Montarbo WIND PRO 215A Owner's Manual

Introduction

The Montarbo WIND PRO 215A is an amplified acoustic loudspeaker designed to deliver exceptional performance in terms of power and quality. It features a "Quasi 3-way" acoustic design and a sophisticated audio signal processing system, setting a new standard for point-source sound. This system includes a 1.4" high-frequency coaxially horn-loaded driver, a 15" transducer with a 3" voice coil, and an additional 15" woofer with a 3" voice coil. The cabinet is constructed from birch plywood with a polyurea finish, offering high strength due to its internal wood and steel reinforcement structure. The two woofers, configured in a back-reflex system, provide a fast, powerful, and defined low-frequency response. An asymmetrical crossover ensures that only the upper woofer reproduces the vocal range, preventing mid-range interference. The coaxial coupling of the high-frequency driver results in a coherent and transparent overall response with linear 70° horizontal and 50° vertical dispersion. The Class-D amplifier utilizes two high-efficiency channels, delivering a total of 2400W RMS, enabling the speaker to produce 141dB SPL with a frequency response from 55 Hz to 18 kHz.

The WIND PRO series comprises four amplified loudspeakers (WIND PRO 208A, 210A, 212A, 215A) designed for excellent SPL and frequency response, each featuring 2 woofers, one coaxial. The compact, elegant design boasts a birch plywood cabinet with polyurea finish and reinforced internal structure. Advanced M-Modelling technology eliminates internal interference for a sound reproduction consistent with the input signal. All WIND PRO speakers include 2 Dante ports for analog-to-digital connectivity, allowing multiple units on a network. Specific bracket systems and flybars are available for suspension. The M-Connect software by Montarbo allows easy network control of each loudspeaker, offering user-friendly customization for parameters, levels, and mute functions. It also supports selecting analog and digital inputs, network parameters, and monitoring device temperature.

The EARTH PRO series includes two amplified subwoofers designed for high SPL and frequency response, featuring a similar elegant design and construction to the WIND PRO series. The 6th order band-pass configured woofer provides a fast, powerful, and extended bass response. Like the WIND PRO series, EARTH PRO subwoofers also feature M-Modelling technology, Dante ports, and M-Connect software for network control.

Safety Instructions

Important Safety Instructions:

• The lighting flash with arrowhead symbol within an equilateral triangle alerts users to the presence of uninsulated dangerous voltage within the product, which may pose a risk of electric shock.
• The exclamation point within an equilateral triangle alerts users to important operating and maintenance instructions.
• Read this section carefully before operating the product to protect yourself and others and to avoid invalidating the warranty.
• This product is designed for sound reinforcement and recording systems. Use for other purposes is at the user's/installer's sole risk.
• The unit conforms to Class I insulation and must be connected to a grounded outlet.
• To avoid fire and/or electric shock:
• Do not expose to rain or moisture; avoid use near water.
• Do not allow liquids or objects to enter the product. If this occurs, disconnect from mains immediately and refer to qualified service.
• Never place burning candles or open flames on the device.
• Ensure the mains voltage matches the product's stated voltage.
• Connect only to a grounded mains outlet using the supplied power cable. Use an identical cable for replacement.
• Unplug from the mains socket before any maintenance.
• Do not place objects on the power cable; avoid tripping hazards.
• Ensure adequate airflow for cooling; do not obstruct air intake openings. Allow access to the mains power socket and connector.
• Replace fuses only with identical types and ratings.
• Remove all connections before moving the product.
• To disconnect, pull the plug, not the cable.
• Ensure the supporting surface is stable and can handle the product's weight and size. Use appropriate stands and ensure stability when stacking units.
• Install in a protected area inaccessible to unqualified personnel.
• Keep children and animals under close supervision, as the product can generate high acoustic pressures dangerous to hearing.
• Never expose children to high sound sources.

Caution: The product contains no user-serviceable parts. Do not disassemble or remove the rear panel to prevent fire or electric shock. Refer all servicing to authorized personnel.

Technical Specifications

Control and Connection Panel

The control and connection panel on the WIND PRO 215A includes the following:

• [1] Input: Balanced Line Input (XLR/Jack combo) with 20kΩ impedance.
• [2] Link/Mixed Output: Balanced XLR output for parallel connection of multiple systems.
• [3] POWER LED: Green LED indicating proper operation.
• [4] Ethercon Input: For Dante or M-Connect software connection.
• [5] Dante/M-Connect Sync LED: Green LED indicating proper sync.
• [6] Power Input: Powercon TRUE1 mains power input.
• [7] Power Output: Powercon TRUE1 mains power output.
• [8] Fuse Holder: For the mains fuse.
• [9] Cooling Fan: For heat dissipation.
• [10] GND/LIFT Button: For ground lift selection.
• [11] WiFi Button: Activates WiFi connection.
• [12] LIM/CLIP/THERMAL LED: Red LED indicating DSP engagement (Limiter, Clip, Thermal protection).
• [13] PRESET Button: Selects one of eight DSP presets (Full Range, Low Cut, Near Fill, Wall Mount, User 1-4).

Diagram of the Control and Connection Panel:

[Image description: A diagram showing the rear panel of the WIND PRO 215A with numbered connection points and controls.]

Usage and Reset Procedures

The Montarbo WIND PRO and EARTH PRO series are designed for easy connection and setup, maximizing product potential.

Connection to M-Connect Software:

1. Ensure M-Connect software is installed on your PC/MAC.
2. Create a network using a 1GBit certified router.
3. Use a CAT 5E/6 LAN cable to connect the router to one of the Ethercon ports on the loudspeaker.
4. Turn on the loudspeaker.
5. Run the M-Connect software and assign desired parameters.

Connection to DANTE Protocol:

1. Ensure Dante Controller software is installed on your PC/MAC and use an audio mixer with a Dante card.
2. Create a network using a 1GBit certified router.
3. Use a CAT 5E/6 LAN cable to connect the router to one of the Ethercon ports on the loudspeaker.
4. Turn on the loudspeaker.
5. Run the Dante Controller software and assign desired parameters.

WiFi Connection:

Press the WiFi button on the loudspeaker until it flashes, then release. Ensure a dedicated WiFi network is accessible.

Loudspeaker Hardware RESET:

1. Turn off the loudspeaker.
2. While holding the PRESET button, turn on the loudspeaker.
3. All LEDs will flash after 2 seconds.
4. Release the PRESET button, then quickly press it again (1 click).
5. All LEDs will turn off.
6. The PRESET 1 LED will light on again.

Spare Parts

The following spare parts are available for the WIND PRO 215A:

• B02215A: Screen-printed DSP panel
• D600005: Ampli PowerSoft Litemod 4HC
• D10WP15: Filter WindPro 215A
• A300A28: 15" Neodymium Coaxial loudspeaker with 1.4" driver
• A300A29: 15" Ferrite woofer
• D20WP215: Black protective grille for WindPro 215A
• A088678: Black "T" handle
• A088675: Black shell box
• B010023: Speaker stand adaptor

[Image description: An exploded view diagram of the WIND PRO 215A showing the location of various spare parts.]

Frequently Asked Questions (FAQ)

Accessories

The following accessories are available for the WIND PRO series:

• DOLLY EARTH PRO 115-118 - F030098
• FLYBAR EARTH PRO 115-118 - F030094
• BRACKET WIND PRO 208-210 BOTTON - F030095
• BRACKET WIND PRO 208-210 TOP - F030096
• FLYBAR WIND PRO 212-215 - F030093
• HORIZONTAL PLATE WIND PRO P212-215 - F030097
• VERTICAL PLATE WIND PRO 212 - F030091
• VERTICAL PLATE WIND PRO 215 - F030092
• CONNECTION KIT FLY EP - WP - F030100
• CONNECTION KIT FLY EP - EP - F030099

[Images of various accessories are displayed.]

Notes

[Blank section for user notes.]

Disposal Information

WEEE Directive: The crossed-out wheeled bin symbol indicates that this product is covered by the Waste from Electrical and Electronic Equipment Directive and must be collected separately.

For Private Users (EU): Return used equipment to designated collection facilities free of charge. Local retailers may also accept old products when purchasing similar new ones.

For Professional Users (EU): Contact your Montarbo dealer for take-back information. Small products may be accepted by local collection facilities.

Outside EU: Contact local authorities for correct disposal methods.

Switzerland: Used equipment can be returned free of charge to dealers, or to designated collection facilities.

General Disclaimer: Information in this manual has been carefully checked, but no responsibility is assumed for inaccuracies. Montarbo srl is not responsible for damages or incidents caused by the use or malfunction of the apparatus. Specifications are subject to change without notice.

Manufacturing Information: Made in Italy. Compliant with EU legislation.

Company Information: Elettronica Montarbo srl, Via O. Pigini 8 - Z.I. Aneto - 62010 Montelupone (MC) Italy. Phone: +39 0733 227 1, Fax: +39 0733 227 250. Website: MONTARBO.COM. Company under the control of EKO Music Group SpA.