to avoid affecting the life of the battery.
To ensure the life of the fixture, charging and discharging should be carried out under the following conditions: (1) the fixture input 5V; (2) the charging ambient temperature: between 10°C-40°C; (3) the operating ambient temperature should be maintained between: -10°C-50°C.
FCC Compliance
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
This product has a valid warranty period of two years. Instances of normal wear and tear, damage caused by abuse, misuse, alteration, or failure to follow instructions or proper maintenance are not covered.
