Scanstrut ROKK Wireless Sub Surface Charger

Technical Information

• Input Voltage Range: 10-30V DC (12/24V system)
• Input Current Max: 1.5A
• Output Power: 5W (5V, 1A)
• Standby Current Draw: < 0.03W
• Waterproof Rating: IPX6 front and back
• Certifications: Qi, CE, FCC, ROHS

Parts List

• ROKK Wireless Sub Surface x1
• Alcohol Wipe x1

Tools Required

• 64/65mm (2.5”) Hole Saw
• Power Drill

Installation Instructions

The product must be installed in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel/vehicle and/or product failure. Scanstrut recommends installation is carried out by a qualified electrician. No liability is accepted for damage and/or injury caused by incorrect installation.

1. Step 1: Drill a 64/65mm (2.5”) hole in the desired mounting surface.
2. Step 2: Remove the self-adhesive backing from the charger.
3. Step 3: Clean the mounting surface thoroughly with the provided alcohol wipe to ensure it is free from dirt or grease. Insert the charger into the drilled hole.
4. Step 4: Connect the wires to a 12/24V DC power supply, ensuring a waterproof connection. Fuse appropriately according to the input voltage and current.

Important Safety Information

WARNING

• This product is to be fitted to a 12V DC or 24V DC battery/power source only.
• The power supply must be switched off before installation.
• An appropriate fuse or circuit breaker must be used in-line between the battery/power source and the product.
• Check for correct polarity of all wiring before switching the power on.
• This product may contain high voltages. Do not tamper with the product.
• This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere e.g. engine rooms.
• Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel and all other hazardous objects.
• Ensure any holes cut will not significantly weaken the structure of the surface.
• If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged.
• The product cannot charge through a metallic surface.

CAUTION

• The product is specifically for the charging of Qi compatible devices.
• The cable must be retained and not interfere with mechanical systems.
• This product contains no user serviceable components. Do NOT attempt to repair or alter the product in any way.
• The high friction top surface does not ensure the device will not slip during extreme operating environments such as high acceleration and deceleration.
• If a phone case which is thicker than 3mm is used, the device may not charge.
• When used in a high ambient temperature/direct sunlight the product may temporarily shut down; this is a safety feature of the electronics.
• The IP rating is only valid if correctly installed using the instructions and on a perfectly flat non-porous smooth surface.
• When selecting a mounting location, avoid places exposed to heat-radiating appliances and poorly ventilated areas.

EMC Installation Guidelines

Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations, to ensure that electromagnetic interference between equipment is minimised.

Wiring

When extending the cable from your battery/power source to the product, ensure there is a minimum of 10V being provided to the product continuously. We recommend a wire gauge of 18AWG (0.82mm²) for any length of cable extension.

This schematic is to illustrate how the product should be connected to a 12V DC or 24V DC battery/power supply.

Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

FCC Compliance Information

FCC Warning Statement: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This device complies with part 18 of the FCC Rules.

Information to the user:

• The device has potential interference, but the interference is very small and meets the requirements of the FCC rule.
• Equipment system maintenance is simple; please refer to the manual.
• The user can take simple measures to correct the interference, such as staying away from interference sources or turning off interference sources.