Shelly Wave Pro 2PM: User and Safety Guide
2-circuit DIN-mountable Z-Wave® smart switch with power measurement
About Shelly Qubino
Shelly Qubino offers microprocessor-managed devices for remote control of electric circuits via smartphone, tablet, PC, or home automation systems. These devices operate on the Z-Wave® wireless communication protocol, requiring a gateway for configuration. When the gateway is internet-connected, Shelly Qubino devices can be controlled remotely. They are compatible with other Z-Wave® certified devices, and mains-operated nodes act as repeaters to enhance network reliability.
Wave Pro Series
The Wave Pro series is designed for homes, offices, retail stores, and manufacturing facilities. These devices are DIN-mountable within breaker boxes, making them ideal for new construction. All Wave Pro devices can be controlled and monitored through a Z-Wave® network.
About the Device
The Shelly Wave Pro 2PM is a DIN rail mountable 2-channel smart switch with power measurement. It controls the on/off function for two independent electrical devices, supporting a load of up to 16 A per channel (25 A total). It is compatible with both switches and push-buttons.
Installation Instructions
The Device can be DIN-mounted inside a breaker box. Refer to the wiring scheme (Fig. 1) for installation details.
CAUTION! Danger of electrocution. Installation must be performed by a qualified electrician. Ensure no voltage is present at the terminals before making any changes. Use only with power grids and appliances that comply with applicable regulations. Do not connect appliances exceeding the maximum load. Allow at least 10 mm of space around the device for currents over 5 A per channel. Connect the device only as shown in the instructions. Do not install where it can get wet. Do not use if damaged. Do not attempt self-repair. Ensure breakers are off and terminals have no voltage before installation. Do not shorten the antenna. For optimal signal, place the antenna away from metal elements. Use solid single-core or stranded cables with ferrules, with insulation heat resistance of at least T105°C (221°F). For inductive appliances, an RC snubber (0.1 μF / 100 Ω / 1/2 W / 600 V AC) should be connected in parallel.
CAUTION! Keep devices for remote control away from children. Do not allow children to play with connected switches/push-buttons.
Connect the load to terminals 01 and 02, and the Neutral wire. Connect the Live wire to terminal 'i'. Connect the Live wire to the Device L terminal and the Neutral wire to the N terminal. Connect switches or push-buttons to SW1 and SW2 terminals and the Live wire.
Operational Instructions
SW1: If configured as a switch (default), toggling the switch changes the state of output 0 (01). If configured as a push-button, each press changes the state of output 0 (01).
SW2: If configured as a switch (default), toggling the switch changes the state of output 02. If configured as a push-button, each press changes the state of output 02.
Supported Load Types
- Resistive (incandescent bulbs, heating devices)
- Inductive with RC Snubber (LED light drivers, transformers, fans, refrigerators, air-conditioners)
- Capacitive (capacitor banks, electronic equipment, motor start capacitors)
Extended User Guide
For more detailed installation instructions, use cases, and comprehensive guidance on Z-Wave® network functions, refer to the extended user guide at: https://shelly.link/WavePro2PM-KB-US
Specifications
| Power supply | 110-240 V AC, 50/60 Hz |
| Power consumption | < 0.3 W |
| Max. switching voltage AC | 240 V |
| Max. switching current AC | 16 A per channel, 25 A total |
| Overheating protection | Yes |
| Overload protection | Yes |
| Overvoltage protection | Yes |
| Power measurement (W) | Yes |
| Distance | Up to 40 m indoors (131 ft.) |
| Z-Wave® repeater | Yes |
| Z-Wave® frequency bands | 908.42MHz, 912MHz, 920MHz |
| Size (H x W x D) | 94x19x69 ±0.5 mm / 3.70x0.75x2.71 ±0.02 in |
| Weight | 75 g/2.65 oz. |
| Mounting | DIN rail |
| Screw terminals max. torque | 0.4 Nm/3.54 lbin |
| Conductor cross section | 0.5 to 2.5 mm² / 20 to 14 AWG (green connector) 0.5 to 1.5 mm² / 20 to 16 AWG (white connectors) |
| Conductor stripped length | 6 to 7 mm/ 0.24 to 0.28 in (green connector) 5 to 6 mm/ 0.20 to 0.24 in (white connectors) |
| Shell material | Plastic |
| Color | Black |
| Ambient temperature | -20°C to 40°C / -5°F to 105°F |
| Humidity | 30% to 70% RH |
| Max. altitude | 2000 m/6562 ft. |
Important Disclaimer
Z-Wave® wireless communication may not always be 100% reliable. This Device should not be used in situations where life and/or valuables are solely dependent on its functioning. If the Device is not recognized by your gateway or appears incorrectly, you may need to change the Device type manually and ensure your gateway supports Z-Wave Plus® multi-channel devices.
Disposal & Recycling
This product is subject to waste electrical and electronic equipment regulations. It should not be disposed of with regular household waste. Please recycle to prevent environmental damage and promote resource reuse. Dispose of the device separately from general household waste when it is no longer usable.
FCC Notes
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for radio or TV interference caused by unauthorized modifications. This equipment complies with FCC radiation exposure limits for an uncontrolled environment and can be used in portable exposure conditions without restriction.
Manufacturer
Shelly Europe Ltd.
Address: 51 Cherni Vrah Blvd., building 3, floor 2 and 3, Lozenetz Region, Sofia 1407, Republic of Bulgaria
Tel.: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Web: https://www.shelly.com
Ordering Code: QPSW-0A2P16US
Wave Pro 2PM (US)
Support
Shelly Europe
