Pelonis 2 in 1 Turbo Heater + Fan

Important Safety Instructions

WARNING: When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, injury to persons, and hyperthermia, including the following:

• Read all instructions before using this heater.

CAUTION:

• Please read and save these important safety instructions.
• This heater is not intended for use in bathrooms, laundry areas, and similar moist indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature, as it could result in an electric shock hazard.
• This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
• It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace a loose or worn outlet.
• To disconnect the heater, first turn controls to off, then remove the plug from the outlet. Never pull by the cord.
• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).

WARNING:

• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, always use handles when moving this heater. Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalids, and whenever the heater is left operating and unattended.
• Always unplug the heater when not in use.
• Do not operate any heater with a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any manner. Discard the heater or return it to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
• Do not use the heater outdoors.
• Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from traffic areas and where it will not be tripped over.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock or fire, or damage the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
• A heater has hot parts and parts that produce arcs or sparks inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• The output of this heater may vary, and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
• Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
• To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave the product running unattended in a confined space around infants or individuals with reduced physical, sensory, or mental capabilities.

SAVE THESE INSTRUCTIONS

Specifications

Power Regulation Range

Product Overview

The Pelonis 2-in-1 Turbo Heater + Fan (Model PSH23FT4DBB) is a compact appliance designed for both heating and cooling. The unit features a front grille and a tilting base.

Key Parts:

• Control Panel: Located on the top of the unit, used for operating the heater.
• Power Indicator Light: Illuminates when the unit is plugged in and turned on.
• Safety Grille: Protects the internal fan and heating elements.
• Base: Provides stability and allows the unit to tilt.
• Remote Control: Allows for operation from a distance.

Illustrations in this manual are for explanatory purposes only. Any discrepancies between the real object and the illustration should defer to the real product.

Operation Instructions

Check Before Turning On The Machine

• Ensure the power wire is in good condition.
• The product uses a 120V AC power supply. Before use, confirm that the power socket meets local requirements with a safe grounding device. If not, replace it with a qualified socket.

Panel Operation & Display

The unit's control panel includes a display area, timer, temperature setting controls, mode selection, and an ON/OFF button.

Button Functions:

• ON/OFF Button: Press to turn the unit on from standby, or press to switch to standby from an operating state.
• MODE Button (M): In power-on state, press to cycle through operating modes: High Heat (H3) → Middle Heat (H2) → Low Heat (H1) → High Cool (C2) → Low Cool (C1) → High Heat.
• LED Display Control: After powering on, press and hold the MODE (M) and "+" buttons for three seconds to turn the LED display screen on or off.
• Temperature Setting Button (?️): When the machine is in heater mode, press this button to select a temperature between 45-95°F (7-35°C). If the room temperature exceeds the set temperature by 4°F (2°C), the machine will automatically switch to standby mode. It will resume heating when the temperature drops below the set point.
• TIMER Button (⏱️):
  • Timing Stop: To set an automatic power-off timer, press the timer button to select the desired time in one-hour intervals, up to 8 hours.
  • Timing Start: To set an automatic power-on timer from standby mode, press the timer button to select the desired time in one-hour intervals, up to 8 hours.
  • Cancel Timer: To cancel timer operation, press and hold the timer button for three seconds.

Display Lights:

• Power Light: Indicates the unit is connected to the power supply.
• Cooling Air Light (❄️): Illuminates when the unit is on and operating in cooling mode; turns off in other modes.
• Heating Air Light (?): Illuminates when the unit is on and operating in heating mode; turns off in other modes.
• Timer Light (⏱️): Illuminates when a timer is set for power on/off.
• LED Nixie Tube (8.8): Displays the working state, error codes, and timer settings.

Air Flow Direction Adjustment

The unit is equipped with a pivoting head that allows selection of 5 different angles:

Angles: 0°, 18°, 38°, 53°, 75°

When the unit is set to low or middle heat speed and the desired tilt angle is 38°, 53°, or 75°, it will automatically switch to high heat speed. When adjusting the angle, do not place your hand on the safety grille to prevent injury.

Remote Controller

The remote control should be used within 16 ft (approx. 5 meters) of the product's front and within a 30-degree deviation angle.

Batteries contain heavy metals and should be recycled separately.

Remote Buttons: ON/OFF, Mode (M), Timer, Temperature Adjust (+/-).

Battery Installation

The remote control requires 2 AAA batteries (included). Please install them before use:

1. Slide open the battery compartment cover.
2. Insert the batteries, ensuring correct polarity (+/-).
3. Slide the battery cover back into place.

Battery Type: Use manganese or alkaline AAA batteries (1.5V).

Battery Warnings

• Do not dispose of batteries in fire; they may explode or leak.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
• Non-rechargeable batteries are not to be recharged.
• Batteries must be inserted with the correct polarity.
• Exhausted batteries must be removed from the product.
• Batteries must be removed from the remote controller before disposal and disposed of safely.

Protection When Temperature Sensor has Short Circuit or Open Circuit

If the temperature sensor experiences a short circuit or open circuit, the digital screen will display error codes "E2" or "E1" and flicker continuously. Operational button inputs will be ineffective, and a buzzer will sound 10 times.

Safety Protection

• Start-up Protection: If the room temperature (TH) exceeds 131°F (55°C) during startup, the appliance will automatically shut down all outputs. The digital display will flash for 75 seconds, then continuously show "FF". No buttons will function. To exit this mode, power down and manually unplug the appliance.
• Thermal Cut-off: When the unit is operating and the internal temperature exceeds the thermal cut-off threshold, it will automatically stop working. The digital screen and indicator lights will turn off. To resolve this, manually unplug the appliance, wait for it to cool down, and then plug it back in to restart.

Cleaning and Maintenance

It is recommended to clean the heater at least once during the operating season for optimal performance. ALWAYS TURN THE POWER SWITCH OFF AND UNPLUG THE HEATER BEFORE CLEANING. Save the original box for off-season storage.

• Turn the heater "OFF", unplug it, and wait for it to cool down.
• Use a dry cloth to clean only the external surfaces of the heater.
• Do not use any cleaning agents or detergents.
• Never immerse the heater in water.
• Pack the heater in its original carton and store it in a cool, dry place.

Troubleshooting

The appliance may encounter errors and malfunctions. The following table lists possible causes and solutions:

Service and Support

In the event of a warranty claim or if service is required for this product, please contact Midea America Corp at the following:

Toll Free: 1-866-646-4332

For questions or comments, please write to:
Midea America Corp
300 Kimball Drive,
Parsippany NJ 07054

For your records, staple your sales receipt to this manual and record the following:

DATE OF PURCHASE: [____________________]

PLACE OF PURCHASE: [____________________]

(STAPLE SALES RECEIPT HERE)

NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS

PRINTED IN CHINA

1 Year Limited Warranty

Midea America Corporation warrants to the original retail purchaser that each new Fan Heater shall be free of defects in material and workmanship for a period of one (1) year from the date of original purchase. This one (1) year warranty is limited to the motor and electric element.

In the event of malfunctions or failure of your Fan Heater, deliver or send the Fan Heater, postage prepaid, along with PROOF OF PURCHASE, within the one (1) year warranty period, to Midea America Corporation. Midea America Corporation reserves the right to inspect the claimed defective part(s) to determine if the defect or malfunction is covered by this warranty. Midea America Corporation shall, within sixty (60) days after receipt of the product, at its option, repair and/or replace the defective part(s) free of charge. This warranty shall only cover defects arising from normal usage.

Midea America Corporation assumes no responsibility whatsoever if the Fan Heater should fail during the warranty period due to:

• Misuse, negligence, physical damage, or accidents.
• Lack of maintenance (refer to maintenance instructions).
• Repair by any unauthorized party during the warranty period.
• Damage caused by connection to an improper input voltage (refer to the specification label on your Fan Heater).

Midea America Corporation makes no other warranties or representations, express or implied, except those contained herein. No representative or dealer is authorized to assume any other liability regarding the Fan Heater. The duration of implied warranties granted under State law, including warranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of the express warranty granted hereunder. Midea America Corporation shall in no event be liable for direct, indirect, special, or consequential damages.

Some states do not allow limitations on how long an implied warranty lasts, and/or the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.