IKEA MITTLED LED Spotlight

Important Safety Instructions

For indoor use only.

Regularly check the cord, the transformer, and all other parts for damage. Do not use the product if any part is damaged. Keep these instructions for future use.

CAUTION! The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes. Do not immerse in water.

Cleaning: Use a damp cloth, never a strong cleaning agent.

CAUTION To reduce the risk of fire, electric shock, or injury to persons: Use only insulated staples or plastic ties to secure cords. Route and secure cords so that they will not be pinched or damaged when the cabinet is pushed to the wall. Position the portable cabinet light with respect to the cabinet so the lamp replacement markings can be read during relamping. Not intended for recessed installation in ceilings, or soffits. The low-voltage portable cabinet light may be installed inside or under a kitchen cabinet or other built-in furniture when:

1. The low-voltage Class 2 power supply is located outside the cabinet and is not concealed; and
2. The line voltage power supply cord is not concealed or run through openings in the cabinet, walls, ceilings, or floors. This requirement does not apply to the wiring between the cabinet light and the power unit. The National Electric Code (NEC) does not permit cords to be concealed where damage to insulation may go unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits, or cabinets where it may be inaccessible for examination. Cords should be visually examined periodically and immediately replaced when any damage is noted.

ATTENTION: CAUTION: Injury to persons and damage to the lamp and/or the mounting surface may result if the lamp is pulled from the surface. To reduce the likelihood of such injury or damage, mount only on a surface that is mechanically sound.

Use only IKEA LED drivers suited for this product. The total wattage of the lamps connected to one LED driver must not exceed the maximum power stated on that LED driver and never more than 30W.

WARNING Deviation from the assembly instructions may result in a risk of fire or electric shock.

IMPORTANT! MISE EN GARDE Ne pas arracher le luminaire. Cela peut provoquer des blessures ou l'endommagement du luminaire ou du support auquel il est fixé. Pour des raisons de sécurité, fixer le luminaire à une surface solide et adaptée.

ATTENTION Tout écart par rapport aux instructions d'assemblage peut entraîner un risque d'incendie ou de choc électrique.

ADVERTENCIA Para reducir el peligro de incendio, descarga eléctrica o lesiones a personas: Usar sólo grapas aislantes o agarraderas de plástico para fijar los cables. Colocar y fijar los cables de modo que al empujar el armario contra la pared éste no los dañe o rompa. Coloca la lámpara desmontable del armario de tal forma que puedan leerse las instrucciones para la sustitución de bombillas de la lámpara. No ha sido diseñada para instalación empotrada en techos o falsos techos. La lámpara de armarios de bajo voltaje desmontable puede instalarse dentro o debajo de un armario de cocina u otros muebles integrados siempre y cuando:

1. La toma eléctrica de bajo voltaje clase 2 esté ubicada fuera del armario y no quede oculta; y
2. El cable de suministro no quede oculto ni se haga pasar a través de aberturas en el armario, paredes, techos o suelos. Este requisito no se aplica al cable entre la luz del armario y la batería. El National Electric Code (NEC) no permite que se escondan cables cuando hay riesgo de que no se adviertan los daños en el aislante eléctrico. Para prevenir el peligro de incendios, no hacer pasar cables por detrás de paredes, techos, falsos techos o armarios donde queden inaccesibles para su examen. Los cables deben examinarse periódicamente, y cuando se advierta cualquier daño, reemplazarse de inmediato.

¡ATENCIÓN! ¡ADVERTENCIA! No extaer la lámpara de la superficie de montaje. Esto puede ocasionar daños a las personas, a la lámpara y/o a la superficie de montaje. Para reducir el riesgo de daños, la lámpara sólo se debe montar en una superficie adecuada y resistente.

Utiliza únicamente drivers LED IKEA. La potencia eléctrica (en vatios) de las lámparas conectadas a un driver LED no debe sobrepasar nunca la potencia total indicada en dicho LED y nunca debe ser superior a 30W.

ADVERTENCIA No seguir las instrucciones de montaje puede resultar en incendio o descarga eléctrica.

Assembly Instructions

The following tools may be needed:

• Screwdriver
• Pencil
• Drill with 8 mm (5/16") drill bit

Parts included:

• 2x Screws
• 1x Screw cover
• 2x Mounting brackets
• 2x Cable clips

Steps:

1. Measure and mark the desired positions for the mounting brackets. Ensure the surface is mechanically sound.
2. Drill holes using an 8 mm (5/16") drill bit at the marked positions.
3. Attach the mounting brackets using the provided screws.
4. Connect the LED light to the mounting brackets. Ensure it clicks into place.
5. Secure the cables using the provided cable clips, ensuring they are not pinched or damaged.
6. Connect the LED light to the power supply and driver.

Note: LED driver and power supply cord are sold separately.

English: LED driver and power supply cord are sold separately.

Français: Driver LED et câble d'alimentation vendus séparément.

Español: El “driver” LED y el cable de alimentación se venden aparte.

The diagram shows how to connect multiple MITTLED lights to a single LED driver and power supply, illuminating different sections of a cabinet.