Pelonis Digital Tower Ceramic Heater

Important Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, and hyperthermia, including the following:

1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surface. If provided, always use handles when moving this heater. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 meters) from the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4. Always unplug the heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater or return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use the heater outdoors.
7. This heater is not intended for use in bathroom, laundry areas and similar moist indoor locations. Never locate heater where it may fall into a bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
9. CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. To do so could result in an electric shock hazard.
10. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
11. CAUTION: It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.
12. To disconnect the heater, first turn controls to off, then remove plug from outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surface, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
17. CAUTION: Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).
18. The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
19. CAUTION: To prevent electric shock, match wide blade of plug to wide slot and fully insert.
20. Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
21. To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a confined space around infants, or individuals with reduced physical, sensory, or mental capabilities.
22. "SAVE THESE INSTRUCTIONS"

Part Identification

Description of the Pelonis Digital Tower Ceramic Heater and its remote control:

• Heater: A tall, black, tower-style unit with a perforated grille on the front. It has a control panel and display screen at the top, and a stable base.
• Remote Control: A small, black, handheld device used to operate the heater from a distance.

The heater components are labeled as:

• Control panel
• Display screen
• Grille
• Front cover
• Rear cover
• Base

The control panel and remote control feature the following functions:

• Display screen: Shows operating status, temperature, and timer settings.
• [eco] symbol: Indicates ECO mode.
• [Swing] button: Activates or deactivates the oscillation function.
• [Timer] button: Sets the timer for auto shut-off or delayed start.
• [-] button: Decreases temperature or timer setting.
• [+] button: Increases temperature or timer setting.
• [Mode] button: Cycles through heating modes (High, Low, ECO).
• [ON/OFF] button: Powers the heater on or off.

Operating Instructions

Check before turning on the machine

1. Check if the power wire is under good condition.
2. The product uses 120V AC power supply. Confirm that the power socket meets local grounding requirements. If not, replace with a qualified socket.

Start the machine

Plug the unit into a grounded 120V outlet. The power light will illuminate. Press the [ON/OFF] button (on the unit or remote) to start. The heater will supply air at high power, and the digital screen will display "HI".

Function setting

Repeatedly press the [Mode] button to cycle through the heating modes: "high gear - low gear - ECO mode".

Temperature setting

In ECO mode, press [+] or [-] to set the desired temperature (range: 40-95°F). If the room temperature exceeds the set temperature by 4°F, the machine stops and enters standby mode. It will resume heating when the temperature drops below the set point.

Timing function

Timing stop

When the heater is on, press the [Timer] button to enter the timing stop state (0-8 hours). Use [+] to increase and [-] to decrease the stop time.

Timing start

When the heater is in standby mode, press the [Timer] button to enter the reservation start mode (0-8 hours). Use [+] to increase and [-] to decrease the start time.

Oscillation function

While the heater is operating, press the [Swing] button to activate oscillation. Pressing it again turns it off. Oscillation stops when heating stops.

Temperature sensor protection

If the temperature sensor has a short circuit or open circuit, the display will show "E1" or "E2" and flicker. All button operations will be invalid, and the buzzer will sound 10 times.

Safety protection

If the room temperature exceeds 122°F, all outputs will shut off. The display will show "FF" and flash once per second. Pressing any key will not work; power down to exit protection.

Tip-over switch

As a safety measure, the unit will shut off automatically if knocked over. Turn the heater off, stand it upright, then switch it back on.

ECO energy saving function

Select ECO mode and set the temperature. The heater will adjust its heating level by comparing ambient temperature with the set temperature.

Remote controller

The remote control functions are the same as the unit's control panel.

Remote control buttons:

• [ON/OFF] button
• [Mode] button
• [+] Temperature / Timer increase
• [-] Temperature / Timer decrease
• [Timer] button
• [Swing] button

Do not mix old and new batteries, or alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.

Main Technology Specifications

Power supply: AC 120V ~ 60Hz

Troubleshooting

If the product does not operate or does not operate properly, check the following:

Cleaning and Storage

Clean the heater at least once during the operating season for optimum performance. ALWAYS TURN THE POWER SWITCH OFF AND UNPLUG THE HEATER BEFORE CLEANING. Save the box for off-season storage.

• Turn the heater "OFF", unplug it, and wait for it to cool down.
• Use a dry cloth to clean only external surfaces of the heater.
• Do not use any cleaning agents or detergents.
• Never immerse the heater in water.
• Pack the heater in the original carton and store it in a cool and dry place.

Service & Support

For warranty claims or service, contact:

Toll Free: 1-866-646-4332

For questions or comments, write to:

Midea America Corp
300 Kimball Drive,
Parsippany NJ 07054
Phone: 866 646 4332

For your records, staple your sales receipt to this manual and record the following:

DATE OF PURCHASE: _________________________

PLACE OF PURCHASE: _________________________

(STAPLE SALES RECEIPT HERE)

NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS.

PRINTED IN CHINA

One (1) Year Limited Warranty

Please read all instructions before attempting to use this product.

Midea America Corporation warrants to the original purchaser that each new Fan-forced heater shall be free of defects in material and workmanship for a period of one (1) year from the date of original purchase. This warranty is limited to the heating elements, motor, and electric control circuit board.

In case of malfunction or failure, deliver or send the heater, postage prepaid, along with PROOF OF PURCHASE, within the warranty period to Midea America Corporation. Midea America Corporation reserves the right to inspect the claimed defective part or parts to determine if the defect is covered. Midea America Corporation shall, within sixty (60) days after receipt, at its option, repair and/or replace the defective part or parts free of charge. This warranty covers defects arising from normal usage.

Midea America Corporation assumes no responsibility if the heater fails during the warranty period due to:

• Misuse, negligence, physical damage or accidents.
• Lack of maintenance (see instructions for proper maintenance).
• Repair by any unauthorized party.
• Damage caused by connection to an improper input voltage (see specification label on your heater).

Midea America Corporation makes no further warranties or representations, express or implied. No representative or dealer is authorized to assume any other liability. Implied warranties are limited in duration to the express warranty period. Midea America Corporation shall not be liable for direct, indirect, special, or consequential damages.

Some states do not allow limitations on implied warranty duration, or exclusions. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Warranty Extension Offer: Free 3 months extension of the original limited warranty period. Simply text a picture of your proof of purchase to: 1-844-224-1614. The warranty extension is for the three months immediately following the completion of the product's original warranty period.