Bouncepad Core Static 60 Assembly Instructions

Assembly Instructions

Tighten screw(s) using hand tools. Using electric tools may damage your Bouncepad.

Section A: Fixing from Below

Follow steps A if "Fixing from below".

Step A1: Mark Drill Locations

Using the Mount Washer, mark the drill hole locations on your mounting surface.

Diagram shows a Mount Washer, M4 Split Washer, M4 Locking Nut, and a 7mm Spanner. Text indicates marking drill hole locations.

Step A2: Drill Holes

Drill each hole using the specified drill bit sizes: Ø5.0mm Drillbit and Ø16.0mm Holesaw.

Diagram shows a Ø5.0mm Drillbit and a Ø16.0mm Holesaw. Text indicates drilling holes.

Step A3: Secure Socket Screws

Locate and screw the M4x40mm Socketset Screws into the desk or surface as shown.

Diagram shows an M4x40mm Socketset Screw being screwed into a desk surface.

Step A4: Secure the Arm

Secure the arm to the surface. Locking Nuts offer higher security.

Diagram shows the assembled arm secured to a surface, with text highlighting the use of locking nuts for security.

Step A5: Proceed

Go to step 1 for tablet attachment.

Section B: Fixing from Above

Follow steps B if "Fixing from Above".

Step B1: Mark Drill Locations

Using the Mount Plate, mark the drill hole locations as shown.

Diagram shows a Mount Plate with drill hole markings.

Step B2: Drill Holes

Drill each hole using the specified drill sizes: Ø2.5mm Drillbit and Ø16.0mm Holesaw.

Diagram shows a Ø2.5mm Drillbit and a Ø16.0mm Holesaw. Text indicates drilling holes.

Step B3: Attach Mount Plate Cover

Locate the Mount Plate Cover onto the Static60.

Diagram shows a Mount Plate Cover and an M4x10mm Countersunk Screw. Text indicates placing the cover onto the Static60.

Step B4: Join Static60 and Mount Plate

Join the Static60 and Mount Plate in the orientation shown.

Diagram illustrates joining the Static60 and Mount Plate.

Step B5: Secure Static60 to Surface

Secure the Static60 to the surface using the 4x countersunk fixings (No.8 Countersunk Self-tapping Screws).

Diagram shows the Static60 being secured to a surface with screws.

Step B6: Adhere Mount Cover

Adhere the Mount Cover onto the Mount Plate using the adhesive tabs.

Diagram shows the Mount Cover being attached to the Mount Plate with adhesive.

Step B7: Proceed

Go to step 1 for tablet attachment.

Section C: Tablet Attachment (Steps 1-7)

Step 1: Attach Shell

Locate and attach the Shell to the Static60 in the correct orientation.

Diagram shows the Shell being attached to the Static60.

Step 2: Attach Mounting Plate to Tablet

Important: Before attaching the Mounting Plate, fully clean the back of the tablet with the provided wipe and allow it to fully dry. For optimal adhesion, press firmly and leave for 72 hours in a 20°C environment before use. Do not reposition. Do not use prior to the 72 hours.

Remove the Mounting Plate adhesive backing. Attach level and centrally to the Tablet back as shown, choosing either Landscape or Portrait orientation.

Diagram shows the Mounting Plate adhesive backing being removed and the plate being attached to the back of a tablet in Landscape and Portrait orientations.

Step 3: Attach Flat Cable to Tablet

Attach the Flat Cable to the Tablet with the U-Bend Head.

Diagram shows the Flat Cable with its U-Bend Head being connected to the tablet.

Step 4: Secure Flat Cable

Secure the Flat Cable to the Mounting Plate with the Cable Clamp as shown.

Diagram shows the Cable Clamp securing the Flat Cable to the Mounting Plate.

Step 5: Feed Cable and Locate Tablet

Remove the Fixing Covers. Feed the Flat Cable into the assembly and locate the Tablet in the chosen orientation.

Diagram shows Fixing Covers being removed, the Flat Cable being fed through the assembly, and the tablet being positioned.

Step 6: Secure Tablet and Covers

Secure the Tablet to the Shell and attach the Fixing Covers as shown.

Diagram shows the tablet secured to the shell and the Fixing Covers being attached.

Step 7: Connect Power

Connect the tablet to power. Installation is now complete.

Diagram shows a power plug and socket, indicating the final connection step.

	Bouncepad Core Elevate Assembly Instructions \| Secure Tablet Mounting Step-by-step guide to assembling the Bouncepad Core Elevate, a versatile and secure tablet and iPad mounting solution. Includes parts list, tools required, and installation tips.
	Bouncepad Core Static 60 Desk Mounted Tablet Holder Assembly Guide Detailed assembly guide for the Bouncepad Core Static 60 desk-mounted tablet holder. Learn how to install your tablet holder with clear, step-by-step instructions, including tools required, parts list, and mounting options for fixing from below or above.
	Bouncepad Core Elevate Slim Assembly Instructions Step-by-step assembly instructions for the Bouncepad Core Elevate Slim tablet and iPad mount.
	Bouncepad Original Elevate Assembly Instructions Comprehensive, step-by-step assembly guide for the Bouncepad Original Elevate tablet stand, detailing parts, tools, and installation procedures for a secure and functional setup.
	Bouncepad Original Floorstanding Assembly Instructions Assembly instructions for the Bouncepad Original Floorstanding unit, including steps for attaching a branding mount or front board.
	Bouncepad Original Elevate + Brother Printer Mount Assembly Guide Comprehensive assembly instructions for the Bouncepad Original Elevate + Brother Printer Mount, guiding users through the setup process for printers and tablets.
	Bouncepad Elevate Slim Assembly Instructions Step-by-step guide for assembling the Bouncepad Elevate Slim tablet enclosure, including tools required, components, and installation procedures.