Shelly RGBW 2 Smart WiFi LED Controller User Guide

LEGEND

• DC: 12/24V DC power supply
• GND: 12/24V DC power supply
• R: Red light control
• G: Green light control
• B: Blue light control
• W: White light control
• 1: Switch input (AC or DC) for on/off/dimming

Specification

The Shelly RGBW2 WiFi LED Controller by Allterco Robotics is designed for direct installation to LED strips/lights to control color and dimming. It can function as a standalone device or with a home automation controller.

• Power supply: 12 or 24V DC
• Power output (12V): 144W (combined), 75W (per channel)
• Power output (24V): 288W (combined), 150W (per channel)
• Complies with EU standards: RE Directive 2014/53/EU, LVD 2014/35/EU, EMC 2004/108/WE, RoHS2 2011/65/UE
• Working temperature: -20°C to 40°C
• Radio signal power: 1mW
• Radio protocol: WiFi 802.11b/g/n
• Frequency: 2400-2500 MHz
• Operational range: up to 20 m outdoors, up to 10 m indoors (depending on construction)
• Dimensions (HxWxL): 43 x 38 x 14 mm
• Electrical consumption: < 1 W

Technical Information

Control via WiFi from a mobile phone, PC, automation system, or any device supporting HTTP and/or UDP protocol. Features microprocessor management. Controlled elements include multiple white and color (RGB) LED diodes. Shelly can be controlled by an external button/switch.

CAUTION! Danger of electrocution. Mounting the Device to the power grid must be performed with caution.

CAUTION! Do not allow children to play with the switch connected to the Device. Keep remote control devices (mobile phones, tablets, PCs) away from children.

Introduction to Shelly®

Shelly is a family of innovative devices for remote control of electrical appliances via mobile phone, PC, or home automation system. Shelly uses WiFi for connectivity and can operate within the same network, via remote access (Internet), standalone, or through a cloud service.

Shelly has an integrated web server for adjustment, control, and monitoring. It supports WiFi Access Point (AP) and Client Mode (CM). For Client Mode, a WiFi router must be within range. Shelly devices can communicate directly via HTTP protocol. An API is available from the manufacturer. Remote control is possible via the Shelly Cloud service.

Users can register and access Shelly Cloud via Android/iOS mobile applications or a web browser at https://my.Shelly.cloud/.

Installation Instructions

CAUTION! Danger of electrocution. Installation should be done by a qualified person (electrician).

CAUTION! Even when the Device is off, voltage may be present. Always disconnect power before making connection changes.

CAUTION! Do not connect the Device to appliances exceeding the maximum load.

CAUTION! Connect the Device only as shown in the instructions. Other methods may cause damage or injury.

CAUTION! Read all accompanying documentation carefully before installation. Failure to follow procedures may lead to malfunction, danger, or legal violations. Allterco Robotics is not responsible for loss or damage due to incorrect installation or operation.

CAUTION! Use the Device only with power grids and appliances complying with all applicable regulations. Short circuits may damage the Device.

RECOMMENDATION: Connect and control electric circuits and appliances only if they comply with respective standards and safety norms.

Initial Inclusion

Ensure the power grid is off before installation. Connect Shelly following the wiring scheme (fig. 1). You can use Shelly with the Shelly Cloud mobile application or the embedded web interface.

Control your home with your voice: All Shelly devices are compatible with Amazon Echo and Google Home. See guides at https://shelly.cloud/compatibility/Alexa and https://shelly.cloud/compatibility/Assistant.

Shelly Cloud Mobile Application

Download the Shelly Cloud app from the Google Play (Android - fig. 2) or App Store (iOS - fig. 3).

Shelly Cloud allows remote control and adjustment of Shelly devices worldwide with an internet connection.

Registration: Create an account to manage all Shelly devices. Use the email address for password recovery.

Forgotten Password: Enter your registered email address for password change instructions.

WARNING: Ensure correct email entry during registration for password recovery.

After registration, create rooms to organize your Shelly devices.

Shelly Cloud enables creating scenes for automatic device control based on time or other parameters (e.g., temperature, humidity, light).

Device Inclusion

Install the device according to instructions and power it on. Shelly will create its own WiFi Access Point (AP).

WARNING: If the WiFi network (SSID like shellyrgbw2-35FA58) is not created, check the connection. Reset the device if necessary: power off/on, then press the switch connected to DC (SW) 5 times within 20 seconds, or press the reset button once. The LED strip will flash. Power cycle again. Contact support@Shelly.cloud if issues persist.

Step 1: After powering on, Shelly creates its WiFi AP.

Step 2: Connect your phone, tablet, or PC to the Shelly WiFi network (e.g., shellyrgbw2-35FA58).

Step 3: Open a browser and navigate to 192.168.33.1 to access the Shelly web interface.

For iOS users: Minimize the app, go to Settings > WiFi, and connect to the Shelly network. Reopen the app.

For Android users: The app automatically scans and includes new Shelly devices on the WiFi network.

Step 4: Upon successful inclusion, a confirmation message appears. Device discovery can take up to a minute.

Step 5: In the Shelly Cloud app, select "Add Device" and choose the discovered device.

Step 6: Enter a Device Name, choose a Room, and optionally add an icon or picture. Press "Save Device".

Step 7: To enable remote control via Shelly Cloud, press "YES" on the "Connect to cloud" prompt.

Shelly Devices Settings

After inclusion, control and configure your Shelly device via the app. Use ON/OFF buttons to control power. Tap the device name to access details, edit appearance, and settings.

Work Modes

Shelly RGBW2 has two work modes: Color and White.

• Color Mode: Full color gamma selection, 4 predefined colors (Red, Green, Blue, Yellow), and a dimmer slider for brightness.
• White Mode: Four separate channels, each with On/Off button and a dimmer slider for brightness adjustment.

Edit Device

Edit Device Name, Device Room, and Device Picture. Press "Save Device" when done.

Timer

Manage power supply automatically:

• Auto OFF: Automatically shuts down after a predefined time (seconds). 0 cancels.
• Auto ON: Automatically turns on after a predefined time (seconds). 0 cancels.

Weekly Schedule

Requires Internet connection. Shelly can turn on/off automatically at predefined times. Multiple schedules are possible.

Sunrise/Sunset

Requires Internet connection. Shelly uses internet data for local sunrise/sunset times to automate on/off actions, with options for specified times before or after.

Internet/Security

• WiFi Mode - Client: Connects to an available WiFi network.
• WiFi Mode - Access Point: Configures Shelly to create its own WiFi AP.
• Cloud: Enable or disable connection to the Cloud service.
• Restrict Login: Secure the web interface with a username and password.

ATTENTION! Incorrect settings may prevent connection; reset the device if necessary.

WARNING: If the WiFi network is not created, check connections and reset the device as described previously.

The Embedded Web Interface

Shelly can be set and controlled via a browser and WiFi connection without the mobile app.

ABBREVIATIONS USED:

• Shelly-ID: Unique device name (e.g., 35FA58).
• SSID: WiFi network name created by the device (e.g., shellyrgbw2-35FA58).
• Access Point (AP): Device creates its own WiFi connection point.
• Client Mode (CM): Device connects to another WiFi network.

Initial Inclusion (Web Interface)

1. Install and power on Shelly. It will create its WiFi network (AP).
2. Connect your device (phone, tablet, PC) to the Shelly WiFi network.
3. Open a browser and go to 192.168.33.1.
4. The web interface displays current mode, state, brightness, power button, cloud connection, and time.

Settings (Web Interface)

• Power On Default Mode: Set default state (ON, OFF, Restore Last Mode) upon power restoration.
• Time Zone and Geo-location: Enable/disable automatic detection.
• Firmware Update: Update Shelly's firmware when new versions are available.
• Factory Reset: Restore device to factory default settings.
• Device Reboot: Restart the device.
• Device Information: View Device ID and IP address.
• Advanced - Developer Settings: Configure action execution via CoAP (CoIOT) or MQTT.
• Firmware Upgrade: Shows current firmware version and allows updates.

Environmental Protection

Dispose of the device and its accessories in designated recycling locations. Follow environmental protection instructions for proper disposal and material recycling.

Warranty Terms

The device has a 24-month warranty from the date of purchase. The manufacturer is Allterco Robotics EOOD. Claims should be addressed to the Seller. The warranty covers manufacturing defects but excludes damages from improper use, accidents, unauthorized repairs, or environmental factors. Refer to the user manual for proper usage and maintenance. Contact support@shelly.cloud for operational problems.

Manufacturer: Allterco Robotics EOOD

Address: Sofia, 1407, 103 Cherni vrah blvd.

Tel: +359 2 988 7435

E-mail: support@shelly.cloud

Website: http://www.Shelly.cloud

Declaration of Conformity is available at: https://Shelly.cloud/declaration-of-conformity/

Latest user guide available at: https://shelly.cloud/downloads/