ASSEMBLY INSTRUCTION

STEP 1:

Prepare the Top Panel (A).

Insert Cam Bolts (1) and Wooden Dowels (3) into the pre-drilled holes on the Top Panel (A). This step is performed twice (x2).

Diagram Description: Shows Part A (Top Panel) with arrows indicating where to insert Cam Bolts (1) and Wooden Dowels (3). An inset provides a magnified view of the hardware being fitted. A 'x2' symbol indicates the action is repeated.

Hardware Used:

• Cam Bolt (1): 2 pcs
• Wooden Dowel (3): 2 pcs

STEP 2:

Attach the Middle Panel (E) to the Top Panel (A).

Align the Middle Panel (E) with the Top Panel (A). Insert Cam Locks (2) into the corresponding holes on Panel E and tighten them using the Allen Key (9) to secure Panel E to Panel A. This step is performed twice (x2).

Diagram Description: Shows Part A (Top Panel) with Part E (Middle Panel) being attached. Arrows indicate alignment. Insets show Cam Locks (2) being inserted and tightened with Allen Key (9). A 'x2' symbol indicates the action is repeated.

Hardware Used:

• Cam Lock (2): 2 pcs
• Allen Key (9): 1 pc

STEP 3:

Attach Side Panels (C, D) to the assembly.

Insert Wooden Dowels (3) into the Side Panels (C, D). Align the Side Panels with the Top Panel (A) and Middle Panel (E). Secure them using Short Bolts (4) with Flat Washers (6) and Lock Washers (7), tightened with the Allen Key (9). This step is performed twice (x2).

Diagram Description: Shows the partially assembled unit with Side Panels (C and D) being attached. Arrows indicate alignment. Insets show Wooden Dowels (3) inserted into side panels, and Short Bolts (4) with washers (6, 7) being secured by Allen Key (9). A 'x2' symbol indicates the action is repeated.

Hardware Used:

• Wooden Dowel (3): 3 pcs (per side)
• Short Bolt (4): 2 pcs (per side)
• Flat Washer (6): 2 pcs (per side)
• Lock Washer (7): 2 pcs (per side)
• Allen Key (9): 1 pc (for the step)

STEP 4:

Attach the Back Panel (F).

Insert Wooden Dowels (3) into the designated holes on the back edges of the Side Panels (C, D) and Middle Panel (E). Slide the Back Panel (F) into place, aligning it with the dowels. Secure the Back Panel using T Nuts (8) inserted into the corresponding holes, tightened with the Allen Key (9). This step is performed twice (x2).

Diagram Description: Shows the partially assembled unit with the Back Panel (F) being attached. Arrows indicate sliding motion. Insets show Wooden Dowels (3) being inserted and T Nuts (8) being secured with Allen Key (9). A 'x2' symbol indicates the action is repeated.

Hardware Used:

• Wooden Dowel (3): 4 pcs
• T Nut (8): 2 pcs

STEP 5:

Attach the Bottom Panel (B).

Insert Wooden Dowels (3) into the Bottom Panel (B). Align the Bottom Panel (B) with the Side Panels (C, D) and Middle Panel (E). Secure it using Short Bolts (4) with Flat Washers (6) and Lock Washers (7), and Long Bolts (5) with Flat Washers (6) and Lock Washers (7), tightened with the Allen Key (9). This step is performed twice (x2).

Diagram Description: Shows the unit from the bottom, with the Bottom Panel (B) being attached. Arrows indicate alignment. Insets show Wooden Dowels (3) inserted, and Short Bolts (4) and Long Bolts (5) with washers (6, 7) being secured by Allen Key (9). A 'x2' symbol indicates the action is repeated.

Hardware Used:

• Wooden Dowel (3): 5 pcs
• Short Bolt (4): 2 pcs
• Long Bolt (5): 2 pcs
• Flat Washer (6): 4 pcs
• Lock Washer (7): 4 pcs
• Allen Key (9): 1 pc

STEP 6:

Prepare the Doors (H).

Attach Slide Guides (11) to the top and bottom edges of the Door (H). Attach Metal Spindle Locks (12) to the corresponding positions on the Door (H). This is done for all four slide guide locations (x4).

Diagram Description: Shows the Door component (H). Insets show Slide Guides (11) being attached to the edges and Metal Spindle Locks (12) being attached to specific points. A 'x4' symbol indicates the action is repeated.

Hardware Used:

• Slide Guide (11): 4 pcs
• Metal Spindle Lock (12): 4 pcs

STEP 7:

Insert the Doors (H) into the bench frame.

Carefully slide the assembled doors (H) into the vertical channels on the front of the bench frame. The slide guides should engage with the internal rails.

Diagram Description: Shows the bench frame and the Door assembly (H) being slid into place from the front. Arrows indicate the direction of insertion.

STEP 8:

Attach the Left Side Panel (D) to the frame.

Align the Left Side Panel (D) with the front and back edges of the bench. Secure it using Long Bolts (5) with Flat Washers (6) and Lock Washers (7), tightened with the Allen Key (9). This step is performed four times (x4).

Diagram Description: Shows the bench frame with the Left Side Panel (D) being attached to the front and back. Insets show Long Bolts (5) with washers (6, 7) being secured by Allen Key (9). A 'x4' symbol indicates the action is repeated.

Hardware Used:

• Long Bolt (5): 4 pcs
• Flat Washer (6): 4 pcs
• Lock Washer (7): 4 pcs
• Allen Key (9): 1 pc

STEP 9:

Install the Shelf (G).

Insert Support Pins (10) into the desired pre-drilled holes inside the bench compartments (left or right). Place the Shelf (G) onto the Support Pins. This process is the same for either compartment. This step uses four support pins (x4).

Diagram Description: Shows the bench with internal compartments. Arrows indicate inserting Support Pins (10) into holes. The Shelf (G) is shown being placed onto the pins. Two possible configurations (left or right compartment) are illustrated. A 'x4' symbol indicates the action is repeated.

Hardware Used:

• Support Pin (10): 4 pcs

STEP 10:

Place the Cushion (J).

Position the Cushion (J) on top of the assembled bench.

Diagram Description: Shows the assembled bench and the Cushion (J) being placed on top. A 'Finished' label indicates the final product.

Part Used:

• Cushion (J): 1 pc