FUFU&GAGA Cupboard Assembly Instructions

Important Information

Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference. ❓

AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, like a rug. ?️

IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time. ?‍?‍?

ANTI-TOPPLE WARNING! ⚠️ Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully. ?

IMPORTANT! ❗ It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months to assure stability throughout its lifespan.

For regular maintenance and cleaning of the frame, use a rag dipped in neutral detergent, wipe fully, and then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.

Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.

Tools and Parts

Please prepare the following tools: ?

• Screwdrivers (Phillips and Flathead)
• Hammer
• Other tools as indicated in assembly steps

⚠️ When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

Parts List:

Assembly Steps

Step 1

Insert quickfit screw (A) into corresponding holes in boards 1, 2, 4, 14 with a screwdriver. ??

Diagram shows: Boards labeled 1, 2, 4, and 14 laid flat. Multiple screws (A) are shown being inserted into pre-drilled holes on these boards.

Step 2

Insert quickfit screw (A) into corresponding holes in boards 3, 5, 7, 13 with a screwdriver. ??

Diagram shows: Boards labeled 3, 5, 7, and 13 laid flat. Multiple screws (A) are shown being inserted into pre-drilled holes on these boards.

Step 3

Attach board 11 to board 10 using long wooden dowel (C) first, then secure with screw (E). Ensure the dowel penetrates through board 10. ??

Attach another two board 11 to board 10, repeating the previous step.

Diagram shows: Board 10 standing vertically. Two boards labeled 11 are being attached to the sides of board 10 using dowels (C) inserted into holes and screws (E) securing them.

Step 4

Attach board 9 to board 11 using short wooden dowel (D) as shown. ?

Attach board 11 to board 10 as shown.

Diagram shows: Board 9 being attached to one of the boards labeled 11 using dowels (D). Another board labeled 11 is also shown being attached to board 10.

Step 5

Attach board 4 to boards 8, 9, 10 using short wooden dowel (D) and turn cam locks (B) clockwise to tighten. ?⚙️

Attach board 7 to boards 8, 9, 10 using long wooden dowel (C), insert cam lock (B) into board 8, and turn clockwise to tighten. Ensure the dowel penetrates through board 7. ?⚙️

Diagram shows: Board 4 being attached to a central structure (likely comprising parts 8, 9, 10) using dowels (D) and cam locks (B). Board 7 is then attached to the same structure using dowels (C) and cam locks (B).

Step 6

Insert quickfit screw (A) into corresponding holes in board 7 as shown. ??

Diagram shows: Screws (A) being inserted into pre-drilled holes on board 7.

Step 7

Attach boards 6 and 23 to board 7 and turn cam locks (B) clockwise to tighten as shown. ⚙️

Diagram shows: Boards labeled 6 and 23 being attached to board 7 using cam locks (B).

Step 8

Attach board 2 to boards 6 and 23 using wooden dowel (D) and turn cam locks (B) clockwise to tighten as shown. ?⚙️

Diagram shows: Board 2 being attached to the assembly formed by boards 6, 23, and the rest of the structure, using dowels (D) and cam locks (B).

Step 9

Cover board 1 (top panel) to the unit using wooden dowel (D) and turn cam locks (B) clockwise to tighten as shown. ?⚙️

Diagram shows: Board 1 being placed on top of the main cabinet structure and secured with dowels (D) and cam locks (B).

Step 10

Insert long wooden dowel (C) into boards 4, 7, 2. ?

Insert short wooden dowel (D) into board 11. ?

Diagram shows: Dowels (C) being inserted into specific holes on boards 4, 7, and 2. Dowels (D) are shown being inserted into board 11.

Step 11

Attach board 12 to the component with screw (E). Ensure the long wooden dowel must penetrate through board 12. ?

Diagram shows: Board 12 being attached to the main structure using screws (E). A close-up shows a dowel (C) from a previous step passing through board 12.

Step 12

Insert quickfit screw (A) into corresponding holes in board 12 as shown. ??

Diagram shows: Screws (A) being inserted into pre-drilled holes on board 12.

Step 13

Attach board 13 to board 14 using wooden dowel (D) first, then secure with screw (E) again. ??

Attach board 15 to board 14 using wooden dowel (D) and turn cam locks (B) clockwise to tighten as shown. ?⚙️

Diagram shows: Board 13 being attached to board 14 with dowels (D) and screws (E). Board 15 is then attached to board 14 using dowels (D) and cam locks (B).

Step 14

Attach board 8 to board 13 using long wooden dowel (C) and turn cam locks (B) clockwise to tighten. Ensure the dowel penetrates through board 13. ?⚙️

Attach board 5 to board 8 using short wooden dowel (D) and turn cam locks (B) clockwise to tighten. ?⚙️

Diagram shows: Board 8 being attached to board 13 using dowels (C) and cam locks (B). Board 5 is then attached to board 8 using dowels (D) and cam locks (B).

Step 15

Insert quickfit screw (A) into board 13 with a screwdriver as shown. ??

Diagram shows: Screws (A) being inserted into pre-drilled holes on board 13.

Step 16

Attach board 6 to board 13 and turn cam locks (B) clockwise to tighten as shown. ⚙️

Attach board 3 to boards 6, 14, 15 using wooden dowel (D) and turn cam locks (B) clockwise to tighten as shown. ?⚙️

Diagram shows: Board 6 being attached to board 13 using cam locks (B). Board 3 is then attached to boards 6, 14, and 15 using dowels (D) and cam locks (B).

Step 17

Connect two assembled components and turn cam locks (B) clockwise to tighten as shown. Recommend more than 2 people to assemble!! ?‍?‍?⚙️

Diagram shows: Two large sub-assemblies of the cupboard being joined together. Cam locks (B) are used to secure the connection. A note suggests needing more than two people.

Step 18

Fix back boards 18, 19, 20, 21, 22 to the main structure using nail/screw (K) as shown. ?

Diagram shows: The thin back panels (18-22) being attached to the rear of the assembled cabinet using screws (K).

Step 19

Fix hinge (H) to boards 16, 17 (doors) using screw (H) as shown. ??

Fix knob (F) to doors using screw (G) as shown. ??

Diagram shows: Hinges (H) being screwed onto the edges of door panels (16, 17). Knobs (F) are being attached to the front of the doors using screws (G).

Step 20

Attach board 16 (door) to the upper cabinet section by fixing the hinge with screw (J) as shown. ??

Attach board 17 (door) to the lower cabinet section by fixing the hinge with screw (J) as shown. ??

Diagram shows: The doors (16 and 17) with attached hinges being mounted onto the main cabinet structure using screws (J).

Step 21

If there is misalignment after installation, adjust the screws on the hinges to the best condition. ?

Diagrams show close-up views of cabinet hinges with arrows indicating adjustment points for vertical, horizontal, and depth alignment.

Step 22

Wall Mounting:

Fix part (N) to board 1 (top panel) using washer (P) and screw (L) at first. ?⚪

Fix part (M) (wall bracket) to a proper position on your wall. Then, fix part (N) to part (M) using washer (P) and screw (E) as shown. ??⚪

Diagram shows: Wall mounting brackets (M) being attached to the wall. The cupboard's top panel (1) has brackets (N) attached, which then connect to the wall brackets (M) using washers (P) and screws (E).

Warranty Information

WARRANTY CLAIMS

• There is a 30-day warranty for broken furniture or other problems that do not work properly. The warranty starts from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call to inquire. Provide your purchase order number and details of the problem for replacement parts. A response will be arranged within 48 hours. If parts are out of stock, a shipping date will be provided.
• The product must be used in accordance with the instructions provided.
• For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Damage during installation is not covered, but damage during transportation is included.

Scope of Responsibility

• FUFU&GAGA shall not bear any responsibility for misuse, user damage, or loss of parts during the installation of furniture.
• Damage and scratches after use are not covered by the warranty.

Warranty Coverage Areas (in the US)

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns Policy

CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?

If you have purchased and simply changed your mind, follow the retailer's instructions for returns.

DEFECTIVE ITEMS

If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call first.

DAMAGED ITEMS

If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.

In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive a credit for the return.