Allen + Roth 3-Light Vanity Light

Care and Maintenance

Shut off the main power supply before performing any maintenance. Periodically clean the fixture with a mild, non-abrasive glass cleaner and a soft cloth. Avoid using solvents or cleaners with abrasive agents, and do not spray liquid cleaner directly onto the bulb or wiring.

For questions, problems, or missing parts, contact Allen + Roth customer service at 866-439-9800, Monday-Sunday, 8 a.m. - 8 p.m. EST, or email ascs@lowes.com.

For more information, visit www.lowes.com and refer to the Guides & Documents tab on the product page.

Safety Information

WARNING

• Ensure the electrical system has a proper grounding means. Failure to do so could result in electrical shock if wires become broken or loose.
• Wire connectors are not designed to support the fixture's weight. Suspending the fixture by supply wires and connectors can cause it to fall, leading to injury or fire hazards.

CAUTION

• Do not use bulbs with a wattage exceeding the maximum specified on the fixture to prevent overheating and fire risks.
• Ensure all electrical connections comply with local codes, ordinances, and the National Electrical Code (ANSI/NFPA 70-199). Consult a qualified electrician if you are unfamiliar with electrical wiring.
• Turn off electricity at the main fuse box or circuit breaker before starting installation.
• All fixtures must be mounted to an outlet box supported by the building structure. Do not mount to drywall alone, as the fixture may fall and cause injury.
• Do not connect the fixture's ground wire (green or bare) to the black (hot) or white (neutral) supply wire.
• Do not connect this fixture to an electrical system that lacks equipment grounding.

Warranty

Allen + Roth warrants its lighting fixtures against defects in materials and workmanship for three (3) years from the date of purchase. If the product is found defective within this period, present the bill of sale and the product in its original carton to the place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase price. The consumer is responsible for all installation and removal costs. This warranty does not cover defects due to misuse, accidental damage, or improper handling/installation. It specifically excludes liability for direct, incidental, or consequential damages. Some states may not allow these exclusions, so the above limitations may not apply to you. This warranty grants specific rights, and you may have other rights that vary by state.

Installation Overview

Preparation

Before assembly, verify all parts are present by comparing them with the package contents and hardware lists. Do not assemble if parts are missing or damaged.

Estimated Assembly Time: 35 minutes.

Tools Required (Not Included)

• Screwdriver
• Wire Strippers
• Pliers
• Voltage Tester

Package Contents

• (A) Fixture (preassembled)
• (B) Mounting Bracket
• (C) Hex Nuts (x2)
• (D) Long Screws (x2)
• (E) Short Screws (x2)
• (F) Glass Shades (x3)
• (G) Mounting Screws (x3)

Hardware Contents

• (AA) Wire Connectors (x3)
• (QQ) Ground Screw (x2)

Installation Steps

1. Turn OFF the electrical power at the main fuse or circuit breaker.
2. Attach the mounting bracket (B) to the outlet box using the provided mounting screws (G).
3. Note: Use the center screw to ensure mounting screws (D) are aligned perpendicularly to the horizon, as they will determine the fixture's orientation.
4. Loosen the ground screw on the mounting bracket (B). Wrap the bare wire from the fixture (A) around the ground screw and tighten it.
5. Connect the wires:
   • Connect the black wire from the fixture (A) to the black (hot) supply wire.
   • Connect the white wire from the fixture (A) to the white (neutral) supply wire.
   • Connect the bare wire from the fixture (A) to the bare/green (ground) supply wire.
   If supply wire colors differ, consult a professional electrician.
6. Secure the fixture (A) to the mounting bracket (B) using the long screws (D) and hex nuts (C). Adjust hex nuts (C) as needed to ensure a secure fit.
7. Attach the glass shades (F) to the fixture (A) using the short screws (E).
8. Install bulbs (not included) with a maximum of 60W per socket.
9. Restore power at the main fuse or circuit breaker.