Important Information
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
To avoid scratching: This furniture should be assembled on a soft layer, such as a rug.
To improve efficiency: Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
Anti-Topple Warning
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
Important Notes
It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.
Maintenance and Cleaning: For the frame, use a rag dipped in neutral detergent, wipe it, and then dry with a clean rag. For glass materials, wipe with a rag dampened with glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.
Tools Required
Please prepare the following tools:
- Screwdriver
- Hammer
Hardware and Parts Identification
When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.
Hardware:
- A (x 27): Ø6 x 35 mm
- B (x 27): Ø15 x 9.5 mm
- C (x 14): Ø4 x 40 mm
- D (x 20): Ø6 x 30 mm
- E (x 6): (Type E part)
- F (x 78): Ø4 x 12 mm
- G (x 8): Hinge
- H (x 10): Ø6 x 50 mm
Parts Overview:
The following parts are used in the assembly:
(Diagram shows an exploded view of the cabinet with parts numbered 1 through 19. These are structural panels and components.)
WARNING:
- Always install tipover restraint provided.
- Never put a TV on this product.
- Never allow children to stand, climb, or hang on drawers, doors, or shelves.
- Never open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
This is a permanent label. Do not remove! ⚠️
Assembly Steps
Step 1
Hardware: A (x 20) - Ø6 x 35 mm
Action: Screw eccentric rod (A) into boards 4, 6, 7, 8, 9, and 11 with a screwdriver. The diagram shows rods (A) being inserted into pre-drilled holes on the boards and rotated 180° for tightening.
Step 2
Hardware: B (x 4) - Ø15 x 9.5 mm, D (x 4) - Ø6 x 30 mm
Action: Connect board 13 to board 7; board 14 to board 11 using wooden dowel (D). Add cam lock (B) into boards 13 and 14, and turn clockwise to tighten. The diagram illustrates the insertion of dowels and cam locks, with a 180° rotation indicator for the cam locks.
Step 3
Hardware: B (x 4) - Ø15 x 9.5 mm, D (x 4) - Ø6 x 30 mm
Action: Connect board 5 to board 4; board 10 to board 8 using wooden dowel (D). Add cam lock (B) into boards 5 and 10, and turn clockwise to tighten. The diagram shows the assembly process for these connections.
Step 4
Hardware: C (x 4) - Ø4 x 40 mm, D (x 4) - Ø6 x 30 mm
Action: Attach board 7 to board 5; board 11 to board 10 using wooden dowel (D), and fix with screw (C). The diagram shows the boards being joined with dowels and secured with screws.
Step 5
Action: Insert back board 19 along grooves as shown. The diagram illustrates sliding the back panel into the designated grooves on the cabinet structure.
Step 6
Hardware: B (x 2) - Ø15 x 9.5 mm, C (x 8) - Ø4 x 40 mm, H (x 10) - Ø6 x 50 mm
Action 1: Attach board 6 to board 4 and 7 using long wooden dowel (H), and fix with screw (C). Add cam lock (B) into board 13 and turn clockwise to tighten.
Action 2: Attach board 9 to board 8 and 11 using long wooden dowel (H), and fix with screw (C). Add cam lock (B) into board 14 and turn clockwise to tighten. The diagrams show the assembly of the main cabinet frame sections.
Step 7
Hardware: A (x 7) - Ø6 x 35 mm
Action: Screw eccentric rod (A) into board 1 and 2 with a screwdriver. The diagram shows rods (A) being screwed into the boards.
Step 8
Hardware: B (x 2) - Ø15 x 9.5 mm, D (x 2) - Ø6 x 30 mm
Action: Attach board 3 to board 1 using wooden dowel (D), add cam lock (B) into board 3 and turn clockwise to tighten. The diagram shows the connection of boards 1 and 3.
Step 9
Hardware: B (x 5) - Ø15 x 9.5 mm, D (x 4) - Ø6 x 30 mm
Action: Attach board 12 to board 2 using wooden dowel (D), add cam lock (B) into board 12 and turn clockwise to tighten. The diagram illustrates this assembly step.
Step 10
Hardware: C (x 2) - Ø4 x 40 mm, D (x 2) - Ø6 x 30 mm
Action: Attach board 2 to board 3 using wooden dowel (D), and fix with screw (C). The diagram shows the connection of boards 2 and 3.
Step 11
Action: Insert back board 18 along grooves as shown. The diagram shows the back panel being slid into place.
Step 12
Hardware: B (x 5) - Ø15 x 9.5 mm
Action: Attach board 9 to boards 1, 2, and 12, add cam lock (B) into and turn clockwise to tighten. The diagram shows the assembly of the upper section of the cabinet.
Step 13
Hardware: B (x 5) - Ø15 x 9.5 mm
Action: Attach board 6 to boards 1, 2, and 12, add cam lock (B) into and turn clockwise to tighten. The diagram shows the assembly of the lower section of the cabinet.
Step 14
Hardware: F (x 16) - Ø4 x 12 mm, G (x 8) - Hinge
Action: Fix hinge (G) to board 15, 16, and 17 with screw (F) as shown. The diagrams illustrate attaching hinges to the door/drawer panels.
Step 15
Hardware: F (x 32) - Ø4 x 12 mm
Action: Assemble board 16 to board 7; board 15 to board 2; board 17 to board 11 by fixing hinge with screw (F) as shown. The diagrams show the doors/drawers being attached to the cabinet.
Step 16
Hardware: E (x 6), F (x 30) - Ø4 x 12 mm
Action: Fix part (E) to the cabinet with screw (F) as shown. The diagram shows the final attachment of smaller components.
Warranty
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
- Before making a claim, please call with your purchase order number and details of the problem. A response will be arranged within 48 hours. If the item is out of stock, a shipping date will be provided.
- The product must be used in accordance with the instructions provided.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and returned within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Damage during installation is not covered, but damage during transportation is included.
Scope of Responsibility
- The manufacturer shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
- After use, damage and scratches of the furniture are not covered by the warranty.
The Warranty Relates to All Bought in The US and Covers The Following Areas:
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns
CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
- If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.
DEFECTIVE ITEMS
- If your item is defective in any way, i.e. it doesn't work but you can't identify why, please call us in the first instance.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
- In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.
AFTER-SALES CONTACT
- Email: feedbackstation@163.com
- Phone: (303)800-6387
