Service Parts List
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
The document displays an exploded view diagram of the M18™ Brushless Blower, illustrating the arrangement of various components.Numbered callouts correspond to specific parts listed in the tables below.An example note indicates: "Component Parts (Small #) Are Included When Ordering The Assembly (Large #)."
Parts List (Figure 1-26)
| FIG. | PART NO. | DESCRIPTION OF PART | NO. REQ. |
|---|---|---|---|
| 1 | 31-15-2581 | M4 x 16mm Pan Hd. Torx T-20 B Screw | (23) |
| 2 | Inlet Cover | (1) | |
| 3 | M3.5 x 7mm Pan Hd. Torx T-10 Screw | (2) | |
| 4 | Bell Tube | (1) | |
| 5 | M7 x 1 Lock Nut | (1) | |
| 6 | Washer | (1) | |
| 7 | Fan Dome | (1) | |
| 8 | Fan | (1) | |
| 15 | Stator | (1) | |
| 17 | Right Motor Cage | (1) | |
| 18 | Left Motor Cage | (1) | |
| 19 | M3 x 14mm Torx T-10 Screw | (4) | |
| 20 | Trigger | (1) | |
| 21 | G2 Blower Lock-On | (1) | |
| 22 | Sponge for Lock-On | (1) | |
| 23 | Handle Cover | (1) | |
| 24 | Handle Support | (1) | |
| 25 | PCBA | (1) | |
| 26 | Spring for Lock-On | (1) |
Parts List (Figure 27-46)
| FIG. | PART NO. | DESCRIPTION OF PART | NO. REQ. |
|---|---|---|---|
| 27 | Spring for Nozzle Lock | (1) | |
| 28 | Cone Section | (1) | |
| 29 | Nozzle Lock | (1) | |
| 30 | 31-01-5925 | Injection Molded Nozzle (Blower Tube) | (1) |
| 32 | 10-22-1739 | Warning Label | (1) |
| 33 | 10-22-1741 | Warning Label | (1) |
| 34 | 12-20-3352 | Service Nameplate | (1) |
| 40 | 31-01-0425 | Service Console without Nozzle Assembly | (1) |
| 46 | Rotor Assembly | (1) |
Notes
FIG. 32,33, 34 NOTES: A clean, dry surface is essential for proper performance for any adhesive system. The area intended for application of any adhesive label or nameplate must be prepared by cleaning with isopropyl alcohol. The solvent is to be applied with a clean, lint free applicator and the surface allowed to dry before applying any label or nameplate.
MILWAUKEE TOOL • www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Screw Sequence - Fastening Order
The document includes diagrams illustrating the screw fastening sequence for assembling the M18 Brushless Blower. These diagrams show different views of the tool with numbered callouts indicating the specific screws and their placement order during assembly.
Wiring Instructions
An internal view diagram shows the layout of electrical components including the PCB Board, Fuse, Micro Switch, Trigger, and Terminal Block, along with the wiring connections between them.
Screw Torque Specifications
| FIG. | PART NO. | DESCRIPTION OF FASTENER | WHERE USED | SEAT TORQUE (kgf-cm) | (lb-in) |
|---|---|---|---|---|---|
| 1 | M4 x 16mm Pan Hd. Torx T-20 B Screw | Inlet Grate | 9 ± 1 | 8 ± 0.8 | |
| 1 | M4 x 16mm Pan Hd. Torx T-20 B Screw | Handle Housing | 11 ± 1 | 10 ± 0.8 | |
| 1 | M4 x 16mm Pan Hd. Torx T-20 B Screw | Bell Tube to Handle Housing | 11 ± 1 | 10 ± 0.8 | |
| 1 | M4 x 16mm Pan Hd. Torx T-20 B Screw | Cone Section to Handle Housing | 11 ± 1 | 10 ± 0.8 | |
| 3 | M3.5 x 7mm Pan Hd. Torx T-10 Screw | Bell Tube to Motor Housing | 4.5 ± 1.5 | 4 ± 1.3 | |
| 5 | Nut | Fan | 18.5 ± 1.5 | 16 ± 1.3 | |
| 19 | M3 x 14mm Torx T-10 Screw | Left Motor Cage | 8 ± 1 | 7 ± 0.8 |
Wiring Instructions - Continued
This section provides detailed steps for routing wires within the tool.
- Make sure all the wires are in the main groove.
- Do not put wires through the rib spot in the yellow circle.
- Make sure the RED wire is on top of the other wires through the slim grooves. The BLACK wire (thick one) should be in the middle and the remaining wires should be below them.
- When routing the wires from the Terminal Block to the PCB Board, please make sure the wires fit securely inside the traps and between the ribs without pinching the wires.
WARNING:
- Take notice of wire routing and position in wire guides and traps while dismantling tool.
- Be sure that all components of the electronics kit are seated firmly and squarely in housing recesses.
- Avoid pinched wires; be sure all wires and sleeves are pressed completely down in wire guides and traps.
- Prior to installing housing cover onto handle support, be sure that there are no interferences.
- Be sure to check for functionality of switches and buttons after housing halves have been secured.
Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
