Baby Trend Nursery Center

Parts List

• 1x Playard (fully assembled)
• 1x Mobile Lower Arm
• 1x Mattress
• 1x Mobile Arm Holder
• 1x Bassinet with metal support tubes
• 1x Mobile Upper Curved Arm
• 1x Travel / Storage Bag
• 1x Mobile Tri-shaped Arm
• 1x Diaper Stacker
• 3x Toy Animal

Important Instructions

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

Customer Service: If you experience any difficulty, contact Baby Trend Customer Service at 1-800-328-7363 (8:00 AM - 4:30 PM PST, Monday-Friday). Please have your model number and manufacturing date available.

(Note: Spanish and French versions of instructions and warnings are also included in the original document.)

Safety Warnings

General Warnings

• Failure to follow these warnings and instructions could result in serious injury or death.
• Always provide necessary supervision for your child's safety. NEVER leave a child unattended.
• Ensure all latches are secure before use.
• Strings can cause strangulation! Keep strings away from children's necks and never suspend them over the playard or attach them to toys.
• Discontinue use when the child can climb out or reaches 35 in. (890 mm) height or 30 lbs. (14 kgs) weight, whichever comes first.
• Remove bumper pads, large toys, and other objects that could serve as steps for climbing out when the child can pull to standing.
• NEVER place the product near a window where blind cords or drapes could strangle a child.
• To reduce the risk of SIDS, place healthy infants on their back to sleep, unless advised otherwise by a physician.
• NEVER use this product if any parts are loose, missing, broken, or torn. Contact customer service for replacement parts.
• NEVER leave a child in the product with sides lowered. Ensure sides are raised and locked.
• NEVER use plastic bags or film as mattress covers; they can cause suffocation.
• This product is not intended for commercial use.
• If using a sheet, use only the one provided or one specifically designed for the mattress.

Fall Hazard Warnings

• Do not use when the infant begins to push up on hands and knees, or has reached 25 in. (635 mm) height, 15 lbs. (6.8 kgs) weight, or 4 months old, whichever comes first.
• Always check that the bassinet is securely locked on the base/stand by pulling upwards.

Suffocation Hazard Warnings

• Infants can suffocate in gaps between a mattress and product sides, or on soft bedding.
• Never add extra mattresses, pillows, comforters, or padding. Use only the manufacturer-provided mattress.
• Never use a water mattress.
• Child can become entrapped and die if improvised netting or covers are placed on top of the playard.

Assembly Instructions

Playard Assembly

General Notes:

• Adult assembly is required.
• Ensure all parts are present and undamaged before assembly.
• The playard must be fully assembled and securely locked before installing or using other accessories.

1. Step 1: Unzip the storage bag and remove the playard frame. Undo the fasten straps and set the mattress aside. Do NOT push the center down yet. (Figure 1 illustrates removing the frame.)
2. Step 2: Erect the top rails. Pull up one rail at a time, holding both sides, until the tubes latch securely. Ensure all rails are rigid. The center handle must remain raised for rails to lock. If a rail does not lock, ensure the center handle is fully raised and try again. (Figure 2 illustrates erecting the rails.)
3. Step 3: Once all four top rails are locked, push down on the center handle to automatically lock the mechanism. Test each top rail by pushing down slightly to confirm it is rigid and secure. (Figure 3a shows pushing the handle, Figure 3b shows a secure rail.)
4. Step 4: Place the mattress on the playard floor with the padded side facing up. (Figure 4 shows mattress placement.)
5. Step 5: Insert the hook and loop fasteners on the underside of the mattress through the slots in the playard floor. Fasten the straps to prevent the mattress from moving. (Figure 5a shows inserting fasteners, Figure 5b shows fastened straps.)
6. Step 6: To operate the brakes on the wheels, press downward on the brake levers. To release, lift upward on the lever. (Figure 6 illustrates brake operation.)

Folding the Playard

1. Step 7: Release the hook and loop fasteners holding the mattress. Do not unlock top rails yet; the center of the floor must be raised first. Rotate the center handle 90 degrees counter-clockwise and raise it as high as the top rails. Gather the legs and wheels towards the center. (Figure 7 illustrates rotating the handle.)
2. Step 8: Locate the rail latch release in the center and bottom of each rail. Squeeze the lever with two hands until the rail releases the tubes, then push down. If rails do not release completely, lift the center of the floor higher. Both tubes must release for the top rail to fold. (Figure 8a shows locating the release, Figure 8b shows pushing down.)
3. Step 9: Gather the four corners and center them tightly. Wrap the mattress around the playard frame with the padded side facing inward. (Figure 9 illustrates gathering corners.)
4. Step 10: Secure the mattress straps by feeding them through loops and folding them back. Place the folded playard into the carry bag, ensuring the handle protrudes from the zipper opening. (Figure 10 illustrates securing straps.)

Bassinet Assembly

Note: Playard must be fully assembled and locked before installing the bassinet feature. Remove the playard mattress to use inside the bassinet.

1. Step 11: Connect the opposing mattress support tubes attached to the bottom of the bassinet. Ensure tubes are connected as shown in Figure 11a and 11b.
2. Step 12: Position the bassinet over the playard and push down firmly on each plastic support clip until all are snapped into place. (Figure 12 illustrates securing the bassinet.)
3. Step 13: Place the playard mattress into the bassinet with the padded side facing upward. Fasten the tabs underneath the mattress to secure it. (Figure 13 illustrates mattress placement in the bassinet.)

To Remove Bassinet: Remove mattress, disconnect support tubes, unsnap clips, and lift bassinet.

Diaper Stacker Assembly

1. Step 14: Connect the diaper stacker to the playard by sliding the two connecting clips over an open portion of the top rail. Ensure clips attach easily without interfering with other features. (Figure 14 illustrates diaper stacker attachment.)

Mobile Assembly

Note: The mobile is for visual stimulation only and should be removed when the baby can push up on hands and knees. Mount on wall or ceiling if designed for it, out of reach. Always attach fasteners securely. Do NOT add extra strings or attach the mobile while the child is in the playard or bassinet.

1. Step 15: Insert the Mobile Lower Arm (a) into the Mobile Arm Holder (b) until they lock together. (Figure 15 shows this connection.)
2. Step 16: Insert the Mobile Upper Curved Arm (c) into the assembled Lower Arm (a, b) until locked. (Figure 16 shows this connection.)
3. Step 17: Snap the Mobile Tri-shaped Arm (d) onto the end of the Upper Curved Arm (a, b, c). Connect each of the three Toys (e) to the mobile by threading the string into the slot at the end of each arm. (Figure 17 illustrates attaching arms and toys.)
4. Step 18: Insert the bottom of the mobile arm into the frame of the playard. (Figure 18 shows final insertion.)

Maintenance and Cleaning

• Use only household mild soap and warm water.
• DO NOT USE BLEACH.
• DO NOT MACHINE WASH.