Bouncepad Original Elevate
Assembly Instructions
Tools Required
- Socket Driver
- 10mm Spanner or adjustable spanner
In the Box
- Faceplate
- Case
- Elevate Pole
- Pair of Keys
- Tablet Set-up Kit
- Rubber Collar
- Base
- Height Limiter Cap
- Cover
- 1x Case Washer
- 4x M4 Split Washer
- 4x M6 Split Washer
- 4x M4x16mm Buttonhead screw
- 1x T20 Pin Torx Driver Bit
- 4x M6x25mm Countersunk screw
- 4x M6 Locking Nut
- 1x PZ3 Pozi Driver Bit
- 1x T30 Pin Torx Allen Key
- 2x M4x16mm Cap Head screw
- 1x T30 Pin Torx Driver Bit
Note: Due to the modular nature of our product range, you may receive additional fixings in the fixings kit.
Important Note
Tighten screw(s) using hand tools; using electric tools may damage your Bouncepad.
Assembly Steps
Step 1: Secure Pole to Base
Orientate, locate, and secure the Elevate Pole to the Base. Ensure all fixings are installed correctly.
Diagram Description: Shows the Elevate Pole being attached to the Base, with arrows indicating correct alignment and screw points.
Step 2: Remove Clamp
Loosen and remove the clamp from the Elevate Pole.
Diagram Description: Illustrates loosening and detaching the clamp mechanism.
Step 3: Remove Protective Stickers
Peel the protective stickers off the Elevate Pole.
Diagram Description: Shows the removal of protective film from the pole.
Step 4: Attach Cover
Attach the Cover as shown.
Diagram Description: Depicts the placement and attachment of the cover component.
Step 5: Reattach Clamp
Reattach the clamp without tightening. Align slots on both the clamp and pole as shown.
Diagram Description: Shows the clamp being placed back onto the pole, highlighting slot alignment.
Step 6: Secure Case to Pole
Locate and secure the Case onto the Elevate Pole. Tighten by hand.
Diagram Description: Illustrates mounting the main case onto the pole and hand-tightening screws.
Step 7: Remove Faceplate
Unlock and remove the Faceplate from the Bouncepad Case.
Diagram Description: Shows the process of unlocking and detaching the faceplate.
Step 8: Route Power Cable
Feed the Power Cable through the Case, Elevate Pole, and Height Limiter Cap.
Diagram Description: Depicts the power cable being threaded through the various components of the stand.
Step 9: Attach Height Limiter Cap
Attach the Height Limiter Cap to the Elevate Pole. Feed the cable through the Base.
Diagram Description: Shows the height limiter cap being fitted onto the pole and the cable routed through the base.
Step 10: Install Tablet Setup Kit
Install the Tablet Setup Kit. Each kit is specific per device and case.
Diagram Description: Illustrates the installation of tablet-specific components like corner pieces and supports.
Step 11: Install Tablet and Connect Power
Install the Tablet into the Case and connect to the Power Cable.
Diagram Description: Shows the tablet being placed into the case and connected to the power source.
Step 12: Lock Faceplate
Locate and lock the Faceplate to the Case.
Diagram Description: Depicts the final locking of the faceplate onto the case.
Step 13: Adjust Height and Tighten Clamp
Adjust the Elevate Pole to your desired height and tighten the clamp.
Diagram Description: Shows the user adjusting the pole height and securing it with the clamp.
Step 14: Connect Power Source
14.1: Connect the Power Cable to its mains power source.
Diagram Description (14.1): Shows the power cable being plugged into a wall socket.
14.2: If installing a Battery Pack, connect the Power Cable and locate it into the Base.
Diagram Description (14.2): Illustrates connecting a battery pack and placing it within the base. Includes a note on approximate maximum battery pack dimensions: 91mm (length) x 56mm (width) x 25mm (Height).
Step 15: Fit Rubber Collar
With the Cover on the ground, locate and fit the Rubber Collar.
Diagram Description: Shows the rubber collar being fitted onto the base of the stand.
Step 16: Secure with Kensington Lock
Use a Kensington® Microsaver product to tether to a secure object. Refer to your Kensington® instructions for full details.
Diagram Description: Depicts a Kensington security cable being attached to the stand and a secure object.
Step 17: Installation Complete
Installation is now complete.
Additional Note: We recommend recording the key number so you can purchase additional keys in the future.
