Allen + Roth 3-Light Vanity Light

Care and Maintenance

Shut off the main power supply before performing any maintenance. Periodically clean the fixture using a mild, non-abrasive glass cleaner and a soft cloth. Do NOT use solvents or cleaners containing abrasive agents, and do not spray liquid cleaner directly onto the bulb or wiring.

Product Information

Thank you for purchasing this Allen + Roth product. These instructions are designed to ensure you spend your time enjoying the product. For more information, visit Lowes.com and refer to the Guides & Documents tab on the product's page.

Visit www.lowes.com for more information.

Safety Information

General Safety

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

Warnings

• Installing a fixture into an electrical system without proper grounding can lead to electrical shock if wires become broken or loose.
• Wire connectors will not support the weight of this fixture. Suspending the fixture by supply wires and connectors can cause it to fall, leading to injury or fire.

Cautions

• Do not use bulbs with a wattage higher than the maximum stated on the fixture to prevent fire risks.
• Ensure all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. Hire a qualified electrician if you are unfamiliar with electrical wiring.
• Turn off electricity at the main fuse box or circuit breaker box before beginning installation.
• All fixtures must be mounted to an outlet box supported by the building structure. Do not support the fixture by drywall alone, as it may fall and cause injury.
• Do not connect the fixture's ground wire (green or bare) to the black (hot) or white (neutral) supply wire.
• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.

Warranty

The manufacturer warrants all lighting fixtures against defects in materials and workmanship for three (3) years from the date of purchase. If the product is found to be defective within this period, return it with a copy of the bill of sale to the place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase price. Costs of installation and removal are the consumer's responsibility. This warranty does not cover defects due to misuse, accidental damage, or improper handling/installation. It specifically excludes liability for direct, incidental, or consequential damages. Some states may not allow these limitations, so the above may not apply. This warranty grants specific rights, and you may have other rights that vary by state.

Preparation

Before assembly, ensure all parts are present by comparing them with the package contents and hardware lists. Do not attempt assembly if any part is missing or damaged.

Estimated Assembly Time: 35 minutes

Tools Required (Not Included):

• Screwdriver
• Wire strippers
• Wire connectors
• Ladder

Package Contents

• (A) Fixture
• (B) Mounting Bracket
• (C) Hex Nuts (x2)
• (D) Mounting Screws (x2)
• (E) Wire Connectors (x2)
• (F) Bulbs (not included)
• (G) Decorative Nuts (x3)

Hardware Contents

• (AA) Ground Screw (x3)
• (QQ) Screws (x2)

Installation Overview

1. Turn OFF the electrical power at the main fuse or circuit breaker.
2. Attach the mounting bracket (B) to the outlet box using the provided screws (QQ).
3. Feed the fixture wires through the center of the mounting bracket (B).
4. Loosen the ground screw on the mounting bracket (B) and wrap the bare wire from the fixture (A) around the ground screw. Tighten the ground screw.
5. Connect the wires: Black fixture wire to black supply wire (hot), white fixture wire to white supply wire (neutral), and bare fixture wire to bare/green supply wire (ground). Use wire connectors (E) for secure connections. If supply wire colors differ, consult a professional electrician.
6. Slide the fixture (A) onto the mounting screws (D), ensuring the screws are perpendicular to the horizon for a level installation. Adjust hex nuts (C) on the screws (D) if necessary for a secure fit.
7. Secure the fixture (A) using the decorative nuts (G).
8. Install bulbs (F) (not included) with a maximum of 60W per socket.
9. Restore power at the main fuse or circuit breaker.