Cycplus M2 Cycling Computer

GPS Localization - Quick User Guide

For satellite signal reception, ensure the device is used in an open area without obstructions.

1. Press the L1 button `[▶️]` to turn on the device.
2. GPS signal acquisition takes a few minutes. The ?️ icon indicates the device is ready.
3. Press the L1 button `[▶️]` again to start recording. The ▶️ icon will appear after recording starts.
4. Press and hold the L2 button `[?]` to save recording data. The ? icon will disappear after saving.
5. Press and hold the L1 button `[❌]` to turn off the device.

Introduction

Model:

M2

Screen Size:

2.5-inch LCD display

Product Size:

69*69*22 mm

Product Weight:

68 g

Battery:

1100 mAh 3.7V

Memory Capacity:

150 hours

Working Time:

30-35 hours

Charging Mode:

Type-C

Charging Time:

Approx. 3.5 hours

App Connection:

Bluetooth 5.0

Peripheral Connection:

ANT+

Supported Peripherals:

Speed sensor, cadence sensor, heart rate monitor, power meter.

Water Resistance:

IPX6 (rain-resistant, not submersible) ?

Current Data Display

The main display shows real-time cycling data. Key metrics include:

• Speed: Current speed (e.g., 31.2 KMH)
• Time: Elapsed time for the current ride (e.g., 53:36)
• Distance: Total distance covered (e.g., 335.6 KM)
• Heart Rate: Current heart rate (e.g., 142 bpm) ❤️
• Cadence: Current pedaling cadence (e.g., 104 rpm) ⚙️
• Temperature: Ambient temperature (e.g., 28°C) ?️
• Battery Status: ?
• GPS Status: ?️
• Lap: Current lap information
• Current Time: 10:28

Average and Maximum Data

The device also displays average and maximum values for various metrics recorded during rides, such as speed, heart rate, cadence, and temperature.

Settings

Access the settings menu by pressing and holding the R1 button `[R1]`. Navigate through the 8 settings pages by pressing the R1 button `[R1]`. Press and hold the R1 button `[R1]` again to return to the main screen after completing your settings.

Connecting Ant+ Sensors

To connect ANT+ sensors (like speed, cadence, or heart rate monitors):

• Press the L1 button `[L1]` to start searching for ANT+ sensors.
• Data from connected sensors will be displayed.
• If a sensor is not connected, its number will blink.
• The device will automatically return to the main screen after 10 seconds.

Wheel Circumference Settings

To set the wheel circumference:

• Start setting: Press the L1 button `[L1]`.
• Adjust number: Press the R1 button `[R1]`.
• Switch digit: Press the L2 button `[L2]`.
• Finish setting: Press the L1 button `[L1]`.

Time Zone Settings

To set the time zone:

• Start setting: Press the L1 button `[L1]`.
• Change time zone: Press the R1 button `[R1]`.
• Finish setting: Press the L1 button `[L1]`.
• The time zone digits will blink during adjustment.

Speed Unit Settings

To set the speed unit:

• Start setting: Press the L1 button `[L1]`.
• Switch between KMH and MPH: Press the R1 button `[R1]`.
• Finish setting: Press the L1 button `[L1]`. The selected unit will blink.

Temperature Unit Settings

To set the temperature unit:

• Start setting: Press the L1 button `[L1]`.
• Switch between °C and °F: Press the R1 button `[R1]`.
• Finish setting: Press the L1 button `[L1]`. The selected unit will blink.

Factory Reset

To reset the device to factory settings:

• Start setting: Press the L1 button `[L1]`.
• Long press the L2 button `[L2]` to restore default settings and turn off the computer.

Odometer Settings

To set the odometer:

• Start setting: Press the L1 button `[L1]`. All digits will blink.
• Edit digit: Press the R1 button `[R1]`. The digit to be set will blink.
• Switch digit: Press the L2 button `[L2]`. The digit to be set will blink.
• Finish setting: Press the L1 button `[L1]`. All numbers will blink.

Connecting to XOSS App

Download the XOSS app from the Google Play Store or Apple App Store. Register using your email address. Ensure Bluetooth is enabled on your device.

Connecting to M1

Open the XOSS app, select "CYCPLUS M2", and tap to connect.

Connecting STRAVA/Training Peaks

Find Strava/Training Peaks in your personal files and click "Connect". Log in using your account and password. Note: Google and Facebook login are not supported.

Updating Data and Analyzing

Click "Synchronize" to sync your ride data with the app. If the Strava app is connected, data will sync automatically. Select an activity on the training page to view detailed cycling data.

Caution

• Data Recording: Press the L1 button `[▶️]` to start recording. Remember to hold the L2 button `[?]` to save the recording after finishing your ride.
• Memory: When the device's memory is full, it will automatically overwrite the oldest recordings in chronological order.

Package Contents

The package includes:

• GPS Cycling Computer
• Mount for Cycling Computer
• Rubber Pad
• User Manual
• Type-C Charging Cable

Installation Information

1. CYCPLUS Z1/Z2 mount for cycling computer (must be purchased separately).
2. Use the mount for the cycling computer. Attach the mount securely using the rubber band.

Manufacturer Information

Chengdu Chendian Intelligent Technology Co., Ltd.

Tire Circumference Graph

The following table provides tire sizes and their corresponding circumferences for informational purposes. The actual circumference may vary depending on tire pressure.

EU Declaration of Conformity

[Chengdu Chendian Intelligent Technology Co., Ltd.] hereby declares that the radio equipment type [Cycplus M2 Cycling Computer] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://files.innpro.pl/Cycplus

Manufacturer: Unit2, Building 2, No. 88, Tianchen Road, Chengdu, Sichuan, CN, Postal Code: 611730.

Radio frequency: 2400MHz-2483.5MHz.

Maximum radio frequency power: 0 dBm.

Environmental Protection

Electronic waste marked in accordance with the European Union directive must not be disposed of with other municipal waste. It is subject to separate collection and recycling at designated locations. By ensuring its proper disposal, you prevent potential negative consequences for the environment and human health. The collection system for used equipment complies with local environmental protection regulations for waste disposal. Detailed information on this topic can be obtained from the local authority, processing plant, or the store where the product was purchased. The product complies with the requirements of the so-called new approach directives of the European Union (EU) in the areas of safety, health, and the environment, which specify hazards that should be identified and eliminated.

This document is a translation of the original user manual provided by the manufacturer.

The user or a specialized service center must regularly maintain (clean) the product at the user's expense. If the user manual does not provide information on necessary cyclical maintenance or service operations, it is necessary to regularly, at least once a week, evaluate any deviation of the product's physical state from that of a new product. If any deviation is detected or found, maintenance (cleaning) or service measures must be carried out immediately. Failure to perform proper maintenance (cleaning) and failure to respond to a detected deviation may result in permanent damage to the product. The guarantor is not responsible for damages incurred due to negligence.

Importer Information

Importer: INNPRO Robert Błędowski sp. z o.o.

Address: Rudzka 65c, 44-200 Rybnik, Poland.

Contact: tel. +48 533 234 303, hurt@innpro.pl, www.innpro.pl.

For LI-ION Batteries

The appliance is equipped with a LI-ION (lithium-ion) battery, which ages over time and with use due to its financial and chemical structure. The manufacturer states the maximum operating time of the device under laboratory conditions, where optimal operating conditions exist for the device and the battery itself is new and fully charged. The operating time may actually differ from the time declared in the offer and is not a device defect, but a product characteristic. To preserve maximum battery life, it is not recommended to discharge the battery below 3.18 V or 15% of its total capacity. Lower values, for example 2.5 V per cell, will permanently damage it, and the warranty will not cover this. If you do not use the battery or the entire device for more than one month, charge the battery to 50% and check its charge level regularly every two months. Store the battery and device in a dry place, away from sunlight and negative temperatures.

For LIPO Batteries

The device is equipped with a LI PO (lithium-polymer) battery, which ages over time and with use due to its final and chemical structure. The manufacturer states the maximum operating time of the device under laboratory conditions, where optimal operating conditions exist for the device and the battery itself is new and fully charged. The operating time may actually differ from the time declared in the offer and is not a device defect, but a product characteristic. To preserve maximum battery life, it is not recommended to discharge the battery below 3.5 V or 5% of its total capacity. Lower values, for example 3.2 V per cell, will permanently damage it, and the warranty will not cover this. If you do not use the battery or the entire device for more than one month, charge the battery to 50% and check its charge level regularly every two months. Store the battery and device in a dry place, away from sunlight and negative temperatures.

Safety Precautions

• Before charging, check that the device contacts are clean.
• Do not leave the device unattended during use and charging.
• Ensure that you can quickly disconnect the device from the power source in case of emergency.
• Never expose the device to high temperatures.
• Charge the device in a dry and well-ventilated area, away from surroundings. Maintain a minimum distance of 1 meter from other objects.
• Never cover the device while charging.
• Never use power adapters, charging stations, cables, etc., without the manufacturer's recommendation and approval.
• Be mindful of your property; the device is equipped with batteries that are difficult to extinguish. Keep a fire extinguisher handy.

Warranty

The warranty is void in case of changes and/or modifications to the product. The manufacturer is not responsible for damages incurred from improper use of this product.

Disposal

• Dispose of this product at appropriate collection points. Do not discard this product with municipal waste.
• For more information, contact the seller or local authorities responsible for waste management.

Documentation

This product has been manufactured and is supplied in accordance with all applicable regulations and directives in all member states of the European Union. It also meets all relevant specifications and regulations in the country of sale. Official documentation can be obtained upon request. Official documentation includes (but is not limited to) the Declaration of Conformity, Material Safety Data Sheets, and product test reports.

Disclaimer

Product design and specifications may be changed without prior notice. All logos and trade names are registered trademarks of their respective owners and are protected by law.