Bouncepad Core Static 60 Assembly Instructions

Tools Required

• Pencil
• Electric Drill
• 7mm Spanner or Adjustable Spanner
• 5.0mm Drillbit
• 2.5mm Drillbit
• 16mm Holesaw
• Socket Driver

Important Notes

Note on Tightening:Tighten screw(s) using hand tools only. Using electric tools may damage your Bouncepad.

Mounting Surface Thickness:

• Maximum: 25mm (1 inch)
• Minimum: 34mm (1 5/16 inch)

In the Box

The following components are included:

• Flat Cable
• Fixings Kit
• Tablet Mount Plate
• Shell
• Static60 Mounting Arm
• Surface Mounting Kit

Fixings List

Note:Due to the modular nature of the product range, you may receive additional fixings in the kit.

• 4x No.8 Countersunk Self-tapping Screws
• 4x M4x10mm Countersunk Screws
• 4x M4 Wing Nuts
• 2x 3mm x 6mm Pan Head Screws
• 4x M4x40mm Socketset Screws
• 4x M4x16mm Buttonhead Screws
• 1x T20 Pin Torx Driver Bit
• 1x Cable Clamp
• 4x M3x10mm Countersunk Screws
• 1x Mount Washer
• 1x Case Washer
• 1x T10 Pin Torx Allen Key
• 8x M4 Split Washers
• 4x M4 Locking Nuts
• 1x Cleaning Wipe

Assembly - Fixing from Below

Step A1: Mark Drill Locations

Using the provided Mount Washer, place it on the mounting surface and mark the drill hole locations.

Diagram Description: Shows a Mount Washer placed on a surface, with a pencil marking through its holes.

Step A2: Drill Holes

Drill each marked hole using the specified drill bit. For the mounting holes, use the 5.0mm drill bit.

Diagram Description: Shows a drill with a 5.0mm drill bit drilling into the marked holes on the surface.

Step A3: Insert Socketset Screws

Locate and screw the M4x40mm Socketset screws into the desk or mounting surface as shown.

Diagram Description: Shows the M4x40mm Socketset screws being screwed into the surface.

Step A4: Secure the Arm

Secure the Static60 Mounting Arm to the surface using the M4 Locking Nuts and M4 Split Washers. Locking Nuts offer higher security.

Diagram Description: Shows the arm being attached to the surface with M4 Locking Nuts and M4 Split Washers, with a 7mm spanner being used.

Step A5: Proceed to Tablet Attachment

Go to Step 1 of the Tablet Attachment section.

Assembly - Fixing from Above

Step B1: Mark Drill Locations

Using the Tablet Mount Plate, place it on the mounting surface and mark the drill hole locations as shown.

Diagram Description: Shows the Tablet Mount Plate positioned on the surface, with a pencil marking the hole locations.

Step B2: Drill Holes

Drill each marked hole using the specified drill sizes. Use the 2.5mm drill bit for pilot holes and the 16.0mm holesaw if routing the cable through the surface.

Diagram Description: Shows drilling with a 2.5mm drill bit and a 16.0mm holesaw.

Step B3: Attach Mount Plate Cover

Locate the Mount Plate Cover onto the Static60 arm.

Diagram Description: Shows the Mount Plate Cover being placed onto the Static60 arm.

Step B4: Join Arm and Plate

Join the Static60 arm and the Tablet Mount Plate in the orientation shown.

Diagram Description: Shows the Static60 arm and the Tablet Mount Plate being connected.

Step B5: Secure to Surface

Secure the Static60 arm to the surface using the 4x countersunk fixings (No.8 Countersunk Self-tapping Screws).

Diagram Description: Shows the arm being screwed to the surface with the self-tapping screws.

Step B6: Adhere Mount Cover

Adhere the Mount Cover onto the Mount Plate using the adhesive tabs.

Diagram Description: Shows the Mount Cover being attached to the Mount Plate.

Tablet Attachment

Step 1: Attach Shell

Locate and attach the Shell to the Static60 arm in the correct orientation.

Diagram Description: Shows the Shell being attached to the Static60 arm.

Step 2: Attach Mounting Plate to Tablet

Clean the back of the tablet thoroughly with the provided Cleaning Wipe and allow it to dry completely. Remove the adhesive backing from the Mounting Plate. Attach the Mounting Plate level and centrally to the tablet's back, choosing either Landscape or Portrait orientation as required.

Important Adhesion Note:For optimal adhesion, press firmly and leave the tablet undisturbed for 72 hours in a 20°C environment before use. Do not reposition or use the tablet before this 72-hour period.

Diagram Description: Shows cleaning the tablet back, removing adhesive, and attaching the Mounting Plate to the tablet back in both Landscape and Portrait orientations.

Step 3: Connect Flat Cable

Attach the Flat Cable to the tablet using its U-Bend Head.

Diagram Description: Shows the Flat Cable's U-Bend Head being connected to the tablet.

Step 4: Secure Flat Cable

Secure the Flat Cable to the Mounting Plate using the Cable Clamp as shown.

Diagram Description: Shows the Cable Clamp securing the Flat Cable to the Mounting Plate.

Step 5: Feed Cable and Locate Tablet

Remove the Fixing Covers from the arm assembly. Feed the Flat Cable into the assembly and then locate the tablet (with the attached Mounting Plate) into the chosen orientation on the arm.

Diagram Description: Shows fixing covers being removed, the Flat Cable being fed through the arm, and the tablet being placed into the arm's holder.

Step 6: Secure Tablet and Attach Covers

Secure the tablet to the Shell using the appropriate fixings (e.g., 2x 3mm x 6mm Pan Head Screws, 4x M3x10mm Countersunk Screws). Attach the Fixing Covers to conceal the fixings.

Diagram Description: Shows the tablet secured to the shell with screws and the fixing covers being attached.

Step 7: Final Connection

Connect the tablet to its power source. The installation is now complete.

Diagram Description: Shows the tablet connected to a power cable.