Technical Information
Input voltage range: 10-30V DC (12/24V system)
Input current max: 2A
Output power: 10W (9.1V, 1.1A)
Standby power draw: < 0.2W
Waterproof rating: IPX6 front and back
Certifications: Qi, CE, FCC, ROHS, UKCA, UNECE R10 E24, C-Tick, IC, PSE
For latest tech info visit: www.scanstrut.com/rokk-wireless
ℹ️ READ IMPORTANT SAFETY INFORMATION LEAFLET BEORE INSTALLING.
Installation Guide
Warning Check Scale: 50 mm / 2" scale provided for reference.
Drilling Template: Scale 1:1 template for drilling holes. Main hole Ø6mm (0.24"), pilot holes 3 x Ø2.5mm (3/32") to Ø3mm (1/8").
Part List:
- ROKK Wireless Edge x1
- No 6 x 1 1/4" (32mm) self tapping screw x3
- Bung (for wire feed hole)
Tools Required:
- 06mm (0.24") drill bit
- Drill bit (for pilot holes):
- Soft Material (E.g. plywood): No. 6 Screw, 2.5mm (3/32")
- Hard Material (E.g. Fiberglass, acrylic, hardwood): 3mm (1/8")
- Pozi screwdriver
Installation Steps:
Step 1: Select Mounting Location
Choose an optimal location for mounting the device.
Step 2: Check Viewing Angle and Adjustability
Verify the viewing angle, full jaw extension, and 90° adjustability of the mount.
Step 3: Prepare Drilling Template
Cut out the drill template, check its alignment, and stick it down to the chosen surface.
Step 4: Drill Holes
Drill the main Ø6mm (0.24") hole in the centre of the template. Drill 3 pilot holes as indicated (refer to tools required table for sizes).
Step 5: Prepare Hole and Mount
Lightly de-burr the 6mm (0.24") hole. Feed the wire through the hole. Apply sealant to the 3 pilot holes. Evenly screw the mount into place. Insert the bung into the wire feed hole.
Step 6: Connect Power
Connect the wires to a 12V or 24V DC supply, ensuring a waterproof connection. Fuse the connection according to the input voltage and current requirements.
User Guide & Care
User Guide: Place device centrally within the ROKK Wireless Edge jaws.
Care: Wash down carefully with fresh water.
Smart LED Light Guide
The LED indicator provides status information:
- Solid red: Product has power and is ready to charge.
- Solid green: Product is charging.
- Flashing red: Indicates an issue:
- Foreign object detection: A metallic object is placed on top that is not Qi compatible.
- Thermal cutout: Internal temperature is too high or too low. Wait for the product to return to its operating temperature.
- Flashing green/red: Input current is too low.
Visual representation of LED states:
- [Image: Phone placed centrally in jaws, LED is solid red.]
- [Image: Phone placed centrally in jaws, LED is solid green.]
- [Image: Phone placed centrally in jaws, LED is flashing red, indicating a fault.] ❌
- [Image: Phone placed centrally in jaws, LED is flashing green/red, indicating low input current.] ❌
Important Information & Warnings
In Extreme Usage Environments: Performance may vary.
Caution:
- The product is designed specifically for the charging of Qi compatible devices.
- The cable must be retained and not interfere with mechanical systems.
- This product contains no user serviceable components. Do NOT attempt to repair or alter the product in any way.
- The product will charge through non-metallic phone cases up to approximately 3mm thick. Phone cases may alter overall charge performance.
- When used in very high/low ambient temperatures or direct/prolonged sunlight, the product may temporarily shut down; this is a safety feature of the electronics.
- The IP rating is only valid if correctly installed as per these instructions and on a perfectly flat, non-porous, smooth surface.
- When selecting a mounting location, avoid places exposed to heat-radiating appliances and poorly ventilated areas.
EMC Installation Guidelines:
- Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations to ensure that electromagnetic interference between equipment is minimised.
- Correct installation is required to ensure that electromagnetic interference is kept to a minimum.
Wiring:
- This product is to be connected to a 12V DC or 24V DC battery power source only.
- The power supply must be switched off before installation.
- An appropriate fuse or circuit breaker must be used between the battery/power source and this product. Check for correct polarity of all wiring before switching the power on.
- This product may contain high voltages. Do not tamper with the product.
- This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (e.g., engine room).
- Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel, and all other hazardous objects.
- Ensure any holes cut will not significantly weaken the structure of the mounting surface.
- If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged.
- When extending the cable from the battery/power source to the product, ensure there is consistently a minimum of 10V being provided to the product. A wire gauge of 18AWG (0.82mm²) is recommended for any length of cable extension.
- The schematic in step 6 illustrates how the product should be connected to a 12V DC or 24V DC battery/power supply.
Environmental Protection:
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Important:
Scanstrut Ltd. accepts no responsibility for any injuries or other damages arising from the use of their products in any circumstances.
Warranty:
A 2-year, non-transferrable warranty covers this Scanstrut product only and not any devices that are mounted in it or on it. No warranty is given for users' devices, and users expose their devices to hazards, known or unknown, at their own risk.
