Shelly Wave Pro Shutter: User and Safety Guide
DIN-mountable Z-Wave® shutter control with power measurement.
Read Before Use
This document contains important technical and safety information about the Device, its safe use and installation. Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the Device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or improper operation of this Device due to failure of following the user and safety instructions in this guide.
About the Device
The Device is a DIN rail mountable unit that enables remote control of motorized blinds, roller shutters, venetian blinds, awnings, etc. It measures the power consumption of the connected device. It is recommended to use only motors with electronic or mechanical limit switches. The motor limit switches must be set correctly before connecting the Device to the motor.
Diagram Description (Fig. 1): The device shows terminal connections. Key terminals include: N ([Neutral]), L ([Live]), SW1 ([Switch UP]), SW2 ([Switch DOWN]), I1 ([Motor Input UP]), I2 ([Motor Input DOWN]), O1 ([Motor Output UP]), O2 ([Motor Output DOWN]). It also features an 'S' ([S Button]) and indicates connections for a motor ([Motor]).
Diagram Description (Fig. 2): This diagram illustrates a typical wiring setup. It shows connections for L ([Live]), N ([Neutral]), SW1 ([Switch UP]), SW2 ([Switch DOWN]), I1 ([Motor Input UP]), I2 ([Motor Input DOWN]), O1 ([Motor Output UP]), O2 ([Motor Output DOWN]), and the motor ([Motor]). It also depicts the placement of RC snubbers parallel to the motor connections for inductive loads.
Safety Precautions and Warnings
- WARNING! Risk of electric shock. Ensure that after installing the device, its screw terminals are not accessible to users.
- WARNING! The operation of the service button must be managed by a professional installer. Risk of electric shock.
- CAUTION! Danger of electrocution. Mounting/installation of the Device to the power grid must be performed with caution by a qualified electrician.
- WARNING! Danger of electrocution. Every change in the connections must be done after ensuring there is no voltage present at the Device terminals.
- CAUTION! Use the Device only with a power grid and appliances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage it.
- CAUTION! Do not connect the Device to appliances exceeding the given max load.
- CAUTION! Do not shorten the antenna.
- RECOMMENDATION: Place the antenna as far as possible from metal elements as they can cause signal interference.
- CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
- CAUTION! Do not install the Device where it can get wet.
- CAUTION! Do not use the Device if it has been damaged.
- CAUTION! Do not attempt to service or repair the Device yourself.
- RECOMMENDATION: Connect the Device using solid single-core wires with increased insulation heat resistance not less than PVC T105°C (221°F).
- CAUTION! Before starting the mounting/installation of the Device, check that the breakers are turned off and there is no voltage on their terminals. This can be done with a phase tester or multimeter. When you are sure that there is no voltage, you can proceed to connecting the wires.
- CAUTION! Allow at least 10 mm of space around each Pro device if you expect currents higher than 5 A per channel.
- CAUTION! Use only one phase AC circuit. Do not use mixed AC and DC circuits.
- CAUTION! Do not allow children to play with the push-buttons/switches connected to the Device. Keep the devices for remote control of Shelly Wave (mobile phones, tablets, PCs) away from children.
- RECOMMENDATION: For inductive appliances that cause voltage spikes during switching on/off, such as electrical motors, fans, vacuum cleaners and similar ones, an RC snubber (0.1 μF / 100 Ω / 1/2 W / 600 VAC) should be connected parallel to the appliance.
Technical Specifications
| Parameter | Value |
|---|---|
| Power supply | 120 V AC, 50/60 Hz |
| Power consumption | < 0.3 W |
| Max. switching voltage AC | 120 V |
| Max switching current AC | 12.5 A per channel |
| Power measurement (W) | Yes |
| Overheating protection | Yes |
| Overcurrent protection | Yes |
| Overvoltage protection | Yes |
| Wireless protocol | Z-Wave |
| CPU | S800 |
| Z-Wave® Mesh distance | Up to 40 m indoors (131 ft.) (depends on local condition) |
| Z-Wave® Mesh frequency band | 908.4 MHz |
| Z-Wave® Long range distance | Up to 80 m indoors (262 ft.) or up to 1000 m outdoors (3281 ft.) |
| Z-Wave® Long range frequency band | 912 MHz |
| Z-Wave® repeater | No (Long Range), Yes (Mesh) |
| Size (H x W x D) | 94x19x69 ±0.5 mm / 3.70x0.75x2.71 ±0.02 in |
| Weight | 75 g / 2.65 oz. |
| Mounting | DIN rail |
| Screw terminals max. torque | 0.4 Nm / 3.54 lbin |
| Conductor cross section | 0.5 to 2.5 mm² / 20 to 14 AWG (green connector), 0.5 to 1.5 mm² / 20 to 16 AWG (white connectors) |
| Conductor stripped length | 6 to 7 mm / 0.24 to 0.28 in (green connector), 5 to 6 mm / 0.20 to 0.24 in (white connectors) |
| Shell material | Plastic |
| Color | Black |
| Ambient temperature | -20°C to 40°C / -5°F to 105°F |
| Humidity | 30% to 70% RH |
| Max. altitude | 2000 m / 6562 ft. |
FCC Notes
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification or change to this equipment. Such modifications or changes could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Manufacturer Information
Manufacturer: Shelly Europe Ltd.
Address: Shelly Europe ltd, 51 Cherni Vrah Blvd., building 3, floor 2 and 3, Lozenetz Region, Sofia 1407, Republic of Bulgaria
Tel.: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Changes in the contact data are published by the Manufacturer at the official website: https://www.shelly.com
Disposal & Recycling
This refers to the waste of electrical and electronic equipment. It is applicable in the US and other countries to collect waste separately. This symbol on the product or in the accompanying literature indicates that the product should not be disposed of in the daily waste. Shelly Wave Pro Shutter must be recycled to avoid possible damage to the environment or human health from uncontrolled waste disposal and to promote the reuse of materials and resources. It is your responsibility to dispose of the device separately from general household waste when it is already unusable.
Additional Information
Ordering Code: QUSH-0A1P10US
FCC ID: 2BDC6-WAVEPROSHUTTER
For more detailed installation instructions, visit: https://shelly.link/ShellyWaveProShutterUS_LR-KB
Shelly Wave devices
Support
Shelly Europe
