Baby Trend Nursery Center Mini Playard
Model #: PY90973
Instruction Manual
Parts List
Before assembling the playard, check that you have all the below parts for this model.
Nursery Center Components:
- Playard (fully assembled) x 1
- Mattress x 1
- Changing Table x 1
- Long Curved Bar x 2
- Short Bar with Connector Knob x 2
- Music Center x 1
- Travel / Storage Bag x 1
Close N Cozy (Type C) Components:
- Soft Goods x 1
- Strap Set x 1
- Mattress Support Bar x 2
- Lower Bar x 2
- Center Cross Bar x 1
- Upper Back Bar x 1
- Upper frame x 2
- Side frame x 2
- Leg x 4
- Screw x 4
This unit is not equipped with basket, bassinet, mobile, parent organizer, and canopy.
Important Instructions & Warnings
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
Item #: PY90973
Assembly requires adult supervision.
⚠️ WARNING:
- NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll into space between pad and loose mesh side causing suffocation.
- Infants can suffocate:
- In gaps between a mattress too small or too thick and product sides
- On soft bedding
- See playard floor and side rails for warnings.
- Failure to follow these warnings and the instructions could result in serious injury or death.
- NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair or instructions. NEVER substitute parts.
- NEVER leave child in product with sides lowered. Be sure sides are in raised and locked position whenever child is in product.
- NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation.
- This product is not intended for commercial use.
Important Safety Guidelines:
- The playard, including side rails, must be fully erected prior to use. Make sure latches are secure.
- Strings can cause strangulation! NEVER place items with a string around a child's neck such as hood strings or pacifier cords. NEVER suspend strings over playard or attach strings to toys.
- Discontinue use of the product when child is able to climb out or has reached the height of 35 in. (890 mm) or weight of 30 lbs. (14 kgs), whichever comes first.
- When child is able to pull to standing position, remove bumper pads, large toys and other objects that could serve as steps for climbing out.
- NEVER place product near a window where cords from blinds or drapes can strangle a child.
- Always provide the supervision necessary for the continued safety of your child. When used for playing, NEVER leave child unattended.
- To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.
Assembly Instructions
To Assemble Playard
Playard must be fully assembled and securely locked before installing or using other accessories.
- Unzip bag and remove Playard frame. Undo the three (3) fasten straps and set the mattress aside.
- Turn the Playard right side up, keeping legs and wheels close together. Stretch out the top of the Playard and pull up one side at a time of each top rail until each latch "Clicks" and locks securely into place. Note: The best way to lock the rail(s) is to hold one hand on each side and pull up sharply. Do not pull from the middle where the latch release is located.
- IMPORTANT: The handle located in the center of the Playard floor MUST remain raised (approx. 45.7 cm or 18 inches) while locking the side rails. If the center is not raised, the rails will NOT lock.
- To operate the brakes on the wheels, press downward on the brake levers. To release, lift upward on the lever.
- Once all four (4) top rails are locked, push down on the center handle. The center mechanism will rotate clockwise 90 degrees and automatically lock.
- IMPORTANT: Test each top rail by pushing down slightly to confirm it is rigid and locked securely before use.
- Place the Mattress on the floor of the Playard with the padded side facing up.
- Feed the three (3) hook and loop straps located on the underside of the Mattress through the slots in the floor of each end of the Playard. Fasten the hook and loop straps to the underside of the Playard floor to prevent the Mattress from moving.
If you experience difficulty and one side of the rail will lock but the other side will not, unlock the rail by squeezing the release in the center and try again. If you still have difficulty, contact Customer Service at 1-800-328-7363 or visit www.babytrend.com.
To use as a bassinet, skip to page 8 for bassinet installation instructions.
Folding Playard
- Undo the three (3) hook and loop straps holding the Mattress from underneath the Playard floor or remove the Mattress for the Bassinet and set aside.
- Grasp the center handle, push down, and rotate the handle counter-clockwise 90 degrees. Lift upward until the handle is as high as the top rails. Gather the Legs and Wheels together towards the center as close as possible so they nearly touch. Note: The top rails of the Playard are still in the "Locked" position.
- Locate the rail release lever in the center and bottom side of each rail. Lift slightly while squeezing the lever until the rail "Clicks" and releases. Push down each side of the rail while still holding the release lever until both sides are down. Repeat for all remaining sides. Note: If the top rail(s) do not release completely, DO NOT FORCE! Check the floor of the Playard to make sure all bottom rails are unlocked and the middle handle is pulled up. If so, repeat step #3.
- Gather four (4) corners and center all together tightly.
- Wrap Mattress around Playard frame with the padded side facing inward.
- Secure the three (3) hook and loop straps by feeding them through the loops on the end of the Mattress and folding them back onto themselves.
- Place folded Playard into carry bag so that the handle comes through the opening between each side of the zipper.
Bassinet Assembly and Removal
To Assemble Bassinet:
ATTENTION: Playard must be fully assembled and securely locked before installing or using the bassinet feature. You will need to remove the mattress from the bottom of the Playard to use inside your Bassinet.
- Position the Bassinet over and down into the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place.
- Assemble Mattress Support Tubes (if equipped) by inserting the two (2) male tubes into the two (2) female tubes.
- Insert the assembled Mattress Support Tubes into the loops provided on the bottom of the Bassinet.
- Place the Mattress into the Bassinet with the padded side facing upward. Note: Fasten tabs underneath the Mattress secure it in place.
To Remove Bassinet:
- Remove Mattress from Bassinet.
- Remove Canopy.
- Unsnap all clips and lift Bassinet.
Mobile Assembly (Fixed)
ATTENTION: DO NOT attach Mobile to Canopy until Canopy is correctly installed. A crib mobile is intended for visual stimulation and is not intended to be grasped by the child. If attached to the crib or playpen, remove when baby begins to push up on hands and knees. Always attach all provided fasteners tightly. DO NOT add additional strings and straps. DO NOT attach the Mobile with child in Playard or Bassinet. DO NOT remove the Mobile before retracting or removing the Canopy.
Contents:
- (a) 1 Mobile Lower Arm
- (b) 1 Mobile Arm Holder
- (c) 1 Mobile Upper Curved Arm
- (d) 1 Mobile Tri-shaped Arm
- (e) 3 Toys (toys may vary)
- Insert the Mobile Lower Arm (a) into the Mobile Arm Holder (b) until locked together.
- Insert the Mobile Upper Curved Arm (c) into the Mobile Lower Arm (a, b) until locked together.
- Snap the Mobile Tri-shaped Arm (d) onto the end of the Upper Curved Arm (a, b, c). Connect each of the three Toys (e) to the Mobile by threading the string into the slot at the end of each arm.
- Insert the bottom of the Mobile Arm into the frame of the Playard.
Changing Table Assembly and Removal
To Assemble Changing Table:
ATTENTION: Playard must be fully assembled and securely locked before installing or using the changing table feature.
- Connect the two (2) Long Curved Bars together.
- Insert the assembled curved bars into the Changing Table fabric. Slide the Curved Bars around inside the sleeve of the Changing Table.
- Connect the two (2) Short Bars to each end of the Long Curved Bar. Make sure that the knobs are both facing down and in the same direction on each end.
- Insert Connector Knob Prongs into holes located on both corners of the Playard.
- Turn the Connector Knobs counter clockwise to lock into place.
- Flip Changing Table over onto Playard.
- Snap the two (2) buttons on the flap down onto the Playard.
IMPORTANT: Check that the Changing Table is correctly and securely installed BEFORE each use.
To use changing table restraint system:
- Place child on changing table, ensuring hands and arms are clear of the restraint. Bring the restraint around the child's waist and clip the male and female ends of the buckle together.
- Tighten strap until it fits snug around child's waist. DO NOT OVER TIGHTEN.
- To remove, unsnap the buckle.
ATTENTION: NEVER use changing table if it is damaged or broken.
To remove changing table:
- Flip Changing Table to the outside of the Playard.
- Unsnap fabric flap of Changing Table from Playard.
- Twist Connector Knobs clockwise to unlock.
- Remove Changing Table from Playard and disconnect the Short Bars from the Curved Bar by pressing on the snap buttons and pulling apart. Remove Curved Bar from Changing Table sleeve.
Parent Organizer / Diaper Stacker Assembly
- Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it snaps into place.
- Diaper Stacker: Skip to step 2.
- Connect the Parent Organizer/Diaper Stacker to the Playard by sliding the two (2) connecting clips over an open portion of the top rail of the Playard. Note: The Parent Organizer/Diaper Stacker can only be installed on open sides of the Playard where the connecting clips can easily be attached without interfering with other features.
Music Center
The Music Center is designed to be attached to the playard corners. It can be attached on the Changing Table's side or the Canopy's side.
WARNING: Keep batteries out of children's reach. Old and new batteries should not be mixed. Alkaline, standard carbon-zinc, and rechargeable nickel-cadmium batteries should not be mixed. Remove batteries before storing music center for a long period of time.
Music Center Operation:
The Music Center requires 4 AA batteries. Unscrew the battery door screws and pull outward on the battery door. Install batteries as shown. Re-install battery door and secure with screws.
- To activate the unit, press the [on/off button]. Press the button a second time to switch the unit off.
- To listen to SLEEP music, press the [sleep button]. Use the previous / next button to change the song. The Vol. ? or Vol. ? buttons control the unit's volume.
- To listen to PLAY music, press the [play button]. Use the previous / next button to change the song. The Vol. ? or Vol. ? buttons control the unit's volume.
- To listen to NATURE sounds, press the [nature button]. Use the previous / next button to change the sound. The Vol. ? or Vol. ? buttons control the unit's volume.
- VIBRATION: To use the vibration, press the [vibration button] down once to activate the first speed, press again for a Medium speed, and once more for the faster speed. Press [vibration-down-arrow] to reduce the speed.
- NIGHT LIGHT: To use the night light, press the [night-light-button] button. The light has 3 settings of brightness and is controlled by the same button.
- VOICE RECORDER: To use the Voice Record function, press the [record-button] button and speak into the microphone to record your 10-second voice message. Press the [play-button] to hear the message.
- VOICE ACTIVATION: To use the Voice Activation function, press the [voice-activation-button] twice if the unit is powered off. If the unit is already powered on, press the [voice-activation-button] once. The voice activation light will be illuminated when in voice activation mode. If your infant cries, their voice will activate the sleep music. When voice activation is enabled, sleep mode is active for 2 hours.
- MP3 FUNCTION: Use the input jack to attach your MP3 player. Press the [mp3-button] button to select the MP3 input. Your MP3 music will play through the unit and override the unit's music. To listen to the unit's music, depress the [mp3-button] button. Volume will be controlled by the MP3 player.
Maintenance and Cleaning Instructions
- Use only household mild soap and warm water.
- DO NOT USE BLEACH.
- DO NOT MACHINE WASH.
Contact Us
If you experience any difficulty in using this product or have a question regarding these instructions, please contact our Customer Service Department:
Phone: ? 1-800-328-7363 (8:00 A.M. - 4:30 P.M. Pacific Standard Time)
Website: ? http://www.babytrend.com
Mail:
Baby Trend, Inc.
1607 S. Campus Ave.
Ontario, CA 91761
Please have your model number and manufacturing date available when you call. This information can be found on a small sticker under the playard.
Please do not return the product to the store, as once it is returned it cannot be re-sold and the materials and energy used to make it are wasted.
